• Energy Research
• Closed Access close
• 6. Clean water close
• 3. Good health close
• 4. Education close
• CA close
• GB close

This study assessed the hand hygiene performance in French nursing homes using the consumption of alcohol-based hand rubs (AHRs) as a surrogate. Nursing homes from the 17 French regions were contacted to collect their AHR consumption and occupancy in 2018 and 2019. A total of 1290 nursing homes from 15 French regions participated in the survey. The estimated median number of hand hygiene actions per resident-day was 1.48 (interquartile range: 1.04-2.03) in 2018 and 1.60 (1.10-2.26) in 2019. A significantly higher AHR consumption was observed in public nursing homes with an infection control team or link nurse.

Abstract In this study, crude cellulose derived from cornstalk, after bleaching, was used as raw material for the synthesis of sodium carboxymethyl cellulose (CMC) by reacting with the cellulose with NaOH and chloroacetic acid at 75 °C for 1.5 h. Effects of alkali dosage, concentration of chloroacetic acid on the physical and chemical properties of the CMC products were investigated. It was revealed that the reactants alkali reagent/chloroacetic acid/cellulose at the molar ratio of 4.6:2.8:1and 4:2.5:1, or at the molar ratio of NaOH/ClCH 2 COOH ≈1.6–1.64, resulted in CMC products of relatively high water solubility. The viscosity-average molecular weight M v of these two CMC products obtained at molar ratios of 4.0:2.5:1 and 4.6:2.8:1 is in the range of 1.94 × 10 4 –2.48 × 10 4 g mol −1 , and the average DS of the two products are 0.57 and 0.85, respectively. As the solute concentration is above 2 wt%, the viscosity of the CMC-water solution exhibits nonlinear (exponential) increasing with increasing the solute concentration (typical of non-Newton fluids).

Among various bioreactors examined in anaerobic digestion and dark fermentation, UASB bioreactor has shown to be a promising alternative. However, mass transfer resistance and biomass washout have been the issues that reported as draw backs of the granular system in the literature. Another problem associated with such a system is its long start-up period as a result of biomass washout and long microbial granulation stage. In this paper, the results obtained from an UASFF bioreactor in methane (AD process) and hydrogen (DF process) production from POME, are presented to assess mass transfer of substrate into the granules and also study the role of internal packing used in the middle part of reactor in the process stability. The value of effectiveness factor, η, for AD and DF processes were calculated to be 0.96 and 0.94, respectively, indicating that there was no mass transfer resistance due to internal and/or external factors. The results showed that the packing material could retain biomass in the reactor and had outstanding contribution in the granulation enhancement. Its role as a supplementing treatment stage was more significant at low HRTs and up-flow velocities.

The operation of centrifugal pumps can generate instabilities and pressure pulsations that may be detrimental to the integrity and performance of the pump. In the present study a numerical investigation of the time variation of pressure within a complete centrifugal pump was undertaken. A range of parameters and three flow rates were investigated and the pulsations were extracted at 15 different locations covering important pump regions. The transient flow results compared reasonably with experimental data obtained in a limited experimental survey and clearly indicated the pump locations experiencing the largest pulsation levels. It was also noted that monitoring pulsations at the top dead centre of the pump volute casing would provide a better indication of internal pump pulsations than monitoring at the discharge.

Abstract Bitumen recovery by steam-solvent coinjection involves the coupled thermal/compositional mechanisms for reduction of bitumen viscosity. Reliable design of such processes requires reservoir flow simulation based on a proper phase-behavior model so that the oleic-phase viscosity near the steam-chamber edge can be modeled reliably. However, the effect of bitumen characterization (e.g., the number of pseudo components used) on steam-solvent coinjection simulation has not been studied in detail, and can be realized only after running multiple reservoir simulations, which is time consuming. There are two main objectives in this paper. One is to develop a reliable method for bitumen characterization by improving the fluid characterization method that was recently developed based on perturbation from n-alkanes (PnA). The other is to develop a novel analytical method for assessing the sensitivity of a particular coinjection simulation to bitumen characterization without having to perform reservoir simulations. A simulation case study is given to validate this analytical method. A proper number of pseudo components for bitumen characterization cannot be determined without considering the effect of phase behavior on the oleic-phase viscosity at chamber-edge conditions in steam-solvent coinjection simulation. Results show that the analytical method developed in this research can detect the sensitivity of recovery simulation to bitumen characterization without performing multiple flow simulations using different sets of fluid models. The PnA-based method developed for bitumen characterization gives reliable predictions of phase behavior for bitumen/solvent mixtures with a small amount of experimental data.

