• Energy Research
• engineering and technology close
• CA close
• DE close

To mitigate the temperature increase in urban environments and reduce its impact on energy consumption and the quality of the environment, urban retrofitting technologies have been developed and applied worldwide. High albedo in urban surfaces and additional vegetation are the most efficient strategies to accomplish these goals. The objective of this study is to estimate the weight of these strategies, both individually and integrated, on the cooling potential of two Latin American cities. To do this, 36 low and high urban density scenarios were simulated with the ENVI-Met software. The simulation models were calibrated using air temperature curves which were monitored during the summer periods from 2010 to 2013. A Principal Components Analysis was carried out to establish possible associations between the proposed mitigation strategies and then the weight of anthropogenic heat was evaluated according to the configuration. The results show that the integrated mitigation strategies in urban areas -i. e. increase vegetation and albedo on horizontal surfaces- has a great potential to mitigate urban warming, showing a more significant impact on low-density urban configuration. The contribution of anthropogenic heat mainly produced by motorized transport and air conditioning systems, is a crucial input data for the urban microclimate simulations. Its impact on the urban densification processes may cancel out the benefits derived by the application of the mitigation strategies considered.

Abstract This paper uses research-quality, ground measurements of irradiance and temperature that are accurate to ±2% to estimate the electric energy yield of fixed solar modules for utility-scale solar power plants at 18 sites in Saudi Arabia. The calculation is performed for a range of tilt and azimuth angles and the orientation that gives the optimum annual energy yield is determined. A detailed analysis is presented for Riyadh including the impact of non-optimal tilt and azimuth angles on annual energy yield. It is also found that energy yield in March and October are higher than in April and September, due to milder operating temperatures of the modules. A similar optimization of tilt and azimuth is performed each month separately. Adjusting the orientation each month increases energy yield by 4.01% compared to the annual optimum, but requires considerable labour cost. Further analysis shows that an increase in energy yield of 3.63% can be obtained by adjusting the orientation at five selected times during the year, thus significantly reducing the labour requirement. The optimal orientation and corresponding energy yield for all 18 sites is combined with a site suitability analysis taking into account climate, topography and proximity to roads, transmission lines and protected areas. Six sites are selected as having high suitability and high energy yield: Albaha, Arar, Hail, Riyadh, Tabuk and Taif. For these cities the optimal tilt is only slightly higher than the latitude, however the optimum azimuth is from 20° to 53° west of south due to an asymmetrical daily irradiance profile.

Abstract The objective of this work is to evaluate the surge characteristics of an axial compressor operating under surge conditions, by using a hybrid BDF/harmonic balance method. During a surge event, a large amount of backflow occurs in the compressor. Consequently, the airflow oscillates along the axial direction at a low frequency, which can considerably damage the compressor. In this paper, a numerical investigation is performed to examine the effects of the system volume and average mass flow on the surge characteristics of a transonic high speed single stage axial compressor (stage 35) designed and evaluated at the NASA Glenn Center. The results show that the oscillation frequency of the airflow in the compressor generally ranges from 14.32–26.04 Hz during surge conditions, and both the system volume and average mass flow considerably influence the surge characteristics. For a constant average mass flow, as the system volume decreases, the oscillation frequency of the airflow in the compressor increases slightly, while the oscillation amplitude of the exit static pressure decreases significantly, and the maximum static pressure at the outlet remains nearly constant. In the case of a constant system volume, with the decrease in the average mass flow, the oscillation frequency of the airflow in the compressor gradually decreases, and the oscillation amplitude of the exit pressure increases significantly. With a further decrease in the average mass flow, the oscillation frequency stabilizes at a certain point and does not change thenceforth. Furthermore, the surge frequency obtained using the numerical method shows a same tendency with the Helmholtz frequency, but there is a considerable difference between them.

This paper examines and optimizes parameters that affect the air cooling of a Lithium-Ion (Li-Ion) battery, used in Electric Vehicles (EVs). A battery pack containing 150 cylindrical type Li-Ion battery cells in a PVC casing is investigated. An equal number of tubes are used in the pack as a medium to cool the battery by using a fan when the vehicle is stationary or with ambient air when in motion. The parameters affecting the air cooling of battery are studied and optimized by considering their practical constraints. The objective function and Number of Transfer Unit (NTU) are developed. Finally, a genetic algorithm method is employed to optimize the decision variables. Analysing the results shows that NTU can be maximized by increasing the diameter of tubes on the battery and keeping the air velocity in a certain range.

