• Energy Research
• Restricted close
• US close
• EU close
• CN close
• CNR ExploRA close

Diesel engine exhausts from a common rail 3.0 L F1C diesel engine were analyzed at two different load conditions of the WLTC testing cycle downstream of both the diesel particulate filter (DPF) and selective catalytic reactor (SCR) to verify their effect on the characteristics of carbon particulate matter. An array of chemical, physical and spectroscopic techniques (gas chromatography coupled with mass spectrometry (GC-MS), mobility analyzer, UV-Visible absorption and fluorescence spectroscopy) was applied for characterizing polycyclic aromatic hydrocarbons (PAH), heavy aromatic compounds and soot, constituting the particulate matter (PM) sampled from the exhaust. The engine was operated in half load (HL) (188 Nm, representing the more common condition for engine in urban traffic) and full load (FL) (452 Nm, representing the best performance of the engine operation) conditions, at the same engine speed (2000 rpm). Soot formation was enhanced in HL condition, with respect to FL, but, just because of the much lower soot amount, the after-treatment systems in this last condition resulted to be less efficient in the soot abatement. Indeed, the abatement through DPF was about 40% lower in the FL condition with respect to HL condition, and any significant further concentration decrease was found after SCR, in both conditions. By contrast, PAH concentration after DPF abatement was found to be higher in the HL with respect to FL condition. A further PAH concentration decrease of about 30% was found after the SCR in the HL condition whereas in FL the reduction was only about 5-6%. Also the heavy aromatic compounds having molecular weight above the GC-MS detection limit (300 u), were mitigated by SCR. Therefore, SCR did not cause a further soot reduction, whereas it was effective in largely reducing PAH and heavy aromatics emissions, especially in the lower temperature condition featuring the half-load condition, when combustion efficiency is worse. Moreover, SCR system reduced the emission of small particles probably due to an enhanced agglomeration of particles, with beneficial effect on the harmfulness to human health.

Originally developed and validated at the Cabauw (Netherlands) topographically flat onshore location, the alpha-I wind resource extrapolating method was tested at the FINO3 offshore site in the North Sea (Germany). The aim was to prove its validity also when applied over a substantially different environment in terms of surface characteristics and stability conditions. Data from local mast at 30, 80, and 100 m were used, with extrapolations to 80-m and 100-m turbine hub heights accomplished based on 30-m turbulence intensity observations. Trained over a 2-year period (2011-2012), the method was validated on year 2013. Similarly to the onshore application, the method was reliable in extrapolating wind speed to both 80 m and 100 m, with bias within 5%, NRMSE = 0.20 and r = 0.94. Conversely, scores were largely better than at the onshore site in predicting the annual energy yield, biased by 0.41-1.02% at 80 m, and 1.12-1.36% at 100 m. The method proved to be highly sensitive to the stability classification, as not considering this option increased its biases to 4.51-5.93% at 80 m, and 7.46-8.23% at 100 m. Method's reliability might suitably help reduce the number of masts installed throughout a large offshore area.

In this paper some preliminary experimental results on a Zebra battery based propulsion system for urban bus applications are presented. The tests were carried out using a laboratory 1:1 scale test bench, composed by a 65 kW electric drive, specifically designed for urban bus applications, supplied by two 20 kWh Zebra batteries connected in parallel. The electric power train was tested on a laboratory bench, connected through a fixed ratio gear box to a 100 kW regenerative electric brake provided with speed and torque controls, in order to evaluate the propulsion system performance in steady state operative conditions. The obtained preliminary experimental results were utilized to implement a Matlab-Simulink model of urban bus, which might be powered by the same electric propulsion system studied. Thanks to this model it was possible to evaluate the dynamic behavior of the urban bus, working on standard driving cycles, taking into account the resistant forces represented by proper vehicle/road/aerodynamic parameters. An evaluation of the expected real vehicle driving range was also estimated in different road conditions.

The most widely used process for hydrogen production is steam methane reforming. It can be carried out using a membrane reactor in which simultaneous hydrogen production and purification occur. Mathematical modeling of these reactors plays a key role in the selection of the design and operating parameters that yield high performance for the reactor. This review study discusses, synthesizes, and compares different mathematical modeling studies on the packed bed membrane reactors for hydrogen production from methane found in the literature. Different approaches used in these modeling studies for the hydrogen permeation steps, reaction kinetic expressions, phases involved (pseudo-homogeneous and heterogeneous), and spatial dimensions (one, two, and three dimensional) are given.

