• Energy Research
• 7. Clean energy close
• 11. Sustainability close
• 12. Responsible consumption close
• CN close
• IT close
• EU close

By using a liquid desiccant ventilation system for dehumidification and an air-handling unit for cooling, the liquid desiccant cooling system (LDCS) system became a promising alternative for traditional technology. Solar thermal energy is suitable to deal with the heat requirement of LDCS in buildings, especially in the areas with abundant solar radiation. The energy saving of solar-assisted liquid desiccant air-conditioning system is significantly affected by various operation conditions, and multi-parameter optimization was necessary to improve the system applicability. In this paper, we investigated the impact of five main parameters on the system performance via self-developed system modelling, including the solution mass flow rate, concentration, cooling tower flow rate, and solar water flow rate and installation area of solar collector. A typical commercial building in Hong Kong was selected as a case study, which air-conditioning load was obtained by Energy-plus. The results indicated that the installation area of solar collector showed the greatest impact, and the effect of heating water flow rate was also important. The effect of desiccant flow rate was significant, but the influence of solution concentration was slight. Then, the multi-parameter optimization was conducted for obtaining a maximum annual electricity saving rate based on the Multi-Population Genetic Algorithm. The optimized installation area of solar collector was 72 m2, and the heating water flow rate was 0.66 kg/s. The optimized solution flow rate was 0.17 kg/s. The required cooling water flow rate was around 0.8 kg/s.

Dataset supporting publication: “A novel ROM methodology to support the estimation of the energy savings under the Measurement and Verification protocol” (publication available for download: GEOFIT Zenodo) Datasets resultant from simulation of the integrated system into buildings. Conference paper presented in IBPSA-England Building Simulation and Optimisation Conference 2020 This paper presents a novel Reduced Order grey box Model (ROM) methodology, based on a Resistor-Capacitor (RC) network, which supports the creation of the baseline energy consumption and the estimation of energy savings due to Energy Conservation Measures (ECMs) under the Measurement and Verification protocol. Within this scope, a description of the RC network, including a calculation of the parameters’ needed to execute the ROM, are presented. This ROM methodology is demonstrated on an educational building located in Sant Cugat, Spain as part of the H2020 GEOFIT project. The results presented in this paper demonstrate that the ROM is sufficiently accurate for the creation of the baseline energy consumption and for estimating the energy savings of different ECMs.

This dataset was prepared by TNO as a contribution to the H2020 project CHE and the H2020 project VERIFY. The basis is a high-resolution (~1x1 km) emission inventory providing CO2 and CO (from fossil fuels and biofuels separately) over western Europe (2ºW - 19ºE, 47ºN - 56ºN). The reported emissions by European countries to UNFCCC (CO2) and to EMEP/CEIP (CO) have been used and where needed gap-filled or replaced with emission data from the GAINS model. These country-level emissions are disaggregated in space using a consistent spatial distribution methodology, whereas large point sources are listed with their exact locations. This approach is similar to the one described by Kuenen et al., (ACP, 2014). Emissions are reported per GNFR sector, with an extra split for road transport. The emission grids that are part of this dataset are a variation on the base grid, representing the uncertainty in the emission data. Each grid is equally plausible. The grids have been created using a Monte Carlo approach. The uncertainties in the underlying data used to create the base grid (emissions: activity data and emission factors, spatial proxies) have been collected (either from country reports or based on expert judgement). Through the Monte Carlo simulation these uncertainties, taking into account error correlations between some sub-sectors, are combined to create ten new emission grids. The spread in emissions between these emission maps gives an indication of the uncertainty in the emissions. The grid files (in .csv and .nc format) contain annual total emissions per grid cell for the year 2015. A separate file has been prepared for each ensemble member in the Monte Carlo simulation (indicated with M). The unit in the files is kg/yr. A detailed description of the Monte Carlo simulation is presented in: Super, I., Dellaert, S. N. C., Visschedijk, A. J. H., and Denier van der Gon, H. A. C.: Uncertainty analysis of a European high-resolution emission inventory of CO2 and CO to support inverse modelling and network design, Atmos. Chem. Phys. Discuss., https://doi.org/10.5194/acp-2019-696, in review, 2019. N.B. It is important to note that 10 maps are not sufficient to describe the sometimes complex uncertainty structures, for example in the case of lognormal uncertainty distributions. The interpretation of the uncertainty based on these 10 maps should therefore be done with care. NB. Despite efforts to prevent negative emissions to occur in the grid maps, some negative values are still present. In local studies this might cause some issues, and we recommend to set negative emissions to zero in those cases.

