• Energy Research
• Restricted close
• engineering and technology close
• AU close
• FI close

In the anodisation of Nb in acidic fluoride solutions or warm aqueous alkali, and in that of Mo in concentrated phosphoric acid, impedance spectroscopy provides evidence that 3D film growth proceeds already during the active–passive transition. Indeed, linear potential dependences of both the inverse of the high-frequency capacitance and of the product of the high-frequency resistance times the steady-state current are observed already below the peak potential. Simultaneously, a pseudo-inductive loop at intermediate frequencies is detected in the impedance spectra. In the present paper, we propose a kinetic model for the interpretation of these data. The model assumes that the metal is covered with a non-stoichiometric oxide containing at least two oxidation states of the cation. The processes of oxidative dissolution of the lower valence cations and their transformation to cations of higher valence, leading to passivation, explain the shape of the I–E curve. These processes are limited by both charge transfer at the film–solution (F/S) interface and transport of cation vacancies through the film. Thickening of the oxide film is assumed to proceed simultaneously, and is limited by transport of oxygen vacancies accelerated by an interfacial charge of cation vacancies.

The International Building Physics Toolbox (IBPT) is a software library developed originally for heat, air and moisture system analysis in building physics. The toolbox is constructed as a modular structure of standard building elements, using the graphical programming language Simulink. To enable development of the toolbox, a common modelling platform is defined: a set of unique communication signals, material database and documentation protocol. The IBPT is an open source and available on the Internet. Any user can utilize, expand and develop the contents of the toolbox. This paper presents structure and essence of the library. Potential applications of the toolbox are illustrated through examples. (C) 2006 Elsevier B.V. All rights reserved.

Wood biomass is turned into industrial fuel through chipping. The efficiency of chipping depends on many factors, including chipper knife wear. Chipper knife wear was determined through a long-term follow-up study, conducted at a waste wood recycling yard. Knife wear determined a sharp drop of productivity (>20%) and a severe decay in product quality. Dry sharpening with a grinder mitigated this effect, but it could not replace proper wet sharpening. Increasing the frequency of wet sharpening sessions determined a moderate increase of knife depreciation cost, but it could drastically enhance machine performance and reduce biomass processing cost. Since benefits largely exceed costs, increasing the frequency of wet sharpening sessions may be an effective measure for reducing overall chipping cost. If the main goal of a chipper operator is to increase productivity and/or decrease fuel consumption, then managing knife wear should be a primary target. (C) 2014 Elsevier Ltd. All rights reserved.

Abstract Thermal energy storage systems for both heat and cold are necessary for many industrial processes. High energy density and high power capacity are desirable properties of the storage. The use of latent heat increases the energy density of the storage tank with high temperature control close to the melting point. Tube in PCM tank is a very promising system that provides high packing factor. This work presents an experimental study of a PCM tank for cold storage applications. Two different configurations and different flow rates of the heat transfer fluid were studied. The effectiveness of the PCM storage system was defined as that of a heat exchanger. The results showed that the heat exchange effectiveness of the system did not vary with time, decreased with increasing flow rate and increased with increasing heat transfer area. The effectiveness was experimentally determined to only be a function of the ratio m ˙ /A. This equation was found to be adequately be used to design a PCM storage system, and a case study is presented. It was shown that the tube in tank design together with a low temperature PCM is suitable as a thermal storage facility for cold storage.

A commercial drum chipper was fed alternately and piecewise with poplar stems and poplar tops, in order to determine the effect of piece size and tree part on machine performance. Chipping stems required most of the available power (231 kW) delivered by the tractor, whereas chipping tops took about half that much. However, productivity was twice as high with stems, compared to tops (i.e. 25 and 11 t h-1 of oven dry wood, respectively). As a consequence, specific fuel consumption per unit product was 15% lower with stems, compared to tops - i.e. 0.61 and 0.72 L m-3, respectively. Mean feeding speed was 0.37 m s-1 for stems and 0.41 m s-1 for tops, but the difference was not significant (p = 0.1677). Productivity and fuel consumption were strongly related to piece size, but tree part had its own additional effect, independent from size and possibly related to form. When chipping tops it is advisable to feed more pieces at a time, in order to partly compensate for the effect of piece size. Operators expecting to chip primarily small-size materials may acquire special chipper versions with wider drums and additional side rollers, for smoother mass feeding. oThe same chipper was tested with poplar stems and tops.oChipping stems resulted in higher productivity and lower fuel consumption.oChipping stems required most of the available tractor power.oChip particle size distribution was about the same for both feedstocks. © 2013 Elsevier Ltd.