Recycled polylactic acid (PLAr) was reinforced with treated nanocellulosic hemp fibers for biocomposite fabrication. Cellulosic fibers were extracted from hemp fibers chemically and treated enzymatically. Treated nanocellulosic fibers (NCF) were analyzed by Fourier-transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy. Biocomposite fabrication was done with PLAr and three concentrations of treated NCF (0.1%, 0.25%, and 1% (v/v)) and then studied for thermal stability and mechanical properties. Increased thermal stability was observed with increasing NCF concentrations. The highest value for Young’s modulus was for PLAr + 0.25% (v/v) NCF (250.28 ± 5.47 MPa), which was significantly increased compared to PLAr (p = 0.022). There was a significant decrease in the tensile stress at break point for PLAr + 0.25% (v/v) NCF and PLAr + 1% (v/v) NCF as compared to control (p = 0.006 and 0.002, respectively). No significant difference was observed between treatments for tensile stress at yield.

We present the architecture and design of the IANOS scheduling framework. The goal of the new Grid scheduling system is to provide a general job submission framework allowing optimal positioning and scheduling of HPCN applications. The scheduling algorithms used to calculate best-suited resources are based on an objective cost function that exploits information on the parameterization of applications and resources. This standard-based, interoperable scheduling framework comprises four general web services and three modules. The middleware is complemented with one client and one admin console. The implementation is based on proposed Grid and Web services standards (WSRF, WS-Agreement, JSDL, and GLUE). It is agnostic to a specific Grid middleware. The beta version of IANOS has been tested and integrated with UNICORE. The validation of IANOS is in progress by running different types of HPCN applications on a large-scale Grid testbed.

The solution of an electric circuit problem is only valid if the circuit elements have been validly modelled. The iron-cored coil is a common nonlinear circuit element, especially in power system circuits, where the iron core is laminated grain-oriented silicon-iron sheet. This paper attempts to show that eddy-current loss modelling in such a core is at least as important as hysteresis loss modelling, and demonstrates the accuracy of linear modelling of the eddy-current effect. If the circuit analyst has confidence in this complete model he can then decide which aspects of the model can be ignored with impunity when studying such circuit phenomena as ferroresonance, subharmonics and inrush current.

Abstract For 118 million residential housing units in the U.S., there is currently a gap between the potential energy savings that can be achieved through the use of existing energy efficiency technologies, and the actual level of energy savings realized, particularly for the 37% of housing units that are considered residential rental properties. Additional quantifiable benefits are needed beyond energy savings to help further motivate residential property owners to invest in energy efficiency upgrades. This research focuses on assessing the adoption of energy efficient upgrades in U.S. residential housing and the impact on rental prices. Ten U.S. cities are chosen for analysis; these cities vary in size across multiple climate zones, and represent a diverse set of housing market conditions. Data was collected for over 159,000 rental property listings, their characteristics, and their energy efficiency measures listed in rental housing postings across each city. Following an extensive data quality control process, over thirty different types energy efficient features were identified. The level of adoption was determined for each city, ranging from 5.3% to 21.6%. Efficient lighting and appliances were among the most common, with many features doubling as energy efficient and other desirable aesthetic or comfort improvements. Then using propensity score matching and conditional mean comparison methods, the relative impact on rent charged in each city was calculated, which ranged from a 6% to 14.1% increase in rent for properties with energy efficient features, demonstrating a positive economic impact of these features, particularly for property owners. This was further subdivided into five types of energy efficiency upgrade and three housing types. Single family homes generally demanded higher premiums with energy efficient features, however there was not a consistent pattern across the types of efficient upgrades. The results of this work demonstrate that investment in energy efficient technologies has quantifiable benefits for rental property owners in the U.S. beyond just energy savings. This methodology and results can also be used in other cities and by property owners, utility companies, or others, ultimately encouraging further investment and positive economic impact in residential energy efficiency and in turn improving energy and resource conservation in the building sector.

Abstract The price effect of the rising share of renewable electricity, which is called ‘merit-order-effect’, leads to noticeable changes in the German power industry and debates about the electricity market design. This paper estimates the merit-order-effect induced by variable renewable energy in the German-Austrian electricity sector with a multivariate regression model. The research focus lies on the impact of the estimated effects on the marketability of variable renewable electricity generation. The results show a systematic decline of the average market revenues for wind and photovoltaic plants in the period from January 2011 to December 2013. Current market data shows a continuation of this trend into 2016. According to the German long term goals for the use of renewables, wind and solar power will play a crucial role in the future electricity generation mix. If investments in these technologies will be profitable without any regulatory remuneration mechanisms in addition to the market revenues, depends on the further cost degression and the development of the merit-order-effect.