• Energy Research
• 7. Clean energy close
• CN close
• GB close
• ES close
• CA close

The industrial sector accounts for 17% of end-use energy in the UK, and 54% globally. Therefore, there is substantial scope for simulating and assessing potential energy retrofit options for industrial buildings. Building Energy Modelling (BEM) applied to industrial buildings poses a complex but important opportunity for reducing global energy demand, due to years of renovation and expansion. Large and complex industrial buildings make modelling existing geometry for BEM difficult and time consuming. This paper presents a potential solution for quickly capturing and processing as-built geometry of a factory to be utilized in BEM. Laser scans were captured from the interior of an industrial facility to produce a Point Cloud. The existing capabilities of a Point Cloud processing software were assessed to identify the potential development opportunities to automate the conversion of Point Clouds to building geometry for BEM applications. In conclusion, scope exists for increasing the speed of 3D geometry creation of an existing industrial building for application in BEM and subsequent thermal simulation.

Abstract Space–time kinetics calculations for CANDU ® 1 reactors are routinely performed using the Improved Quasistatic (IQS) method. The IQS method calculates kinetics parameters such as the effective delayed-neutron fraction and generation time using adjoint weighting. In the current implementation of IQS, the direct flux, as well as the adjoint, is calculated using a two-group cell-homogenized reactor model which is inadequate for capturing the effect of the softer energy spectrum of the delayed neutrons. Additionally, there may also be fine spatial effects that are lost because the intra-cell adjoint shape is ignored. The purpose of this work is to compare the kinetics parameters calculated using the two-group cell-homogenized model with those calculated using lattice-level fine-group heterogeneous adjoint weighting and to assess whether the differences are large enough to justify further work on incorporating lattice-level adjoint weighting into the IQS method. A second goal is to evaluate whether the use of a fine-group cell-homogenized lattice-level adjoint, such as is the current practice for Light Water Reactors (LWRs), is sufficient to capture the lattice effects in question. It is found that, for CANDU lattices, the generation time is almost unaffected by the type of adjoint used to calculate it, but that the effective delayed-neutron fraction is affected by the type of adjoint used. The effective delayed-neutron fraction calculated using the two-group cell-homogenized adjoint is 5.2% higher than the “best” effective delayed-neutron fraction value obtained using the detailed lattice-level fine-group heterogeneous adjoint. The effective delayed-neutron fraction calculated using the fine-group cell-homogenized adjoint is only 1.7% higher than the “best” effective delayed-neutron fraction value but is still not equal to it. This situation is different from that encountered in LWRs where weighting by a fine-group cell-homogenized adjoint is sufficient to calculate the correct effective delayed-neutron fraction. It is concluded that lattice-level weighting with a detailed fine-group heterogeneous adjoint is desirable for the correct calculation of the effective delayed-neutron fraction in CANDU lattices.

Abstract Knocking combustion for spark-ignition engine is related to auto-ignition of a portion of the unburned fuel-air mixture. In this investigation, the detailed chemical kinetic mechanism was engaged to numerically study the auto-ignition characteristics of hydrogen-enriched methane under engine-relevant conditions. Compared with the experimental data, the USC Mech 2.0 mechanism obtained the closest agreement, and it was adopted in the sensitivity analysis, the rate of production (ROP) analysis and the reaction pathway analysis. Results showed that at high temperature and high pressure, the ignition delay times (IDs) of CH4/H2 fuel blends reduce significantly (by two orders of magnitude at most) with rising hydrogen fraction, but the decline rate is not so obvious (within 37.3%) at low temperature. The sensitivity analysis indicated that at high temperature the reaction (R1) and reactions (R2, R3) promote each other while at low temperature only the reaction (R3) unilaterally facilitates the reaction (R12). The ROP analysis implied that the decrease of IDs of methane by hydrogen addition is realized through increasing the H, O, and OH radical production. Interestingly, the IDs for CH4/H2 fuel blends show different trends at different temperature, which decrease (by 47.5% at most) at low temperature but increase (by 132.7% at most) at high temperature as the equivalence ratio rises. The sensitivity analysis showed that the ignition kinetics for CH4/H2 fuel blends more depend on the CH4 concentration at low temperature but oxygen concentration at high temperature. This investigation not only supplements the fundamental combustion studies of CH4/H2 fuel blends in elevated pressures, but also reveals the influence mechanism of hydrogen addition and equivalence ratio on the IDs of CH4/H2 fuel blends at high pressure. More importantly, it may offer fundamental insights for the control of knocking combustion of spark-ignition (SI) engine.

To meet power quality requirements, it is necessary to classify and identify the power quality of the power grid connected with renewable energy generation. S-transform (ST) is an effective method to analyze power quality in time and frequency domains. ST is widely used to detect and classify various kinds of non-stationary power quality disturbances. However, the long taper and scaling criteria of the Gaussian window in standard ST (SST) will lead to poor time domain resolution at low frequency and poor frequency resolution at high frequency. To solve the discrete side effects, it is necessary to select the optimal window function to locate the time frequency accurately. This paper proposes a modified ST (MST) method. In this method, an improved window function of energy concentration in time-frequency distribution is introduced to optimize the shape of each window function. This method determines the parameters of Gaussian window to maximize the product of energy concentration in a time-frequency domain within a given time and frequency interval, so as to improve the energy concentration. The result shows that compared with the SST with Gaussian window, ST based on the optimally concentrated window proposed in this paper has better energy concentration in time-frequency distribution.

