• Energy Research
• Restricted close
• 13. Climate action close
• 6. Clean water close
• CN close
• CA close

Hot water heat stores with stratification are a common technology used in solar energy systems and reuse of waste heat. Adding a PCM module at the top of the water tank would give the system higher storage density, and compensate heat loss in the top layer. The work presented here includes experimental results and numerical simulation of the system using an explicit finite-difference method. Experiments and simulations were carried out using different cylindrical PCM modules. With only 1/16 of the volume of the store being PCM, 3/16 of water at the top of the store was held warm for 50% to 200% longer and the average energy density was increased by 20% to 45%. Furthermore, these 3/16 of water were reheated by the heat from the module after being cooled down in only 20 min.

Using recycled rubber crumbs as drainage layer in extensive green roofs have high potential to reduce the heating and cooling loads in buildings over traditional materials used as drainage layer, such as pozzolana gravel. However, the environmental impact due to the life cycle should be analyzed to assess its environmental benefit. This paper evaluates the environmental performance of green roofs in which the drainage layer is made of rubber crumbs, a recycled material the use of which is still experimental for this purpose. In this paper Life Cycle Assessment (LCA) is applied to compare the environmental impact of four constructive systems, two extensive green roofs without insulation layer and with different drainage materials, e a recycled material, rubber crumbs, and a conventional one, pozzolana gravel -, in front of two conventional flat roofs, with and without thermal insulation (polyurethane), built in an experimental set-up consisting of four monitored house-like cubicles, located in Mediterranean continental climate (Lleida, Spain). The LCA considered the production, construction, operational, and disposal phases of the roofs, according to UNE-EN 15643-2. The operational phase was carried out using data measured in the experimental set-up, considering heating and cooling energy consumptions in the winter and summer period, respectively.

Artículos en revistas Energy transportation costs typically make up a quarter of consumers? electricity bills, and most of this amount (90% in the United Kingdom, 75% in Brazil and Spain, and 60% in India, for example) is due to energy transportation through the distribution network. This cost could escalate over the next few decades as distributed energy resources are expected to grow substantially in response to the financial incentives many governments have created for renewable and efficient generation to meet their CO2 reduction targets. info:eu-repo/semantics/publishedVersion

In this work, a novel enhanced deep borehole heat exchanger (EDBHE) was proposed to improve heat extraction efficiency based on the jet grouting method. By means of this technology, a soilcrete zone with high thermal conductivity was built near the wellbore. To analyze the feasibility and efficiency of this method, we firstly constructed a validated deep borehole heat exchanger (DBHE) model based on the field experimental data. Numerical simulations were carried out to investigate the 30-year production performance of EDBHE. Results demonstrated that the jet grouting method is an efficient way for improving thermal output of DBHE. It is evaluated that the average annual heat production rate over a 30-year heating period of EDBHE is 463.2 kW, which is 1.27 times as that of DBHE. Sensitivity analyses indicate that the heat production rate and outlet temperature mainly depend on the height and radius of the artificial soilcrete zone. However, thermal output is not sensitive to thermal conductivity of the soilcrete zone due to the higher thermal resistance of the geological formation. For the experimental site used in this work, the recommended height, radius, and thermal conductivity of the soilcrete are 1000 m, 1.0 m, and 50 W/m °C, respectively.

Major reorganizations in climate and tectonic regime occurred in East Asia during the Pleistocene, resulting in large-scale environmental changes. In this paper a detailed geochemical and mineralogical record of these changes is presented from a distal alluvial fan sedimentary sequence in the northern Weihe Basin. We established that, in addition to glacial-interglacial variation, there are three distinctly different units deposited over the past 1 m.y. These units are the result of variations in the overall tectonic regime in the northern Weihe Basin. Fine-grained detrital minerals were predominantly delivered during colder climatic periods, whereas evaporative minerals were dominantly deposited during the warmer, interglacial periods, probably as a result of strong seasonal contrast. This compositional variation demonstrates the importance of climate control on hinterland erosion, surface runoff, chemical weathering and evaporation. Al-normalized ratios of indicative major elements relative to average loess composition, indicate important variations in sedimentary processes, mostly related to sediment flux. Si-enrichment is an index for past flooding events, while Fe enrichment, just like K and Ti, reflects influx of clays. In contrast, Ca and Mn are strongly enriched throughout the core, associated with the authigenic precipitation of carbonates, especially during interglacial periods. The lower (~ 1000–690 ka) and upper (~ 330–0 ka) units of the core are characterized by relative intense and frequent flooding, which coincided with extensive ponding in the study area. In the middle unit (~ 690–330 ka) increased salinity levels caused by evaporation, as reflected in the high Sr/Ca ratio and dolomite abundance, led to increased carbonate precipitation. Simultaneously, the increased influx of fine sediments indicates increased clay production in the source area as a result of a more intense summer monsoon strength after 600 ka. © 2017 Elsevier B.V.

Abstract This review summarizes and organizes the literature on life cycle assessment (LCA), life cycle energy analysis (LCEA) and life cycle cost analysis (LCCA) studies carried out for environmental evaluation of buildings and building related industry and sector (including construction products, construction systems, buildings, and civil engineering constructions). The review shows that most LCA and LCEA are carried out in what is shown as “exemplary buildings”, that is, buildings that have been designed and constructed as low energy buildings, but there are very few studies on “traditional buildings”, that is, buildings such as those mostly found in our cities. Similarly, most studies are carried out in urban areas, while rural areas are not well represented in the literature. Finally, studies are not equally distributed around the world.

Low temperature sensitive products transport and storage is an issue worldwide due to changes of the lifestyle population increase. Thermal energy storage (TES) is nowadays one of the most feasible solutions in facing the challenge of achieving energy savings. Many researchers have investigated energy efficiency of different cold units by applying TES systems using phase change materials (PCM). This paper provides an overview of the existing Spanish and European potential energy savings and CO2 mitigation by incorporating TES systems to cold storage and transportation systems. Data on energy savings were compiled from different case studies. Results depend on the scenarios studied and the extent of TES systems implementation; in the case of Europe for instance, yearly CO2 emissions may be cut down between 5% and 22% in reference to 2008 CO2 emissions from cold production considering that the proposed implementation of PCM TES in the case studies found in the literature is done.

Abstract In this study, we investigate the driving forces behind the changes in residential energy consumption (REC) in China’s urban and rural areas over the 2001–2012 period. Based on the logarithmic mean Divisia index method, the REC changes are decomposed into seven driving forces, which are climate change, energy price, energy expenditure mix, energy cost share (in total expenditure), expenditure share (in income), per capita income and population effects. According to the results, climate effect due to increasing days with abnormal temperature, energy cost share effect characterized by more expenditure to be paid for energy use, income effect describing constant income growth in the residential sector definitely increase REC in both urban and rural areas. In contrast, energy prices and energy expenditure mix effects negatively contribute to the REC increase, respectively because of the increase in energy prices and the transition from the low-priced energy to high-priced energy. Expenditure share and population effects play opposite roles in urban and rural areas, and the reasons and implications are analysed in depth.