• Energy Research
• Closed Access close
• Restricted close
• Open Source close
• Embargo close
• 12. Responsible consumption close
• 6. Clean water close
• CA close

Abstract In this study, crude cellulose derived from cornstalk, after bleaching, was used as raw material for the synthesis of sodium carboxymethyl cellulose (CMC) by reacting with the cellulose with NaOH and chloroacetic acid at 75 °C for 1.5 h. Effects of alkali dosage, concentration of chloroacetic acid on the physical and chemical properties of the CMC products were investigated. It was revealed that the reactants alkali reagent/chloroacetic acid/cellulose at the molar ratio of 4.6:2.8:1and 4:2.5:1, or at the molar ratio of NaOH/ClCH 2 COOH ≈1.6–1.64, resulted in CMC products of relatively high water solubility. The viscosity-average molecular weight M v of these two CMC products obtained at molar ratios of 4.0:2.5:1 and 4.6:2.8:1 is in the range of 1.94 × 10 4 –2.48 × 10 4 g mol −1 , and the average DS of the two products are 0.57 and 0.85, respectively. As the solute concentration is above 2 wt%, the viscosity of the CMC-water solution exhibits nonlinear (exponential) increasing with increasing the solute concentration (typical of non-Newton fluids).

Abstract Recharging infrastructure (RI) deployment plays a vital role in improving the public recharging availability for transport electrification. Decarbonizing transportation using low-emission electricity requires massive RI network. Even though the consumers are reluctant to purchase electric vehicles (EVs) until RIs are sufficiently placed, the investors are not willing to invest in RIs due to recharging demand uncertainties. Therefore, a scientific planning framework is needed to ensure the sustainable deployment of EV-RIs in complex networks. In this study, a lifecycle thinking-based multi-period infrastructure-planning framework is proposed to develop sustainable public EV-RIs in an urban context. This framework consists of a temporal model to find the dynamic EV-RI demands, a stochastic model to obtain travel distances, and a multi-objective optimization model to select the best desirable capacities and locations for potential EV-RIs. A case study of a typical medium-scale municipality in Canada was assessed using the proposed framework and validated using conventional infrastructure planning scenarios. The geo-processing data, regional travel behaviors, and recharging characteristics were used as model inputs. The results of the case study showed that the proposed framework can be used to estimate multi-period public recharging demands, minimize lifecycle costs, maximize service coverage and infrastructure utilization, and ensure reasonable paybacks compared to conventional planning approaches. Moreover, this framework can be used to compare different investment assistances, which are required in the early stages of the RI deployment process to encourage investors. Furthermore, government and private institutions can use this framework to identify recharging demands, permitting, and developing RIs in the long-run.

Abstract The residential sector accounts for most of energy-consumption in developing countries in the form of traditional energy. The use of commercial energy is nominal and confined mostly to urban areas where fuelwood is already monetized. A model, based on an end-use/process analysis approach, is developed on a spreadsheet, which is capable of simulating scenarios to address issues of increasing traditional energy-demand caused by population growth, sustainable supply capacity of the existing energy resources, potential for development of new and renewable energy resources, technology. This paper is divided into two parts: general energy issues and the modelling approach, and the application of this approach to Nepal in the context of fuelwood-supply sustainability.

AbstractConcrete is a valuable construction material with high mechanical strength and durability, used extensively in the construction industry. It is produced by mixing sand, stones, cement, and water in different proportions depending on the desired quality of the final product. Water reducers are additional chemical ingredients used in concrete to reduce the quantity of water required in the concrete mixture. When added to concrete, water reducers increase the workability and flowability of concrete in the freshly mixed state and improve the mechanical strength and durability of the final hardened product. This review paper describes the different types and applications of concrete water reducers used in the construction industry including their working mechanisms and fluidity effects on concrete properties. It discusses the production of synthetic and bio‐based concrete water reducers and reviews the present challenges involved in the preparation of bio‐based concrete water reducers from renewable resources. © 2023 Society of Industrial Chemistry and John Wiley & Sons Ltd.

Abstract Bitumen recovery by steam-solvent coinjection involves the coupled thermal/compositional mechanisms for reduction of bitumen viscosity. Reliable design of such processes requires reservoir flow simulation based on a proper phase-behavior model so that the oleic-phase viscosity near the steam-chamber edge can be modeled reliably. However, the effect of bitumen characterization (e.g., the number of pseudo components used) on steam-solvent coinjection simulation has not been studied in detail, and can be realized only after running multiple reservoir simulations, which is time consuming. There are two main objectives in this paper. One is to develop a reliable method for bitumen characterization by improving the fluid characterization method that was recently developed based on perturbation from n-alkanes (PnA). The other is to develop a novel analytical method for assessing the sensitivity of a particular coinjection simulation to bitumen characterization without having to perform reservoir simulations. A simulation case study is given to validate this analytical method. A proper number of pseudo components for bitumen characterization cannot be determined without considering the effect of phase behavior on the oleic-phase viscosity at chamber-edge conditions in steam-solvent coinjection simulation. Results show that the analytical method developed in this research can detect the sensitivity of recovery simulation to bitumen characterization without performing multiple flow simulations using different sets of fluid models. The PnA-based method developed for bitumen characterization gives reliable predictions of phase behavior for bitumen/solvent mixtures with a small amount of experimental data.