Three data files are provided for Case Study 1 in the openENTRANCE project: Full_potential.V9.csv, metaData.Full_Potential.csv, and acheivable_NUTS2_summary.csv. The data covers 10 residential devices on the NUTS2 level for the EU27 + UK +TR + NO + CH from 2020-2050. The devices included are storage heater, water heater with storage capabilitites, air conditiong, heat circulation pump, air-to-air heat pump, refreigeration (includes refrigerators and freezers), dish washer, washing machine, and tumble drier. Full_potential.V9.csv shows the NUTS2 level unadjusted loads for residential storage heater, water heater, air conditiong, circulation pump, air-to-air heat pump, refreigeration (includes refrigerators and freezers), dish washer, washing machine, and tumble drier using representative hours from 2020-2050. The loads provided here have not been adjusted with the direct load participation rates (see paper for more details). More details on the dataset can be found in the metaData.Full_Potential.csv file. The acheivable_NUTS2_summary.csv shows the NUTS2 level acheivable direct load control potentials for the average hour in the respective year (years - 2020, 2022,2030,2040, 2050).

Project: Coupled Model Intercomparison Project Phase 6 (CMIP6) datasets - These data have been generated as part of the internationally-coordinated Coupled Model Intercomparison Project Phase 6 (CMIP6; see also GMD Special Issue: http://www.geosci-model-dev.net/special_issue590.html). The simulation data provides a basis for climate research designed to answer fundamental science questions and serves as resource for authors of the Sixth Assessment Report of the Intergovernmental Panel on Climate Change (IPCC-AR6). CMIP6 is a project coordinated by the Working Group on Coupled Modelling (WGCM) as part of the World Climate Research Programme (WCRP). Phase 6 builds on previous phases executed under the leadership of the Program for Climate Model Diagnosis and Intercomparison (PCMDI) and relies on the Earth System Grid Federation (ESGF) and the Centre for Environmental Data Analysis (CEDA) along with numerous related activities for implementation. The original data is hosted and partially replicated on a federated collection of data nodes, and most of the data relied on by the IPCC is being archived for long-term preservation at the IPCC Data Distribution Centre (IPCC DDC) hosted by the German Climate Computing Center (DKRZ). The project includes simulations from about 120 global climate models and around 45 institutions and organizations worldwide. Summary: These data include the subset used by IPCC AR6 WGI authors of the datasets originally published in ESGF for 'CMIP6.CMIP.NUIST.NESM3.amip' with the full Data Reference Syntax following the template 'mip_era.activity_id.institution_id.source_id.experiment_id.member_id.table_id.variable_id.grid_label.version'. The NUIST ESM v3 climate model, released in 2016, includes the following components: atmos: ECHAM v6.3 (T63; 192 x 96 longitude/latitude; 47 levels; top level 1 Pa), land: JSBACH v3.1, ocean: NEMO v3.4 (NEMO v3.4, tripolar primarily 1deg; 384 x 362 longitude/latitude; 46 levels; top grid cell 0-6 m), seaIce: CICE4.1. The model was run by the Nanjing University of Information Science and Technology, Nanjing, 210044, China (NUIST) in native nominal resolutions: atmos: 250 km, land: 2.5 km, ocean: 100 km, seaIce: 100 km.

Project: Coupled Model Intercomparison Project Phase 6 (CMIP6) datasets - These data have been generated as part of the internationally-coordinated Coupled Model Intercomparison Project Phase 6 (CMIP6; see also GMD Special Issue: http://www.geosci-model-dev.net/special_issue590.html). The simulation data provides a basis for climate research designed to answer fundamental science questions and serves as resource for authors of the Sixth Assessment Report of the Intergovernmental Panel on Climate Change (IPCC-AR6). CMIP6 is a project coordinated by the Working Group on Coupled Modelling (WGCM) as part of the World Climate Research Programme (WCRP). Phase 6 builds on previous phases executed under the leadership of the Program for Climate Model Diagnosis and Intercomparison (PCMDI) and relies on the Earth System Grid Federation (ESGF) and the Centre for Environmental Data Analysis (CEDA) along with numerous related activities for implementation. The original data is hosted and partially replicated on a federated collection of data nodes, and most of the data relied on by the IPCC is being archived for long-term preservation at the IPCC Data Distribution Centre (IPCC DDC) hosted by the German Climate Computing Center (DKRZ). The project includes simulations from about 120 global climate models and around 45 institutions and organizations worldwide. Summary: These data include the subset used by IPCC AR6 WGI authors of the datasets originally published in ESGF for 'CMIP6.GMMIP.CAS.FGOALS-f3-L' with the full Data Reference Syntax following the template 'mip_era.activity_id.institution_id.source_id.experiment_id.member_id.table_id.variable_id.grid_label.version'. The FGOALS-f3-L climate model, released in 2017, includes the following components: atmos: FAMIL2.2 (Cubed-sphere, c96; 360 x 180 longitude/latitude; 32 levels; top level 2.16 hPa), land: CLM4.0, ocean: LICOM3.0 (LICOM3.0, tripolar primarily 1deg; 360 x 218 longitude/latitude; 30 levels; top grid cell 0-10 m), seaIce: CICE4.0. The model was run by the Chinese Academy of Sciences, Beijing 100029, China (CAS) in native nominal resolutions: atmos: 100 km, land: 100 km, ocean: 100 km, seaIce: 100 km.

