• Energy Research
• Restricted close
• Open Source close
• National Research Council close

AbstractBACKGROUND: Inappropriate utilisation of biosolids may adversely impact agrosystem productivity. Here, we address the response of wheat (Triticum durum) to different doses (0, 40, 100, 200 and 300 t ha−1) of either municipal solid waste (MSW) compost or sewage sludge in a greenhouse pot experiment. Plant growth, heavy metal uptake, and antioxidant activity were considered.RESULTS: Biomass production of treated plants was significantly enhanced at 40 t ha−1 and 100 t ha−1 of MSW compost (+48% and +78% relative to the control, respectively). At the same doses of sewage sludge, the increase was only 18%. Higher doses of both biosolids restricted significantly the plant growth, in concomitance with the significant accumulation of heavy metals (Ni2+, Pb2+, Cu2+ and Zn2+), especially in leaves. Leaf activities of antioxidant enzymes (ascorbate peroxidase, glutathione reductase, catalase and superoxide dismutase) were unchanged at 40 t ha−1 MSW compost or sewage sludge, but were significantly stimulated at higher doses (200–300 t ha−1), together with higher leaf concentration of reduced glutathione.CONCLUSION: This preliminary study suggests that a MSW supply at moderate doses (100 t ha−1) could be highly beneficial for wheat productivity. Copyright © 2010 Society of Chemical Industry

Diesel engine exhausts from a common rail 3.0 L F1C diesel engine were analyzed at two different load conditions of the WLTC testing cycle downstream of both the diesel particulate filter (DPF) and selective catalytic reactor (SCR) to verify their effect on the characteristics of carbon particulate matter. An array of chemical, physical and spectroscopic techniques (gas chromatography coupled with mass spectrometry (GC-MS), mobility analyzer, UV-Visible absorption and fluorescence spectroscopy) was applied for characterizing polycyclic aromatic hydrocarbons (PAH), heavy aromatic compounds and soot, constituting the particulate matter (PM) sampled from the exhaust. The engine was operated in half load (HL) (188 Nm, representing the more common condition for engine in urban traffic) and full load (FL) (452 Nm, representing the best performance of the engine operation) conditions, at the same engine speed (2000 rpm). Soot formation was enhanced in HL condition, with respect to FL, but, just because of the much lower soot amount, the after-treatment systems in this last condition resulted to be less efficient in the soot abatement. Indeed, the abatement through DPF was about 40% lower in the FL condition with respect to HL condition, and any significant further concentration decrease was found after SCR, in both conditions. By contrast, PAH concentration after DPF abatement was found to be higher in the HL with respect to FL condition. A further PAH concentration decrease of about 30% was found after the SCR in the HL condition whereas in FL the reduction was only about 5-6%. Also the heavy aromatic compounds having molecular weight above the GC-MS detection limit (300 u), were mitigated by SCR. Therefore, SCR did not cause a further soot reduction, whereas it was effective in largely reducing PAH and heavy aromatics emissions, especially in the lower temperature condition featuring the half-load condition, when combustion efficiency is worse. Moreover, SCR system reduced the emission of small particles probably due to an enhanced agglomeration of particles, with beneficial effect on the harmfulness to human health.

Originally developed and validated at the Cabauw (Netherlands) topographically flat onshore location, the alpha-I wind resource extrapolating method was tested at the FINO3 offshore site in the North Sea (Germany). The aim was to prove its validity also when applied over a substantially different environment in terms of surface characteristics and stability conditions. Data from local mast at 30, 80, and 100 m were used, with extrapolations to 80-m and 100-m turbine hub heights accomplished based on 30-m turbulence intensity observations. Trained over a 2-year period (2011-2012), the method was validated on year 2013. Similarly to the onshore application, the method was reliable in extrapolating wind speed to both 80 m and 100 m, with bias within 5%, NRMSE = 0.20 and r = 0.94. Conversely, scores were largely better than at the onshore site in predicting the annual energy yield, biased by 0.41-1.02% at 80 m, and 1.12-1.36% at 100 m. The method proved to be highly sensitive to the stability classification, as not considering this option increased its biases to 4.51-5.93% at 80 m, and 7.46-8.23% at 100 m. Method's reliability might suitably help reduce the number of masts installed throughout a large offshore area.