Abstract Conversion of carbon contained in the solid residues (tars + biochar) derived from urban biomass gasification named herein TC would allow enhancing the yield of carbon species (CO/CO2) in synthetic gas. For this purpose, three low cost materials have been tested as possible catalysts: iron species (reduced Fe), bone meal (BM), and ashes (ash) recovered from biochar complete oxidation. The parametric study used the following as variables: air GHSV, onset of reaction temperature, reaction time to optimize CO/CO2 molar ratio and tar content in the produced gas. Results showed an autocatalytic effect of biochar leading to the catalytic conversion of approximately 78% of tars by the native metals contained in TC. The catalytic effect was further enhanced by adding Fe, BM, and extra ash. Addition of Fe catalyst resulted in significant heat generation (temperature increase of ca. 500 °C) and a twofold decrease in reaction time to consume all the carbon. Use of ash and BM as catalysts exhibit heat generation comparable to Fe, along with an improved reaction time, complete tars conversion and a CO/CO2 molar ratio to above 1.3 in the produced gas.

AbstractCellulose and lignin nanoparticles are high‐value‐added products obtained from lignocellulosic biomasses through several steps of cellulose purification and lignin extraction. These steps drastically reduce the potential feedstock revenue when carried out as stand‐alone methodologies. To increase biomass yields, we describe here a strategy to design a biorefinery focused on producing cellulose and lignin nanoparticles as main products, but also aim to recover and benefit from other biomass components using only water‐based processes. Sequential pressurized liquid extractions and diluted acid and alkaline treatments were carried out to fractionate elephant grass biomass, yielding (for every 100 g of biomass): 30 g of cellulose pulp (converted to 9 g of cellulose nanocrystals and 9 g of cellulose nanofibers); 10 g of lignin (used to produce 8.5 g of stable colloidal lignin nanoparticles by probe‐sonication in water); 7.5 g of extractives (e.g. sterols and phenolics) and 23 g of xylose (converted to 4.1 g of furfural). Alternatively, to allow for the flexible use of the cellulose fraction in the proposed biorefinery, 22 g of glucose could be produced by enzymatic hydrolysis. The results demonstrate that water‐based processes are suitable for a holistic use of biomass, providing a comprehensive set of high‐value‐added co‐products that are renewable and cost‐effective chemical, cosmetic, food, polymer and pharmaceutical solutions.

Abstract The development of predictive mathematical models for water management in polymer electrolyte membrane fuel cells requires detailed understanding of water distribution and water transport across the Nafion layer. The anisotropic microstructure of Nafion suggests the measurement of water content and mass transport should be along the fuel cell functional direction, i.e. across the membrane. Non-invasive, high resolution, microscopy measurements of this type are very challenging. We report here the calibration of a minimal mathematical model for diffusive water transport in Nafion against data from high-resolution water content maps determined with a new magnetic resonance imaging methodology developed for this purpose. A mock fuel cell was designed to permit well-controlled wetting and drying boundary conditions. With no chemical potential driving force involved, we assume the water transport behavior will be dominated by diffusion. Moreover we show that, in this context, our model is mathematically equivalent to the traditional permeation models based upon saturation dependent pressure gradients via a capillary pressure ansatz. The non-linear equilibrium water distribution across the Nafion membrane measured in this work suggests a bi-modal diffusivity. The model constructed associates distinct transport behaviors to water contents above and below a critical threshold, consistent with a rearrangement of a micro-structural pore network. The experimental observation and the model prediction agree with the primary features of Weber's model of Nafion, which predicts distinct modes of transport for hydration fronts traversing the through-plane direction of the membrane.

An ecosystem in a cold climate river basin is vulnerable to the effects of climate change affecting permafrost thaw and glacier retreat. We currently lack sufficient data and information if and how hydrological processes such as glacier retreat, snowmelt and freezing-thawing affect sediment and nutrient runoff and transport, as well as N2O emissions in cold climate river basins. As such, we have implemented well-established, semi-empirical equations of nitrification and denitrification within the Soil and Water Assessment Tool (SWAT), which correlate the emissions with water, sediment and nutrients. We have tested this implementation to simulate emission dynamics at three sites on the Canadian prairies. We then regionalized the optimized parameters to a SWAT model of the Athabasca River Basin (ARB), Canada, calibrated and validated for streamflow, sediment and water quality. In the base period (1990-2005), agricultural areas (2662 gN/ha/yr) constituted emission hot-spots. The spring season in agricultural areas and summer season in forest areas, constituted emission hot-moments. We found that warmer conditions (+13% to +106%) would have a greater influence on emissions than wetter conditions (-19% to +13%), and that the combined effect of wetter and warmer conditions would be more offsetting than synergetic. Our results imply that the spatiotemporal variability of N2O emissions will depend strongly on soil water changes caused by permafrost thaw. Early snow freshet leads to spatial variability of soil erosion and nutrient runoff, as well as increases of emissions in winter and decreases in spring. Our simulations suggest crop residue management may reduce emissions by 34%, but with the mixed results reported in the literature and the soil and hydrology problems associated with stover removal more research is necessary. This modelling tool can be used to refine bottom-up emission estimations at river basin scale, test plausible management scenarios, and assess climate change impacts including climate feedback.