• Energy Research
• 7. Clean energy close
• 12. Responsible consumption close
• 3. Good health close
• CO close

The present paper develops a methodology to choose the best connection scheme for traction substations of a Massive Electrical Railway System (MERS) and distribution substations in urban areas using graph theory and economical optimization.

Flue gas desulfurization (FGD) and selective catalytic reduction (SCR) technologies have been widely used to control the emissions of sulphur dioxide (SO2) and nitrogen oxides (NOX) from coal-fired power plants (CFPPs). Field measurements of emission characteristics of four conventional CFPPs indicated a significant increase in particulate ionic species, increasing PM2.5 emission with FGD and SCR installations. The mean concentrations of PM2.5 from all CFPPs tested were 3.79 ± 1.37 mg/m3 and 5.02 ± 1.73 mg/m3 at the FGD inlet and outlet, respectively, and the corresponding contributions of ionic species were 19.1 ± 7.7% and 38.2 ± 7.8%, respectively. The FGD was found to enhance the conversion of NH3 slip from the SCR to NH4+ in the PM2.5, together with the conversion of SO2 to SO42-, and increased the primary NH4+ and SO42- aerosol emissions by approximately 18.9 and 4.2 times, respectively. This adverse effect should be considered when updating the emission inventory of CFPPs and should draw the attention of policy-makers for future air pollution control.

Abstract Small-scale hydroelectric plants, primarily run-of-the-river designs, are regularly subjected to hard particle wear and cavitation erosion due to the wide range of operating points. Depending on the severity of the operating conditions and erosion damage experienced by the machine throughout its service life, the operating companies of these facilities will be impacted. The impact will be technical, operational, logistical, and economic. A small-scale generation plant located in Amaime River in Colombia, is one such case, where severe wear occurs in the turbine components, with a consequent reduction of efficiency. In this study, the analysis of the erosion damage has been expanded and supplemented by computational fluid dynamics (CFD). From this approach, correlations between the wear rate and power output were obtained. Likewise and in conjunction with the computer estimates, a methodology to analyse the costs associated with wear based on historical data of operation was developed, creating a strategy of operation based on a stopping criterion that depends primarily on sediment concentration, turbinated flow, and wear level. The methodology optimizes the use of generators, which takes into consideration the revenue generation and the costs associated with operation and maintenance of pieces under conditions of intrinsic erosion wear in the facility.

SUMMARYThis article discusses how decentralisation policies are enacted in the planning and implementation of natural resource management interventions in rural Ethiopia. A key element of decentralisation policy is the emphasis on greater participation by local communities. Drawing on qualitative research conducted with government staff and farmers, this paper illustrates how different actors perceive and implement national policy and how these actions affect the longer‐term sustainability of land management interventions. Copyright © 2014 John Wiley & Sons, Ltd.

Transformative Innovation Policy (TIP) is a new paradigm in science, technology, and innovation policy that seeks to produce a transition to sustainable development. In this paradigm, universities are crucial actors in the dynamics of science, technology, and innovation, but their role in the implementation of TIP should be defined. The objective of this article is to contribute to the understanding of the ideal role of Latin American universities in the implementation of TIP. Therefore—to describe and analyze the concepts of university and TIP in Latin America—this case study examines the co-creation of a public policy of science, technology, and innovation by Higher Education Institutions (HEIs) in that region. This article underscores the vital role of universities in promoting transformative innovation that fosters social inclusion and sustainability. To achieve this goal, structural policy changes should be implemented, and different stakeholders (including researchers, students, and civil society) should be actively engaged. This paper also highlights the importance of addressing socio-economic, cultural, political, cognitive, and environmental issues faced by marginalized communities. By embracing the principles of transitions theory and prioritizing transformative innovation, universities can make significant contributions towards achieving Sustainable Development Goals (SDGs).