Use of a pilot-scale fixed-film bioreactor was investigated for remediation of bromate contamination within groundwater. Bromate reduction with stoichiometric production of bromide was observed, providing supporting evidence for complete reduction of bromate with no production of stable intermediates. Reduction of 87-90% bromate from an influent concentration of 1.1 mg L(-1) was observed with retention times of 40-80 h. Lower retention times led to decreases in bromate reduction capability, with 11.5% removal at a 10 h retention time. Nitrate reduction of 76-99% from a 30.7 mg L(-1) as NO(3)(-) influent was observed at retention times of 10-80 h, although an increase in nitrite production to 2.7 mg L(-1) occurred with a 10 h retention time. Backwashing was not required, with the large plastic packing media able to accommodate biomass accumulation without decreases in operational efficiency. This study has provided proof of concept and demonstrated the potential of biological bromate reduction by fixed-film processes for remediation of a bromate contaminated groundwater source.

Abstract The development of predictive mathematical models for water management in polymer electrolyte membrane fuel cells requires detailed understanding of water distribution and water transport across the Nafion layer. The anisotropic microstructure of Nafion suggests the measurement of water content and mass transport should be along the fuel cell functional direction, i.e. across the membrane. Non-invasive, high resolution, microscopy measurements of this type are very challenging. We report here the calibration of a minimal mathematical model for diffusive water transport in Nafion against data from high-resolution water content maps determined with a new magnetic resonance imaging methodology developed for this purpose. A mock fuel cell was designed to permit well-controlled wetting and drying boundary conditions. With no chemical potential driving force involved, we assume the water transport behavior will be dominated by diffusion. Moreover we show that, in this context, our model is mathematically equivalent to the traditional permeation models based upon saturation dependent pressure gradients via a capillary pressure ansatz. The non-linear equilibrium water distribution across the Nafion membrane measured in this work suggests a bi-modal diffusivity. The model constructed associates distinct transport behaviors to water contents above and below a critical threshold, consistent with a rearrangement of a micro-structural pore network. The experimental observation and the model prediction agree with the primary features of Weber's model of Nafion, which predicts distinct modes of transport for hydration fronts traversing the through-plane direction of the membrane.

An ecosystem in a cold climate river basin is vulnerable to the effects of climate change affecting permafrost thaw and glacier retreat. We currently lack sufficient data and information if and how hydrological processes such as glacier retreat, snowmelt and freezing-thawing affect sediment and nutrient runoff and transport, as well as N2O emissions in cold climate river basins. As such, we have implemented well-established, semi-empirical equations of nitrification and denitrification within the Soil and Water Assessment Tool (SWAT), which correlate the emissions with water, sediment and nutrients. We have tested this implementation to simulate emission dynamics at three sites on the Canadian prairies. We then regionalized the optimized parameters to a SWAT model of the Athabasca River Basin (ARB), Canada, calibrated and validated for streamflow, sediment and water quality. In the base period (1990-2005), agricultural areas (2662 gN/ha/yr) constituted emission hot-spots. The spring season in agricultural areas and summer season in forest areas, constituted emission hot-moments. We found that warmer conditions (+13% to +106%) would have a greater influence on emissions than wetter conditions (-19% to +13%), and that the combined effect of wetter and warmer conditions would be more offsetting than synergetic. Our results imply that the spatiotemporal variability of N2O emissions will depend strongly on soil water changes caused by permafrost thaw. Early snow freshet leads to spatial variability of soil erosion and nutrient runoff, as well as increases of emissions in winter and decreases in spring. Our simulations suggest crop residue management may reduce emissions by 34%, but with the mixed results reported in the literature and the soil and hydrology problems associated with stover removal more research is necessary. This modelling tool can be used to refine bottom-up emission estimations at river basin scale, test plausible management scenarios, and assess climate change impacts including climate feedback.

The deposition of ash - combustion residues - on superheaters and heat exchanger surfaces reduce their efficiency; this phenomenon was investigated for a large-scale waste-to-energy incineration facility. Over a period of six months, ash samples were collected from the plant, which included the bottom ash and deposits from the superheater, as well as flyash from the convective heat exchanger, the economiser and fabric filters. These were analysed for particle size, unburned carbon, elemental composition and surface morphology. Element partitioning was evident in the different combustion residues, as volatile metals, such as cadmium, antimony and arsenic, were found to be depleted in the bottom ash by the high combustion temperatures (1000+°C) and concentrated/enriched in the fabric filter ash (transferred by evaporation). Non-volatile elements by contrast were distributed equally in all locations (transported by particle entrainment). The heat exchanger deposits and fabric filter ash had elevated levels of alkali metals. 82% of flyash particles from the fabric filter were in the submicron range.