[object Object]

In the anodisation of Nb in acidic fluoride solutions or warm aqueous alkali, and in that of Mo in concentrated phosphoric acid, impedance spectroscopy provides evidence that 3D film growth proceeds already during the active–passive transition. Indeed, linear potential dependences of both the inverse of the high-frequency capacitance and of the product of the high-frequency resistance times the steady-state current are observed already below the peak potential. Simultaneously, a pseudo-inductive loop at intermediate frequencies is detected in the impedance spectra. In the present paper, we propose a kinetic model for the interpretation of these data. The model assumes that the metal is covered with a non-stoichiometric oxide containing at least two oxidation states of the cation. The processes of oxidative dissolution of the lower valence cations and their transformation to cations of higher valence, leading to passivation, explain the shape of the I–E curve. These processes are limited by both charge transfer at the film–solution (F/S) interface and transport of cation vacancies through the film. Thickening of the oxide film is assumed to proceed simultaneously, and is limited by transport of oxygen vacancies accelerated by an interfacial charge of cation vacancies.

Sul mercato esistono molti materiali adsorbenti (prevalentemente a base di carboni attivi eventualmente impregnati, zeoliti, alcuni ossidi metallici) per la desolforazione e la rimozione di VOC anche a temperatura e pressione ambiente. Tuttavia questi materiali mostrano capacità relativamente basse e/o cinetiche di cattura lente a temperatura ambiente, che inevitabilmente si traducono nella necessità di utilizzare grandi volumi di impianto. La ricerca svolta dall'IRC-CNR Napoli e DSC-UNINA, in stretta collaborazione, parte dalla considerazione che lo sviluppo di nuovi materiali e processi ad alta efficienza per la desolforazione (in particolare attraverso adsorbimento) rappresenta un traguardo cruciale per l'impiego vantaggioso di una fonte energetica rinnovabile e residuale quale il biogas, anche su piccola scala in un'ottica di generazione distribuita di energia. La ricerca è stata indirizzata allo sviluppo di materiali adsorbenti ad alte prestazioni e basso costo in grado di far fronte a condizioni operative assai diversificate in termini di temperature (già a partire da temperatura ambiente) e composizioni dei gas da trattare (es. presenza di altri inquinanti).

The modern Common Rail Diesel engine are, normally, optimised for being fuelled with the commercial Diesel fuel. The ECU calibrations are, consequently, defined to obtain the correct compromise between performances and emissions. It is, so, clear that if the engine is fuelled with an alternative bio-fuel with different characteristics (net heating value, stoichiometric A/F ratio, density, viscosity, etc.) the calibration must be modify. Interest in fuels from renewable sources and their use in transport has grown over the last decade. This is because of their biodegradability, potential improvements in exhaust emissions and benefits on the virtuous CO2 cycle of the earth. This paper demonstrates that it is possible to optimise the emissions and the performances of a light duty diesel C.R. engine fuelled with a vegetable derived fuel (Rapeseed Methyl-Ester) pure or blended with commercial Diesel fuel. Particularly in this paper the experimental results and the ECU control solutions referring to different fuel compositions are shown.

This paper is focused on the measurement issues and procedures for the characterization of medium voltage grids for narrowband power line communications (NB-PLCs), in the perspective of the use and integration of such technology into smart grids communication networks. The fundamentals are given for the characterization of the PLC channel, by means of noise and attenuation measurements. Suitable procedures are also developed for the characterization and modeling of the power system components in the frequency range of interest. Furthermore, the complete model of the PLC system is experimentally validated in a real case study.