• Energy Research
• other engineering and technologies close
• BE close
• UA close
• Energies close

The paper presents an experimental study on the formation process of burden surface texture on the blast furnace throat and its influence on the radial distribution of gas flow. The study was performed with the application of blast furnaces equipped with a bell-type charging device using radio-isotope means for the control of burden surface texture (profile) and burden surface level, i.e., gamma locators for burden surface texture. The study was carried out under the conditions of an operating blast furnace in an iron and steel plant using a unique GEOTAPS system for automated control of geometric and temperature parameters of burden material surface on the blast furnace throat. The influence of the surface texture on the gas flow distribution was also investigated. The possibility of a self-stabilization effect for burden surface texture and gas flow in an operating blast furnace under suitable conditions was experimentally proven. As a result of the experimental study performed, four ways of energy-saving technology implementation were determined for the control of blast furnace melting based on the data on the burden surface texture and previously unknown regularities of surface layer formation of burden material on the throat of an operating blast furnace with a bell-type charging device. The main idea of the paper is the development of automated control for the radial distribution of burden material and gas flow using actual or predicted surface texture parameters as important intermediate factors that both describe the process and have a significant simultaneous influence on it.

This paper aims to reconsider prosumers’ role in the power markets in the early stages of their decentralization, accounting for rising self-supply trends, security threats, and economic and regulatory barriers. The development of prosumerism envisages finding the ratio between retail market sales under the feed-in tariff and the net billing mechanism. Within the methodology section, the indicator of prosumer efficiency for electricity generation (EUR/kWh) is proposed based on average consumption/production ratios and consumption/delivery incentives. To support household prosumers, the mentioned incentives on the renewable energy market consider the self-supply cost of electricity, the levelized cost of electricity for small-scale green energy facilities (solar photovoltaic and wind), and transaction costs. This paper evaluates prosumer efficiency under three consumption/production ratio scenarios for Ukrainian households (self-consumption of 40%, 20%, and 100% of green electricity annually generated by a household and selling the leftovers via the feed-in tariff) for 2023. The gradual movement from fixed tariffs for households toward market-based prices promotes the emergence of new related market players and their consolidation in the market. Participation in the organized power market segments is relevant for day-ahead market prices above 130 EUR/MWh, disregarding the households’ tariff rate. The low price caps inhibit the prosumer’s participation in the market, while the transition from the feed-in tariff to net billing significantly promotes their development only under high price caps.

This article presents the possibility of evaluating the efficiency of the heat exchange element with a special stamping plate, which is based on the results of computer simulation. The method is based on a comparative analysis of convective heat transfer models implemented in ANSYS using a k-ε turbulence model. To conduct the study, 3D models of three different types of cavity geometry formed between two heat exchange plates (flat plate, chevron plate, and plate with conical stampings) were built. Simulation was performed by finite element analysis in ANSYS for channels formed by the three types of plates, one of which is a new configuration. The results of hydrodynamic and heat exchange parameters allowed for establishing the efficiency of convective heat exchange for plates of known structures and to compare them with the proposed one. It was found that the plates with conical stamping form the smallest channels through which the fluid moves. The velocity of the coolant is uniform throughout the cross section of the channel and equal to 0.294 m/s; the value of the heat transfer coefficient is the largest of the three models and is 5339 W/(m K), while the pressure drop is 1060 Pa. Taking into account the simulation results, the best heat transfer parameters were shown by the channel formed by plates with conical stamping and the highest pressure drop. To increase the efficiency, indicated by the ratio of heat transfer coefficients to hydraulic resistance, the geometry of the plate with conical stamping was optimized. As a result of optimization, it was found that the optimal geometric parameters of the heat exchange plate with conical stamping were achieved at a 55° inclination angle and 1.5 mm height for the cone. The results of this study can be used in the design of heat exchange elements of new structures with optimal parameters for highly efficient heating of liquid coolants.