Abstract Two office layouts with high and low levels of thermal control were compared, respectively traditional cellular and contemporary open plan offices. The traditional Norwegian practice provided every user with control over a window, blinds, door, and the ability to adjust heating and cooling. Occupants were expected to control their thermal environment to find their own comfort, while air conditioning was operating in the background to ensure the indoor air quality. In contrast, in the British open plan office, limited thermal control was provided through openable windows and blinds only for occupants seated around the perimeter of the building. Centrally operated displacement ventilation was the main thermal control system. Users’ perception of thermal environment was recorded through survey questionnaires, empirical building performance through environmental measurements and thermal control through semi-structured interviews. The Norwegian office had 35% higher user satisfaction and 20% higher user comfort compared to the British open plan office. However, the energy consumption in the British practice was within the benchmark and much lower than the Norwegian office. Overall, a balance between thermal comfort and energy efficiency is required, as either extreme poses difficulties for the other.

Abstract The Renewable energy power generation capacity has been rapidly increasing in China recently. Meanwhile, the contradiction between power supply and demand is becoming increasingly more prominent due to the intermittence of renewable energies. On the other hand, on the mitigation of carbon dioxide (CO2) emissions in China needs immediate attention. Power-to-Gas (PtG), a chemical energy storage technology, can convert surplus electricity into combustible gases. Subsurface energy storage can meet the requirements of long term storage with its large capacity. This paper provides a discussion of the entire PtG energy storage technology process and the current research progress. Based on the comparative study of different geological storage schemes for synthetic methane, their respective research progress and limitations are noted. In addition, a full investigation of the distribution and implementation of global PtG and CO2 capture and storage (CCS) demonstration projects is performed. Subsequently, the opportunities and challenges of the development of this technology in China are discussed based on techno-economic and ecological effects analysis. While PtG is expected to be a revolutionary technology that will replace traditional power systems, the main issues of site selection, energy efficiency and the economy still need to be adequately addressed. Additionally, based on the comprehensive discussion of the results of the analysis, power-to-gas and subsurface energy storage implementation strategies, as well as outlook in China are presented.

The power transformer is important equipment for energy conversion and transmission in the power grid and its failure will bring significant economic losses to the power system. The hot-spot temperature is a primary factor affecting the reliability and service life of power transformers. In order to calculate the temperature distribution of oil-immersed transformer windings accurately, it is required to solve a multi-physical problem, in which the magnetic field and the fluid-temperature field are coupled. In the simulation of multi-physical field of transformer, many studies usually omit the turn-to-turn insulation of windings to simplify the oil-immersed transformer model. The purpose of this paper is to investigate the effect of the turn-to-turn insulation of windings in oil-immersed transformers on the simulation results. First, a 2D axisymmetric transformer model was established in ANSYS to study the effect of low-voltage winding turn-to-turn insulation on the magnetic field simulation results. The differences of eddy current losses in the simulation were also calculated in terms of the magnetic field simulation results. It is found that the turn-to-turn insulation does not affect the magnetic field distribution in evidence from the simulation results. Besides, the values of the magnetic field and eddy current loss appear significant differences only at both ends of the low-voltage winding. Second, the fluid-temperature field of the transformer was solved in Fluent and the turn-to-turn insulation was the controlled objective in the solution process with consideration of the difference in winding losses. The simulation results show that the turn-to-turn insulation of the winding does not change the oil flow distribution in simulation. The simulation model with turn-to-turn insulation appears a gradient in the temperature distribution of the discs and a rise in the overall temperature distribution. Moreover, this paper analyzes the possible reasons for the differences in the simulation results of the magnetic and temperature fields caused by the turn-to-turn insulation. Some results and conclusions in this paper can be used in related studies and designs.

Oil shale is a kind of potential alternative energy source for petroleum and has attracted the attention of energy researchers all over the world. Borehole hydraulic mining has more prominent advantages than both conventional open-pit mining and underground mining. It is very important to attempt to use the borehole hydraulic mining method to exploit underground oil shale. The nozzle is the key component of borehole hydraulic mining and reasonable mining parameters are also crucial in exploiting underground oil shale efficiently. The straight cone nozzle and the oil shale of Huadian area will be taken as the research objects. The self-developed, multifunctional, experimental device can test both the jet’s performance as well as the breaking of oil shale by the high-pressure water jet using the straight cone nozzle and varying structural parameters. Comprehensive analysis of the results of an orthogonal experimental design, including range analysis and variance analysis, demonstrate the optimal structural parameters of a straight cone nozzle as follows: the outlet diameter is 4 mm, the length to diameter ratio is 2.5, and the contraction angle is 60°. In addition, in order to maximize the efficiency of borehole hydraulic mining for Huadian oil shale, the non-submerged jet should be placed parallel to the oil shale bedding. These results can provide scientific and valuable references for borehole hydraulic mining of oil shale.