• Energy Research
• Closed Access close
• Restricted close
• 7. Clean energy close
• Chinese Academy of Sciences close

New zinc phthalocyanine (ZnPc-TDA), peripherally functionalized with donor-acceptor conjugates was synthesized, and its optical, thermal, electrochemical, and photovoltaic properties were studied. The black ZnPc-TDA exhibited both excellent solubility in common organic solvents, and broad absorption covering the range 300-900 nm. The photovoltaic devices with the configuration of ITO/PEDOT-PSS/ZnPc-TDA:PCBM/LiF/Al produced short circuit current densities of 2.26 mA/cm(2), the open circuit voltage of 0.68 V and power conversion efficiency of 0.4% under AM1.5G illumination. (C) 2010 Elsevier B.V. All rights reserved.

Bioenergy is considered a sustainable substitute to fossil-fuel resources and the development of a prudent combination of renewable and innovative conversion technologies are essential for the valorization and effective conversion of biowaste to value-added commodities. Here, a negative pressure-induced carbonization process was proposed for the valorization of lignin-enriched biowaste precursor to bio-oil and environmental materials (biochar) at various temperatures. The high heating values (HHV) of the as-prepared biochars from the lignin enriched precursor under negative pressure (low-medium vacuum) were within 25.9-31.5 MJ/kg, which matched satisfactorily to the commercial charcoal. Whereas, the bio-oils produced from the lignin enriched precursor under vacuum conditions was a blend of complex aromatic and straight-chain hydro-carbons, including aldehyde, ketone, phenol, and furans, exhibiting ability as potential heating-oil with HHV within 21.2-28.2 MJ/kg. Moreover, the biochars produced under vacuum environments at higher temperature showed greater stability (22.5-35.9%) than those produced under N2 atmosphere.

Abstract This paper presents a novel and environmentally friendly production of direct reduced iron (DRI) technology using biomass as an additive agent in iron ore pellets and simulated biomass-derived syngas as the reducing agent. The effects of biomass addition on iron ore pellets reduction and consequent reduction kinetics in simulated biomass-derived syngas atmosphere were investigated. The results demonstrated that the biomass addition improved the pellet porosity and specific surface area, thus increasing both the reducibility and reduction rate and decreasing the apparent activation energy for pellet reduction. Mathematical modelling of experimental data indicated an interfacial chemical reaction mechanism with FeO → Fe as the rate controlling step. The simulated biomass syngas is an alternative gas-based reductant to natural gas, coal gas, more than 99.5% reduction degree of the oxidized pellets was reduced at 1323 K within 20 min. The apparent activation energies were 86.05 kJ·mol −1 , 97.53 kJ·mol −1 for the pellets with and without biomass addition. The proposed iron ore reduction process therefore would be a potential to reduce iron directly using biomass with high efficiency and real environmental benefits.

Abstract A high-flux solar simulator is essential for evaluating solar thermal components under controlled and adjustable flux input conditions. This study presents a newly built high-flux solar simulator composed of 19 individual units. Each unit includes a xenon short-arc lamp (each consuming up to 6 kW electricity power) coupled with a truncated ellipsoidal reflector, a cooling blower, and a power module. The power module yields a current in the range of 50–160 A. The number of lamps in use is flexible, which allows for a wide range of radiation flux (10%–100%) on the focal plane. The radiation power, peak value, flux distribution on the circular target plane, and conversion efficiency are evaluated based on a flux mapping method. The results indicate that the proposed solar simulator is capable of achieving thermal power of 23.3 kW, peak flux in excess of 1.78 MW/m2, a stagnation temperature exceeding 2360 °C, and average irradiance of 773.4 kW/m2 on the focal plane (diameter of 260 mm). The electro-thermal conversion efficiency of the simulator is 35.7%. A ray-tracing method was employed, and the simulation results were found to be in good agreement with those in the experiments. An experimental test of a volumetric ceramic receiver was conducted, and the results indicate the availability and applicability of the high-flux solar simulator when carrying out studies about solar receivers.

Abstract The absorption refrigeration system driven by low grade heat sources, especially the waste heat sources, becomes more and more attractive in recent decades. However, most traditional absorption systems cannot achieve a high utilization rate of the waste heat with limited heat capacity. These systems are usually designed to obtain heat in the generator, which means that the waste heat sources cannot be utilized to the temperature lower than the generator temperature. This paper proposed a new structure heated by heat conduction oil in the generator and electric heating rings around the stripping section. This structure can simulate the temperature-distributed heat sources when the electric heating rings work. It can also simulate a traditional generator when the electric heating rings do not work. Influences of different heat distributions are analyzed in detail in this paper. The results show that the heat sources utilization rate will increase with the increase of the heat in the stripping section, while the coefficient of performance will be negatively affected by the increasing heat in the stripping section. By optimizing the heating structure, the coefficient of performance can be similar to that of a traditional system when the heat is just added in the middle and lower part of stripping section. The optimum utilization rate of heat sources in this test model can reach 1.8 times to that of a traditional system. Under this heating model, the lowest temperature required in the heating section is 82 °C when the heat conduction oil inlet temperature is 169 °C. It is much lower than the temperature inside the generator, which is 137.3 °C.

Abstract Cu2BaSn(S,Se)4 (CBTSSe) solar cells are emerging photovoltaic devices due to their high theoretical efficiencies of ~31%, environment-friendly and earth-abundant composition, low density of non-recombination defects, and so on. However, the record efficiency of CBTSSe solar cell is only 5.2%, showing the importance of studying their performance via numerical analysis to further enhance their practical efficiencies. In this paper, the effect of absorber and buffer layers on performances of Cu2BaSnS4 (CBTS) solar cells are firstly systematically studied via the SCAPS-1D software to provide a platform for the study of the effect of MoS2 interlayer on the performances of CBTS solar cells. The highest PCE of CBTS solar cell with a 30 nm CdS buffer layer is 11.87%. The PCE of CBTS solar cell with a 0.8 μm CBTS absorb layer is 12.51%, indicating that the CBTS solar cell is a potential low-cost solar cell due to its large optical absorption coefficient (α > 104 cm−1). The efficiency of CBTS solar cell is improved to 16.47% when the carrier concentration of CBTS is 1016 cm−3. The relationship between the performance of solar cell and the band gap, thickness, donor concentration, acceptor concentration of MoS2 interlayer is systematically investigated on the basis of the optimized efficiency. It is found that MoS2 interlayer plays an important role in the performance of CBTS solar cell. The p-type MoS2 has a beneficial effect on the efficiency improvement while the n-type MoS2 has a negative effect on the efficiency enhancement. The highest PCE of CBTS solar cell is as high as 18.28% when the thickness and the acceptor concentration of MoS2 are 4 nm and 1019 cm−3, respectively. Our simulation result provides a promising research direction to further improve the actual efficiency of the CBTS solar cell.

Ferrocene was introduced as a solid additive in organic solar cells (OSCs). The use of ferrocene provides PM6:Y6 based device with improved performance and stability, demonstrating its great potential in the fabrication of efficient and stable OSCs.

A new small molecule acceptor, Y18, was designed and synthesized. Over 17% efficiency was obtained with single junction solar cells based on Y18.

An object-oriented white box design procedure of thermoelectric power generators is proposed based on a system level analysis.