The results in this work show the influence of long-term operation on the decomposition of working fluids in eight different organic rankine cycle (ORC) power plants (both heat-led and electricity-led) in a range of 900 kW el to 2 MW el . All case study plants are using octamethyltrisiloxane (MDM) as a working fluid; the facilities are between six to 12 years old. Detailed analyses, including the fluid distribution throughout the cycle, are conducted on one system. All presented fluid samples are analyzed via head space gas chromatography mass spectrometry (HS-GC-MS). Besides the siloxane composition, the influence of contaminants, such as mineral oil-based lubricants (and their components), is examined. In most cases, the original working fluid degrades to fractions of siloxanes with a lower boiling point (low boilers) and fractions with a higher boiling point (high boilers). As a consequence of the analyses, a new fluid recycling and management system was designed and tested in one case study plant (Case Study #8). Pre-post comparisons of fluid samples prove the effectiveness of the applied methods. The results show that the recovery of used working fluid offers an alternative to the purchase of fresh fluid, since operating costs can be significantly reduced. For large facilities, the prices for new fluid range from € 15 per liter (in 2006) to € 22 per liter (in 2013), which is a large reinvestment, especially in light of filling volumes of 4000 liters to 7000 liters per unit. Using the aforementioned method, a price of € 8 per liter of recovered MDM can be achieved.

Electric vehicle (EV) charging stations have become prominent in electricity grids in the past few years. Their increased penetration introduces both challenges and opportunities; they contribute to increased load, but also offer flexibility potential, e.g., in deferring the load in time. To analyze such scenarios, realistic EV data are required, which are hard to come by. Therefore, in this article we define a synthetic data generator (SDG) for EV charging sessions based on a large real-world dataset. Arrival times of EVs are modeled assuming that the inter-arrival times of EVs follow an exponential distribution. Connection time for EVs is dependent on the arrival time of EV, and can be described using a conditional probability distribution. This distribution is estimated using Gaussian mixture models, and departure times can calculated by sampling connection times for EV arrivals from this distribution. Our SDG is based on a novel method for the temporal modeling of EV sessions, and jointly models the arrival and departure times of EVs for a large number of charging stations. Our SDG was trained using real-world EV sessions, and used to generate synthetic samples of session data, which were statistically indistinguishable from the real-world data. We provide both (i) source code to train SDG models from new data, and (ii) trained models that reflect real-world datasets.

In this research, twenty-four high capacity (1360 mAh) NMC622/Si-alloy Li-ion full pouch cells with high silicon-alloy content (55%) are cycle aged under seven different cycling conditions to study the effect of different stressors on the cycle life of Si-anode full cells, among which are the effect of ambient temperature, Depth of Discharge (DoD) and the discharge current. The cells are volumetrically constrained at an optimal initial pressure to improve their cycle life, energy and power capabilities. Furthermore, the innovative test setup allows measuring the developed pressure as a result of repeated (de-)lithiation during battery cycling. This uniquely vast testing campaign on Si-anode full cells allows us to study and quantify independently the influence of different stress factors on their cycle life for the first time, as well as to develop a new capacity fade model based on an observed linear relationship between capacity retention and total discharge capacity throughput.

Nowadays, a car’s engine oil change interval is an essential factor in reducing wear. The correct choice depends on various factors. This study analyzes the changes in the composition of three different engine oils (0W30, 5W30, and 5W40) during the generally accepted oil change interval (15,000 km) in gasoline and diesel cars during the post-warranty period. Commercially available low-level biofuel blends (B7 and E10) were used to power test vehicles in a field test. Engine oil samples were taken every 3000 km for more detailed analysis and tested in an accredited laboratory. The contaminants in the engine oil were determined using several testing methods: spectrometric analysis, gas chromatography, etc. Studies have shown that all used cars have an increase in the number of iron particles, an increased concentration of silicon, and also an increase in the number of nickel particles above 12,000 km. Tests also showed a sharp drop of molybdenum anti-friction additives 4.5 times and a gradual increase in fuel concentration for the Opel Insignia over 12,000 km, but over 9000 km, a significant increase in the concentration of chromium particles. Based on this research results, it is preferable to choose a maintenance interval of no more than 12,000 km for cars during the post-warranty period. In this way, the intensity of engine wear can be reduced due to the loss of adequate protective properties of the engine oil.