The black liquor is a byproduct of the kraft pulping process that contains more than half of the exergy content in the total woody biomass fed to the digester, representing a key supply of renewable energy to the pulping process. In this work, the conventional scenario of the black liquor use (i.e., concentration and combustion) is compared with the black liquor upgrading (via) gasification process for ammonia production in terms of economics, exergy efficiency and environmental impact. The combined energy integration and exergy analysis is used to identify the potential improvements that may remain hidden to the energy analysis alone, namely, the determination and mitigation of the process irreversibility. As a result, the exergy efficiencies of the conventional and the integrated cases average 40% and 42%, respectively, whereas the overall emission balance varies from 1.97 to −0.69 tCO2/tPulp, respectively. The negative CO2 emissions indicate the environmental benefits of the proposed integrated process compared to the conventional kraft pulp mill.

espanolSe presentan los resultados de un estudio sobre la significancia y la optimizacion de algunas variables (granulometria, velocidad de aire, contenido de biomasa y disposicion del reactor) en el poder calorifico del gas de sintesis obtenido de la gasificacion de biomasa (carbon vegetal y cuesco de palma africana). Mediante un diseno de experimento se evaluaron las cuatro variables que oscilaban entre 8-13mm para la granulometria, 0.8-1.4m/s para la velocidad del aire, 0-100 para el contenido de biomasa y ascendente-descendente para la disposicion del reactor. Se encontro que los factores correspondientes a la granulometria y el contenido de biomasa resultan ser los mas significativos en el poder calorifico del gas. Un poder calorifico maximo de 3.84MJ/Nm3 se obtuvo con la disposicion descendente del reactor, alimentacion de carbon vegetal con granulometria de 13mm y suministro maximo de flujo de aire. La verificacion del punto optimo de operacion mostro que tales condiciones de operacion favorecian la produccion de un gas con un alto poder calorifico. EnglishThe results of study on the significance and the optimization of some variables (particle size, air flow, biomass content and reactor disposition) in the calorific value of the synthesis gas obtained by gasification process of biomass (vegetal coal and biomass African palm) is presented. The four variables ranged from 8-13mm for the particle size, 0.8-1.4m/s for air flow, 0-100 for biomass content and updraft-downdraft disposition for the type of reactor were evaluated by an experimental design. It was found that the particle size and biomass content are the most significant factors to maximize the output calorific value of syngas. A maximum calorific value of 3.84MJ/Nm3 was obtained using the downdraft reactor with 13mm particle size and maximum air flow supply. The verification of the optimum operating point under these conditions showed that such operating conditions favored the production of a gas with high calorific value.

Currently Smart Grids are considered as an optimum model for energy supply. It improves the efficiency, reliability and availability of the electricity supply. It uses structures to achieve compliance with interoperation that are used across the entire network. To achieve this, special devices are distributed through the entire grid. A RMU (Ring Main Unit) is a device that makes measurements of electrical variables of the grid and sends wirelessly information to a central station MTU (Master Terminal Unit). The RMU has the capacity to detect failures and perform control by disconnecting the grid. In this article, it is shown the design and manufacture of a scale RMU.

This work is the result to the study a different systems of exhaust pipes. The manufacturers of motorbike use a system with several volumes to reduce noise and use a catalyst to reduce emissions. In contrast, the manufacturers of exhaust system decided made a system using a perforated pipe and a rock wool to noise reducing. This system changes the pressure drop and temperature of exhaust gases and, therefore, request a different composition of catalyst.In this communication, it is shown the tests released in a test bench according with the cycle WLTC and the limits are the defined for EURO3. Where, we have changed the type of catalyst, the diameter of the end pipe and the calibration of electronic control unit of engine in order to measure following the test of homologation.The results of the different experiments indicate is very important the pressure drop in the replace exhaust system must be similar to the original system. The composition of the catalyst and the operating temperature are critical to reduce the emissions and the calibration of engine is the main influence. Keywords: Exhaust systems, Catalyst, Regulatory emissions, WLTC