• Energy Research
• 7. Clean energy close
• AU close
• BE close

Abstract The upward energy demand, along with the depletion of conventional energy sources, demands improved utilization of renewable energy resources. Among all renewable energy resources, solar energy is the most appropriate alternative to conventional energy sources owing to its inexhaustibility and green property. Solar collectors are devices that convert solar radiation into heat or energy. However, the efficiency of the solar collector is still not adequate. The competent step to enhance the efficiency of the solar collector is to use nanofluids. This study is carried out different phases viz. characterization and stabilization while both qualitative and quantitative methods used to evaluate the stability of nanofluids thermophysical properties of Al2O3 and CNC nanofluids such as thermal conductivity measured at four different temperature using KD2 Pro, viscosity and specific heat determined at similar temperature range by viscometer and differential scanning calorimetry respectively. The experiment is executed with a fixed flow rate and in steady-state conditions under extensive solar radiation. The experimental study has revealed that up to 2.48% and 8.46% efficiency of solar collector enhanced by using 0.5% Al2O3 and 0.5% CNC nanofluids respectively. Moreover, nanofluids show good to moderate stability performance. Besides, the thermal conductivity of nanofluids increased while viscosity is in a decreasing trend with increasing temperature. Nanofluids could enhance the efficiency of a flat-plate solar collector.

Abstract Emissions and efficiency of a pellet boiler (40 kW) at nominal load were compared with emissions and efficiency at reduced load, while fired with six biomass pellets. The pellets include reed canary grass ( Phalaris arundinacea ), pectin waste from citrus shells ( Citrus reticulata ), sunflower husk ( Helianthus annuus ), peat, wheat straw ( Triticum aestivum ) and wood pellets. The measurements of emissions comprised of carbon monoxide (CO), nitrogen oxides (NO x ), sulphur oxides (SO x ) and flue dust mass concentrations (using DIN plus and isokinetic sampling techniques). Emissions varied as a function of operational loads, for each type of pellets. The CO emissions were insignificant with reed canary grass (RCG), citrus pectin waste (CPW) and straw pellets at nominal load, however, at reduced load same pellets emitted 1.9, 4.0 and 7.4 times higher CO than wood pellets, respectively. Peat pellets emitted maximum CO at nominal load (4221.1 mgNm −3 , 12.6 times higher than wood pellets) however; at reduced load CO emission was insignificant. The highest NO x emissions were reported with CPW, which were 3.4 and 4.6 times higher than wood pellets at nominal load and reduced load, respectively. Dust emissions were highest with sunflower husk and lowest with RCG pellets, at both operational modes. The best performance was reported with wood pellets, followed by RCG and pectin pellets, however, wood pellets combustion emitted 1.7 and 2.0 times higher dust DIN plus than RCG at nominal and reduced loads, respectively. Not only fuel specific combustion optimization but also operational load specific optimization is essential for efficient use of agro-pellets in this type of boilers.

Co-generation of energy derived from human movement is not new. Intentionally accumulating energy, from mass urban-mobility, provides opportunities to re-purpose power. However, when mass-mobility is predictable, yet not harnessed, this highlights critical gaps in application of interdisciplinary knowledge. This research highlights a novel application of geostatistical modelling for the built environment with the purpose of understanding where energy harvesting infrastructure should be located. The work presented argues that advanced Geostatistical methods can be implemented as an appropriate method to predict probability distribution, density, clustering of populations and mass-population mobility patterns from large-scale online distributed and heterogeneous data sets published by the Australian Urban Research Infrastructure Network. Where clear urban spatio-behavioural relationships of density and movement can be predicted – understanding such patterns supports cross-disciplinary city planning and decision-making. A data-informed – predictive spatial decision-making framework is proposed – facilitating the endeavour of cogenerating kinetic human energy within a prescribed space. This novel proposition could further sustainability strategies for compact living for cities such as in Perth, Western Australia which is increasingly economically and geographically pressured to densify. This research argues that surveillance data elucidate a capacity to interpret and understand impacts of densification strategies, efficacy of CCTV networks in existing and emerging cities.