Intention of this work is to investigate the opportunity and feasibility of energy efficient networking in Home and Building automation protocols. Wired HBAS have traditionally devoted a relatively little attention to this point, especially if compared to wireless networks. This paper will try to address the issue by evaluating the introduction of power state switching in a real scenario and proposing the concept of functional and spatial adjacency among packets.

Decentralized detection in a network of wireless sensor nodes involves the fusion of information about a phenomenon of interest (PoI) from geographically dispersed nodes. In this paper, we investigate the problem of binary decentralized detection in a dense and randomly deployed wireless sensor network (WSN), whereby the communication channels between the nodes and the fusion center are bandwidth-constrained. We consider a scenario in which sensor observations, conditioned on the alternate hypothesis, are independent but not identically distributed across the sensor nodes.We compare two different fusion architectures, namely, the parallel fusion architecture (PFA) and the cooperative fusion architecture (CFA), for such bandwidthconstrained WSNs, where each sensor node is restricted to send a 1-bit information to the fusion center. For each architecture, we derive expression for the probability of decision error at the fusion center. We propose a consensus flooding protocol for CFA and analyze its average energy consumption. We analyze the effects of PoI intensity, realistic link models, consensus flooding protocol, and network connectivity on the system reliability and average energy consumption for both fusion architectures. We demonstrate that a trade-off exists among spatial diversity gain, average energy consumption, delivery ratio of the consensus flooding protocol, network connectivity, node density, and PoI intensity in CFA. We then provide insight into the design of cooperative WSNs.

Wood biomass is turned into industrial fuel through chipping. The efficiency of chipping depends on many factors, including chipper knife wear. Chipper knife wear was determined through a long-term follow-up study, conducted at a waste wood recycling yard. Knife wear determined a sharp drop of productivity (>20%) and a severe decay in product quality. Dry sharpening with a grinder mitigated this effect, but it could not replace proper wet sharpening. Increasing the frequency of wet sharpening sessions determined a moderate increase of knife depreciation cost, but it could drastically enhance machine performance and reduce biomass processing cost. Since benefits largely exceed costs, increasing the frequency of wet sharpening sessions may be an effective measure for reducing overall chipping cost. If the main goal of a chipper operator is to increase productivity and/or decrease fuel consumption, then managing knife wear should be a primary target. (C) 2014 Elsevier Ltd. All rights reserved.

Alternative fuels and energy vectors are becoming increasingly important in terms of technical, geopolitical, economic, and environmental aspects. In particular, gaseous fuels and vectors, such as fossil or synthetic natural gas (NG) blended with hydrogen, commonly help provide optimal strategies to reduce global and toxic emissions of internal combustion engines, owing to their adaptability, anti-knock capacity, lower toxicity of pollutants, reduced CO2 emissions, and costeffectiveness. However, diesel engines still represent the reference category among internal combustion engines in terms of maximum thermodynamic efficiency. The possibility offered by dual-fuel (DF) systems to combine the efficiency and performance of diesel engines with the environmental advantages of gaseous fuels has been the subject of extensive investigations. However, the simple replacement of diesel fuel with gaseous fuel does not allow for optimising the engine performance, owing to the high percentage of unburned gaseous fuel, which compromises the potential reduction of CO2; therefore, more complex combustion strategies should be realised. In this study, with the aim of improving the DF combustion process, an experimental investigation was performed to analyse low-temperature combustion (LTC), using NG and two enriched hydrogen-compressed NG blends as primary fuels. The LTC mode was activated by means of a very early advanced pilot injection and carried out in two close steps. The double pilot injection was used to control the energy release rate in the first combustion stage, thereby minimizing the increase of the rate of pressure and allowing the extension of the operation range under LTC. The experimental activity was also focused on analysing the particle emissions, as it is well known that these emissions, together with those of nitrogen oxide, constitute the main pollutants resulting from diesel fuel combustion. The results demonstrated the potential to reduce the unburned fuel, NOx, and particle emissions simultaneously, while maintaining equivalent CO2 emissions to a diesel-only engine. Both the timing and pressure of the pilot injection proved to be critical parameters for optimising the emissions and performance