• Energy Research
• other engineering and technologies close
• CN close
• AU close
• EU close
• EG close

AbstractDecarbonising the energy system requires high shares of variable renewable generation and sector coupling like power to heat. In addition to heat supply, heat pumps can be used in future energy systems to provide flexibility to the electricity system by using the thermal storage potential of the building stock and buffer tanks to shift electricity demand to hours of high renewable electricity production. Bridging the gap between two methodological approaches, we coupled a detailed building technology operation model and the open-source energy system model Balmorel to evaluate the flexibility potential that decentral heat pumps can provide to the electricity system. Austria in the year 2030 serves as an example of a 100% renewable-based electricity system (at an annual national balance). Results show that system benefits from heat pump flexibility are relatively limited in extent and concentrated on short-term flexibility. Flexible heat pumps reduce system cost, CO2 emissions, and photovoltaics and wind curtailment in all scenarios. The amount of electricity shifted in the assessed standard flexibility scenario is 194 GWhel and accounts for about 20% of the available flexible heat pump electricity demand. A comparison of different modelling approaches and a deterministic sensitivity analysis of key input parameters complement the modelling. The most important input parameters impacting heat pump flexibility are the flexible capacity (determined by installed capacity and share of control), shifting time limitations, and cost assumptions for the flexibility provided. Heat pump flexibility contributes more to increasing low residual loads (up to 22% in the assessed scenarios) than decreasing residual load peaks. Wind power integration benefits more from heat pump flexibility than photovoltaics because of the temporal correlation between heat demand and wind generation.

Abstract The accurate information of the thermal stresses and temperature in isotropic elastic solids is the key for many engineering applications. At present the classical linear coupled theory of thermoelasticity deduced with the assumptions of small temperature changes is widely used to solve the thermoelastic problems in engineering. In this paper, to describe the thermoelastic behavior in isotropic solids undergoing large temperature changes more accurately, the novel coupled models of thermoelasticity and the corresponding finite element models have been presented explicitly and validated by experimental measurement. The effect of large temperature changes on the solutions of thermoelastic problems is discussed. For the heat transfer process, if the isotropic elastic solids will expand when heated and contract when cooled and the condition d E E d T · σ i j E − δ i j 1 − 2 ν α 0 can be met in the context of small deformations, the effect of large temperature changes can be regarded as increasing the specific heat. The proposed models are applied to solve two thermoelastic problems. From the obtained numerical results, the effect of large temperature changes will increase with the amplitude of temperature change and may be considerably even when the temperature changes slowly.

Hydrothermal liquefaction (HTL) is an effective way to treat solid wastes with high moisture content. The co-hydrothermal liquefaction (co-HTL) experiments of oily scum and poplar sawdust biochar at the different hydrothermal temperatures were performed in this work. The changes of the appearance and components of the liquid products were comprehensively studied. The results showed that the addition of biochar into oily scum significantly reduced the moisture content of the residue hydrochars obtained after co-HTL. As the hydrothermal temperature increased, the liquid products obtained from co-HTL turned clearer and lighter in color, and the recovery rate of the liquid products significantly increased. The co-HTL of bi-ochar and oily scum could effectively improve the liquid quality and enhance the recovery rate of hydrochars. The carbon numbers of the liquid products obtained from co-HTL were concentrated in C5-C11, which were main compositions of gas-oline. This work can provide basic data and theoretical reference for oily scum efficient treatment and engineering practice.

High penetration of renewable energy sources into isolated microgrids (µGs) is considered a critical challenge, as µGs’ operation at low inertia results in frequency stability problems. To solve this challenge, virtual inertia control based on an energy storage system is applied to enhance the inertia and damping properties of the µG. On the other hand, utilization of a phase-locked loop (PLL) is indispensable for measuring system frequency; however, its dynamics, such as measurement delay and noise generation, cause extra deterioration of frequency stability. In this paper, to improve µG frequency stability and minimize the impact of PLL dynamics, a new optimal frequency control technique is proposed. A whale optimization algorithm is used to enhance the virtual inertia control loop by optimizing the parameters of the virtual inertia controller with consideration of PLL dynamics and the uncertainties of system inertia. The proposed controller has been validated through comparisons with an optimized virtual inertia PI controller which is tuned utilizing MATLAB internal model control methodology and with H∞-based virtual inertia control. The results show the effectiveness of the proposed controller against different operating conditions and system disturbances and uncertainties.

Environment-friendly treatment of sewage sludge has become tremendously important. Conversion of sewage sludge into energy products by environment-friendly conversion process, with its energy recovery and environmental benefits, is being paid significant attention. Direct liquefaction of sewage sludge into bio-oils with supercritical water (SCW) was therefore put forward in this study, as de-water usually requiring intensive energy input is not necessary in this direct liquefaction. Supercritical water may act as a strong solvent and also a reactant, as well as catalyst promoting reaction process. Experiments were carried out in a self designed high-pressure reaction system with varying operating conditions. Through orthogonal experiments, it was found that temperature and residence time dominated on bio-oil yield compared with other operating parameters. Temperature from 350 to 500°C and reaction residence time of 0, 30, 60min were accordingly investigated in details, respectively. Under supercritical conversion, the maximum bio-oil yield could achieve 39.73%, which was performed at 375°C and 0min reaction residence time. Meanwhile, function of supercritical water was concluded. Fuel property analysis showed the potential of bio-oil application as crude fuel.