Abstract In this paper, we investigate distributed thermal-electrochemical modeling of a Lithium-Ion battery cell to include the effect of temperature distribution across the thickness of the cell as a first step to study the module level temperature distribution at high charging rates. Most recent works have focused on lumped thermal models for a Li-Ion cell which ignore any temperature differential across cell thickness. However, even a small temperature differential across cell thickness at the cell level can contribute to significant temperature differential in the thickness direction of stacked-up Li-Ion cells at the module level. Such temperature differential can potentially impact the battery charging control system, especially at high charging rates. Here, the thermal-electrochemical partial differential and algebraic equations for a Li-ion cell are solved via a spatial finite difference method. Simulation results show that the temperature differentials over the cell thickness at the cell level are not insignificant, particularly at high charging rates.

In the current situation with the unprecedented deployment of clean technologies for electricity generation, it is natural to expect that storage will play an important role in electricity networks. This paper provides a qualitative methodology to select the appropriate technology or mix of technologies for different applications. The multiple comparisons according to different characteristics distinguish this paper from others about energy storage systems. Firstly, the different technologies available for energy storage, as discussed in the literature, are described and compared. The characteristics of the technologies are explained, including their current availability. In order to gain a better perspective, availability is cross-compared with maturity level. Moreover, information such as ratings, energy density, durability and costs is provided in table and graphic format for a straightforward comparison. Additionally, the different electric grid applications of energy storage technologies are described and categorised. For each of the categories, we describe the available technologies, both mature and potential. Finally, methods for connecting storage technologies are discussed.

A Wireless Sensor Network (WSN) is comprised of a number of sensor nodes (SNs) that are randomly placed in an open, harsh environment for many applications. Due to the resource-constrained nature of SNs and hostile deployment environments, energy efficiency and security are considered two key factors in designing WSN routing protocols. This paper proposes an Energy Efficient Secure Multipath (EESM) routing protocol to securely construct efficient routes and transmit data packets between SNs and the base station (BS). EESM achieves energy efficiency through minimal task allocation among SNs whereas all computation-intensive tasks such as network information collection, routing table generation, and network maintenance are performed by the BS. The proposed protocol incorporates lightweight security mechanisms including a one-way hash chain, message authentication code, encryption, and clique-based coordinator selection and monitoring schemes to defend against numerous security attacks. Simulation results show that EESM can successfully detect and protect the network against various security attacks such as replay attacks, sybil attacks, sinkhole attacks, spoofing attacks, compromised node attacks, and so on. In terms of energy efficiency, the proposed protocol achieves an up to 37% increase in network lifetime and a 6% increase in throughput over Secure and Energy Efficient Multipath (SEEM) routing, Secure and Reliable Multipath Routing (SRMR), and Reliable and Multipath Encounter Routing (RMER) protocols. The paper implements the protocol in a real environment using Arduino motes to analyze security overheads and network setup time.

Lithium-ion batteries are fast becoming the battery of choice in applications such as electric/hybrid electric vehicles (EV/HEV) and renewable energy systems. This increasing usage demands an improved reliability of the battery systems, which in turn heavily relies on the control and optimization algorithms. Of particular importance is ensuring that each lithium-ion cell within a battery pack remains strictly within an acceptable charge range to avoid untimely degradation of the battery pack. Unfortunately, current battery models make the design of charge equalization circuitry difficult due to their limitations. The aim of this paper is to develop a component-wise control-oriented physics-based battery pack model to facilitate implementation of advanced model-based control and optimization algorithms. In the first stage some existing results are used to obtain a simplified electrochemical ODE model of an individual lithium-ion cell. Then, the cell model is used as the building block of the complete battery pack model. Different charge/discharge scenarios are presented to illustrate the potential of the modeling approach in facilitating the implementation of advanced control and optimization algorithms in improved power equalization and hence prolonging the battery pack lifetime.

After a halt of four years, the n TOF spallation neutron facility at CERN has resumed operation in November 2008 with a new spallation target characterized by an improved safety and engineering design, resulting in a more robust overall performance and e cient cooling. The rst measurement during the 2009 run has aimed at the full characterization of the neutron beam. Several detectors, such as calibrated ssion chambers, the n TOF Silicon Monitor, a Mi- croMegas detector with 10B and 235U samples, as well as liquid and solid scintillators have been used in order to characterize the properties of the neutron uence. The spatial pro le of the beam has been studied with a specially designed \X-Y