• Energy Research
• 2021-2025close
• 7. Clean energy close
• 11. Sustainability close
• 12. Responsible consumption close
• Energies close

High penetration of renewable energy sources into isolated microgrids (µGs) is considered a critical challenge, as µGs’ operation at low inertia results in frequency stability problems. To solve this challenge, virtual inertia control based on an energy storage system is applied to enhance the inertia and damping properties of the µG. On the other hand, utilization of a phase-locked loop (PLL) is indispensable for measuring system frequency; however, its dynamics, such as measurement delay and noise generation, cause extra deterioration of frequency stability. In this paper, to improve µG frequency stability and minimize the impact of PLL dynamics, a new optimal frequency control technique is proposed. A whale optimization algorithm is used to enhance the virtual inertia control loop by optimizing the parameters of the virtual inertia controller with consideration of PLL dynamics and the uncertainties of system inertia. The proposed controller has been validated through comparisons with an optimized virtual inertia PI controller which is tuned utilizing MATLAB internal model control methodology and with H∞-based virtual inertia control. The results show the effectiveness of the proposed controller against different operating conditions and system disturbances and uncertainties.

To study the heating performance of a solar-assisted cold-water phase-change-energy heat pump system, its heating performance under series and parallel connections is simulated for a community in Harbin, the influence of ice thickness on the different operation modes is analyzed, and the economy of the system is calculated for series and parallel connections in this paper. The results show that the water supply temperature is higher and more uniform in the parallel operation, and more terminal heat is supplied; the ice thickness has more of an influence on the series connection compared to the parallel connection; and the dynamic payback period is 6.72 years for the series connection and 7.28 years for the parallel connection. This case study can serve as a guide for practical engineering application projects and act as a reference for heating and economic data for the promotion of this heat pump system.

Lithium-ion batteries exhibit a dynamic voltage behaviour depending nonlinearly on current and state of charge. The modelling of lithium-ion batteries is therefore complicated and model parametrisation is often time demanding. Grey-box models combine physical and data-driven modelling to benefit from their respective advantages. Neural ordinary differential equations (NODEs) offer new possibilities for grey-box modelling. Differential equations given by physical laws and NODEs can be combined in a single modelling framework. Here we demonstrate the use of NODEs for grey-box modelling of lithium-ion batteries. A simple equivalent circuit model serves as a basis and represents the physical part of the model. The voltage drop over the resistor–capacitor circuit, including its dependency on current and state of charge, is implemented as a NODE. After training, the grey-box model shows good agreement with experimental full-cycle data and pulse tests on a lithium iron phosphate cell. We test the model against two dynamic load profiles: one consisting of half cycles and one dynamic load profile representing a home-storage system. The dynamic response of the battery is well captured by the model.

Installations of an Energy Storage System (ESS) with various functions such as power stabilization of renewable energy, demand management, and frequency adjustment are increasing. In particular, ESS for demand management is being established for high-voltage customers (300 KVA–1000 KVA) who have placed an Auto Section Switch (ASS) at the connection point within the distribution system. However, a power outage may occur in the Power Receiving System (PRS) when a short-circuit fault due to insulation breakdown occurs at the ESS DC side. The reason for this breakdown is that the fault current is reduced by transformer impedance, and the ASS is opened before the DC power fuse. Therefore, using the Graphic Solution Method (GSM), this paper presents an operation algorithm for protection coordination that isolates the fault section by first operating the DC power fuse with a small fault current. Furthermore, fault analysis modeling for a PRS composed of a switchgear section, a main distribution panel, a Power Conditioning System (PCS), a power fuse, and a battery is performed through PSCAD/EMTDC. From the simulation results, it is confirmed that the fault section is quickly isolated, and power outages for high-voltage customers are prevented because the DC power fuse selected by the proposed operation algorithm of protection coordination is opened before the ASS.

In the past decade, inverter-integrated energy sources have experienced rapid growth, which leads to operating challenges associated with reduced system inertia and intermittent power generation, which can cause instability and performance issues of the power system. Improved control schemes for inverters are necessary to ensure the stability and resilience of the power system. Grid-forming inverters dampen frequency fluctuations in the power system, while grid-following inverters can aggravate frequency problems with increased penetration. This paper aims at reviewing the role of grid-forming inverters in the power system, including their topology, control strategies, challenges, sizing, and location. In order to facilitate continued research in this field, a comprehensive literature review and classification of the studies are conducted, followed by research gaps and suggestions for future studies.

Global fossil fuel reserves are declining due to differential uses, especially for power generation. Everybody can help to do their bit for the environment by using solar energy. Geographically, Bangladesh is a potential zone for harnessing solar energy. In March 2021, the renewable generation capacity in Bangladesh amounted to 722.592 MW, including 67.6% from solar, 31.84% from hydro, and 0.55% from other energy sources, including wind, biogas, and biomass, where 488.662 MW of power originated from over 6 million installed solar power systems. Concurrently, over 42% of rural people still suffer from a lack of electricity, where solar energy can play a vital role. This paper highlights the present status of various forms of solar energy progress in Bangladesh, such as solar parks, solar rooftops, solar irrigation, solar charging stations, solar home systems, solar-powered telecoms, solar street lights, and solar drinking water, which can be viable alternative sources of energy. This review will help decision-makers and investors realize Bangladesh’s up-to-date solar energy scenario and plan better for the development of a sustainable society.

Recent developments in micro-grids have led to increased interest in DC distribution due to its high efficiency in distributing energy from renewable energy sources to DC loads. This paper seeks to analyse the performance of AC and DC systems in a relatively large-sized 6 kW PV installation to determine the level of improvement in efficiency provided by DC distribution and to identify methods for further improvement. Baseline annual data for the AC system were collected from a live installation on a national school in Inis Oirr, an island off the west coast of Ireland. The results indicate that usage of a DC distribution system has the potential to reduce system losses by up to 50% as well as the ability for an annual saving in grid energy of 5% compared to the existing AC system. Moreover, the analysis reveals that DC outperforms AC distribution more in spring and autumn, when power consumption is comparable to the system production, but there is less impact in summer, when PV production is significantly higher than demand. These findings provide insights into the benefits of future DC distribution systems in individual buildings and in larger-scale micro-grids.

Vehicle speed prediction plays a critical role in energy management strategy (EMS). Based on the adaptive particle swarm optimization–least squares support vector machine (APSO-LSSVM) algorithm with BP neural network (BPNN), a novel closed-loop vehicle speed prediction system is proposed. The database of a vehicle internet platform was adopted to construct a speed prediction model based on the APSO-LSSVM algorithm. Furthermore, a BPNN is established according to the local high-precision nonlinear fitting relationship between the predicted value and error so as to correct the prediction value. Then, the results are returned to the APSO-LSSVM model for calculating the minimum fitness function, thus obtaining a closed-loop prediction system. Finally, equivalent fuel consumption minimization strategy (ECMS) based EMS was performed. According to the simulation results, the RMSE performance is 0.831 km/h within 5 s, which is over 20% higher than other performances. Additionally, the training time is 15 min within 5 s, which is advantageous over BPNN. Furthermore, fuel consumption increases by 6.95% compared with the dynamic-programming algorithm and decreased by 5.6%~10.9% compared with the low accuracy of speed prediction. Overall, the proposed method is crucial for optimizing EMS as it is not only effective in improving prediction accuracy but also capable of reducing training time.