In Italy, olive tree groves may offer up to a million tonnes of dry biomass per year as pruning residue. Searching for a cost-effective way to tap this potential, the authors tested a new machine, capable of recovering pruning residue at the same time as pruning. The pre-commercial prototype was tested on four different plots and compared to a simpler tractorbase mechanical pruning unit. The authors conducted detailed time-studies in order to determine machine productivity and residue recovery cost. The integrated machine can treat between 0.2 and 0.6 ha h(-1), producing between 0.33 and 1.03 tonnes of fresh residue hour(-1). Its integrated residue recovery function does not slow the pruning, which actually proceeds faster than with the tractor-base unit, due to the more efficient multiple-disc cutting bar. The marginal cost of residue recovery hovers around 40-45 (sic) fresh tonne(-1). However, the new machine must not be considered just as a biomass harvester, but rather as a mechanical pruning unit with an integrated biomass recovery function. Its main benefit derives from the capacity of performing a very effective mechanical pruning, and the residue recovery function is a secondary benefit yet unavailable on standard pruning machines. Its deployment must be seen in the context of a general effort to modernize olive grove management and to develop an integrated biomass production system, rather than as a further attempt to build a specialised biomass supply chain.

Wet-laying is a mature technology that is applied in large scale for the manufacture of nonwovens, including paper products. However, it usually uses large volumes of water and is energy-intensive. Here we used foam-laying to substantially diminish the volume of water consumed in the formation of fiber networks (5-fold reduction) and to reduce the water content of the nonwovens produced before drying, achieving a reduced energy demand. The prospects of foam-laying were evaluated by comparing foam-laid and wet-laid webs of two types of wood fibers: stiff (lignin-containing) or flexible (lignin-free). Also, the effect of foaming agent type (anionic, cationic, nonionic, and amphoteric) was elucidated. Reference webs were produced by conventional wet-laying, with or without surfactants. Foam-laying was effective in producing a more uniform areal mass distribution (better formation) after wet-pressing. This effect was more evident for the webs synthesized with the flexible fibers. Unlike the layered network structures that were obtained by wet-laying, foam-laid webs exhibited a more felted network, with fibers positioned in the out-of-plane direction. As a result, higher air permeability, web porosity, and light scattering coefficients were measured for the foam-laid webs. The enhanced porosity (lower density) was related to the effect of bubbles during foam-laying and the reduction in surface tension of the foamed-fiber dispersion. The resistance to delamination of low-density webs obtained by foam-laying in the out-of-plane direction was preserved. However, the reduction in tensile strength and modulus of foam-laid webs were determined, owing to the reduced density of the formed structures. Notably, the type of foaming agent used played a minor role as far as the resultant properties of the webs, making the process flexible in terms of the selection of environmentally friendly alternatives. Overall, we compared the physico-mechanical properties of fiber networks formed by web- and foam-laying, depending on fiber type and foaming agent, yielding a property space that is useful in the design of lightweight structures (nonwovens, including paper). The prospects of water and energy savings by foam-laying are the major benefits in the sustainable use of fibers for the assembly of porous materials, such as lightweight nonwoven and paper products.

Abstract The Raman spectra and the Raman parameters have been correlated with changes in the structure of carbon materials, and most of the studies have revealed different development of the Raman spectrum. In the present study micro-Raman spectroscopy was conducted on coal bulk samples and on individual coal macerals (collotelinite, fusinite, and macrinite) from a set of Penn State Coal Bank coals of increasing rank to study the variation of their spectral parameters with rank, and considering coal heterogeneity. The spectral parameters that better correlate with the increasing coal rank, for the coals studied are the full width at half maximum of graphitic band (G: at ∼ 1580 cm− 1), the position of disordered band (D: at ∼ 1350 cm− 1), and the integrated intensity ratio of the D band to G band (ID/IG). With increasing coal rank a narrower G band, a shift of D band to lower wavenumber, and an increase of integrated intensity ratio ID/IG are observed. For each coal, the Raman parameters obtained on fusinites and macrinites are similar and differ from those obtained on coal bulk samples and collotelinites. The variation of the Raman parameters with rank is very well reflected on the analyses of collotelinites.