• Energy Research
• 2016-2025close
• Closed Access close
• Open Source close
• Embargo close
• Renewable Energy close

Abstract In this work, energy analysis is carried out to account for inputs and outputs of energy and GHG emissions associated with the biodiesel production system. Jojoba oil is obtained by cultivation of the jojoba plant, harvesting of seeds followed by extraction of oil, which is then converted to biodiesel by the process of transesterification. Energy efficiency is expressed in terms of the net energy balance (NEB) and the net energy ratio (NER). The use of the byproducts (husk, cake or meal, waste residues and glycerin) are also included as a part of the system boundary. The results show that the NEB and NER values are calculated at 46724.1 MJ/ha (28.9 MJ/L biodiesel produced) and 2.16, respectively. At the same time, the total amount of GHG emissions are estimated at 2.28 kg-CO2eq/L biodiesel produced (66.0 g CO2eq/MJ biodiesel produced). Nevertheless, if manure is used as fertilizer for jojoba plant cultivation, the primary energy input will fall by 9.52% (to 22.49 MJ/L of biodiesel).

Abstract This paper investigates the performance of a variable ratio gearbox (VRG) used in a small fixed-speed wind turbine with active blades. The major components of the VRG-enabled drivetrain are an automatic-manual gearbox and squirrel cage induction generator that connects directly to the grid. The simplicity of this system may be appealing for applications when cost and reliability are of concern. It is an alternative to variable speed systems, which necessitate a modified generator and power conditioning equipment. During partial load operation the VRG provides a discrete set of rotor speeds. This allows the controller to track the wind speed and to achieve a greater efficiency. This study suggests three VRG ratios are sufficient to improve performance when used with active blades. A case study is presented where the performance is simulated using three different wind data sets. The study suggests that the VRG can improve production between 7 and 8.5% in low wind areas. The design procedure also illustrates a technique for finding the lowest and highest gear ratios needed for VRG design. These ratios allow the system to achieve the lowest cut-in and rated speeds. The approach also has useful implications for the design of a continuously variable transmission.

Abstract The price effect of the rising share of renewable electricity, which is called ‘merit-order-effect’, leads to noticeable changes in the German power industry and debates about the electricity market design. This paper estimates the merit-order-effect induced by variable renewable energy in the German-Austrian electricity sector with a multivariate regression model. The research focus lies on the impact of the estimated effects on the marketability of variable renewable electricity generation. The results show a systematic decline of the average market revenues for wind and photovoltaic plants in the period from January 2011 to December 2013. Current market data shows a continuation of this trend into 2016. According to the German long term goals for the use of renewables, wind and solar power will play a crucial role in the future electricity generation mix. If investments in these technologies will be profitable without any regulatory remuneration mechanisms in addition to the market revenues, depends on the further cost degression and the development of the merit-order-effect.

Abstract Gold nanoparticles (Au-NPs) seeded plasmonic nanofluids (PNFs) have shown promising results in overall performance enhancement of direct absorption solar collector (DASC) due to localized surface plasmon resonance (LSPR) effect. For the work presented here, Au-NPs were synthesized by the wet chemical method and were utilized to prepare plasmonic nanofluid. The surface plasmon resonance peak of Au-NPs was observed at 531 nm using UV–Visible spectrophotometer study. The testing for performance enhancement of gold plasmonic nanofluid (GPNF) laden DASC so far is limited to laboratory scale setups or simulation studies. Considering the dearth of outdoor experimental studies, an attempt has been made in the present study to evaluate the thermal performance of Au-NPs (∼40 nm) based nanofluid (∼0.0002 wt%) in full scale DASC. The experiments have been performed at different flow rates under clear sky outdoor conditions in winter season at Jalandhar, India. The maximum collector outlet temperature was measured to be 55 °C with GPNF which is about 7 °C higher than the maximum outlet temperature obtained with de-ionized water as working fluid. Thermal efficiency with GPNF is about 33% higher than de-ionized water at the optimal flow rate of 0.030 kg/s.

Abstract Designing a high-performance hydrofoil is a fundamental challenge for the current turbine blade designers. In this paper, the performance of S1210 hydrofoil, commonly used in the tidal current turbine blades, in presence of (i) Vortex Generators (VGs), and (ii) modified trailing edge is numerically studied. The results show that attaching counter-rotating VGs near the trailing edge of the foil can increase the lift coefficient by 17% and delay the stall angle from 10° to 12°. Constructing a rounded and thicker trailing edge can help to improve the hydrodynamic performance by increasing the lift coefficient by 13.5%. The combination of VGs (located near the trailing edge) and rounded trailing edge can increase the glide ratio significantly. These observations have been explained by plotting the pressure coefficients and velocity profiles at different locations on the foil surface. The findings will be useful to manufacture a stronger blade profile and extract more power from the current turbines that operate at wide current speed variation.

Abstract Many countries produced biodiesel from crude vegetable oil. However, current vegetable oil feedstock to produce biodiesel slow the growth of biodiesel blend implementation due to the high cost of feedstock production. As a result, waste cooking oil (WCO) is claimed to be economic and readily available without cultivation and highly potential feedstock for high yield biodiesel. In this study, Fe-exchanged montmorillonite K10 (Fe-MMT K10) was employed as a catalyst in converting WCO to biodiesel. In comparison, Fe-MMT K10 was able to produce 95.26% biodiesel, which is higher than biodiesel produced using unmodified MMT K10 as catalyst and reaction without catalyst (38.39% and 29.50%, respectively). The full process of biodiesel production was carried out by response surface methodology (RSM) in conjunction with the central composite design (CCD) for statistically optimization and modelling. From the ANOVA, it was found that the production of biodiesel achieved an optimum level of 92.74% biodiesel at 134.07 °C, under a specific optimized condition of 6.32 h reaction time, 4.68 wt% of catalyst and 11.77:1 methanol to oil ratio.