Data reported by companies on the production, import, export, destruction and feedstock use of fluorinated greenhouse gases in the European Union during the years 2007-2019. The primary data is synthesised and aggregated at EU level and used to assess the progress on HFC phase-down made under both EU legislation and the UN framework as part of the Kigali Amendment to the Montreal Protocol. The data also details the amount of F-gases supplied to various industrial applications.

Project: Coupled Model Intercomparison Project Phase 6 (CMIP6) datasets - These data have been generated as part of the internationally-coordinated Coupled Model Intercomparison Project Phase 6 (CMIP6; see also GMD Special Issue: http://www.geosci-model-dev.net/special_issue590.html). The simulation data provides a basis for climate research designed to answer fundamental science questions and serves as resource for authors of the Sixth Assessment Report of the Intergovernmental Panel on Climate Change (IPCC-AR6). CMIP6 is a project coordinated by the Working Group on Coupled Modelling (WGCM) as part of the World Climate Research Programme (WCRP). Phase 6 builds on previous phases executed under the leadership of the Program for Climate Model Diagnosis and Intercomparison (PCMDI) and relies on the Earth System Grid Federation (ESGF) and the Centre for Environmental Data Analysis (CEDA) along with numerous related activities for implementation. The original data is hosted and partially replicated on a federated collection of data nodes, and most of the data relied on by the IPCC is being archived for long-term preservation at the IPCC Data Distribution Centre (IPCC DDC) hosted by the German Climate Computing Center (DKRZ). The project includes simulations from about 120 global climate models and around 45 institutions and organizations worldwide. Summary: These data include the subset used by IPCC AR6 WGI authors of the datasets originally published in ESGF for 'CMIP6.CMIP.CMCC.CMCC-CM2-SR5.historical' with the full Data Reference Syntax following the template 'mip_era.activity_id.institution_id.source_id.experiment_id.member_id.table_id.variable_id.grid_label.version'. The CMCC-CM2-SR5 climate model, released in 2016, includes the following components: aerosol: MAM3, atmos: CAM5.3 (1deg; 288 x 192 longitude/latitude; 30 levels; top at ~2 hPa), land: CLM4.5 (BGC mode), ocean: NEMO3.6 (ORCA1 tripolar primarly 1 deg lat/lon with meridional refinement down to 1/3 degree in the tropics; 362 x 292 longitude/latitude; 50 vertical levels; top grid cell 0-1 m), seaIce: CICE4.0. The model was run by the Fondazione Centro Euro-Mediterraneo sui Cambiamenti Climatici, Lecce 73100, Italy (CMCC) in native nominal resolutions: aerosol: 100 km, atmos: 100 km, land: 100 km, ocean: 100 km, seaIce: 100 km.

Abstract Energy storage systems (ESS) are widely used in active distribution networks (ADN) to smoothen the drastic fluctuation of renewable energy sources (RES). In order to enhance the scalability and flexibility of ESS, a virtual energy storage system (VESS), which is composed of battery energy storage system (BESS), RES as well as flexible loads (FL), is developed in this paper to realize the functionalities of ESS in more cost-effective way in ADN. Aiming at achieving voltage regulation, dynamic pricing strategies based on system voltage condition are designed for VESS. A distributed real-time power management model containing dynamic pricing strategies is proposed to accomplish the voltage regulation and economic power sharing in VESS. Moreover, a set of distributed algorithms, over time-varying unbalanced directed networks, are designed for dynamic pricing strategies and optimal power management model. Furthermore, the convergence property, optimality and system voltage stability are explained by detailed mathematical analysis. Three various case studies which were ran on a real time digital simulator (OPAL-RT OP5600) were designed to validate the effectiveness of the strategy. Finally, simulation results show that the economic power dispatch and voltage regulation are achieved among VESS simultaneously, even in the presence of time-varying directed and unbalanced communication networks.

Abstract To achieve the EU climate and energy objectives, a transition towards a future sustainable energy system is needed. The integration of the huge potential for industrial waste heat recovery into smart energy system represents a main opportunity to accomplish these goals. To successfully implement this strategy, all the several stakeholders' conflicting objectives should be considered. In this paper an evolutionary multi-objective optimization model is developed to perform a sustainability evaluation of an energy system involving an industrial facility as the waste heat source and the neighbourhood as district heating network end users. An Italian case study of heat recovery from a steel casting facility shows how the model allows to properly select the district heating network set of users to fully exploit the available waste energy. Design directions such as the thermal energy storage capacity can be also provided. Moreover, the model enables the analysis of the trade-off between the stakeholders’ different perspectives, allowing to identify possible win-win solutions for both the industrial sector and the citizenship.