• Energy Research
• Open Access close
• Closed Access close
• Open Source close
• Embargo close
• US close
• DE close
• BE close

Abstract In this paper, the prevention of negative technogenic impact on the environment of oil sludge by using it as a secondary resource is considered. Oil sludge from various objects of oil fields in Kazakhstan (Mangystau region) has been studied. The possibilities of using oil (after its separation from oil sludge by bioremidiation) as a partial substitute for bitumen base in the production of modified bitumen are considered. The main physical and mechanical characteristics of modified bitumen are determined. The results confirm that the modified bitumen prepared with oil sludge and oil separated by bioremiation method meets the requirements for polymer-bitumen binder to Kazakhstan standards and is suitable for the production of modified bitumen in its physico-chemical characteristics.

The feasibility of rehabilitating an existing power house at the Enloe Dam in Washington was evaluated with consideration of expected power production, social and environmental impacts, regulatory aspects, technical requirements, financing, costs, and market potential. This assessment showed that rebuilding the existing powerhouse and appurtenant facilities is technically feasible. Rebuilding the existing turbines and generators proved to be the most desirable of three alternatives considered. The following four factors lead to this conclusion: rebuilding the old equipment is less costly than installing new turbines and generators; no major structural changes to the powerhouse would be required; rebuilding the turbines with increased flow capacity made the rebuilding alternative competitive with new equipment from an energy production standpoint; and rebuilding is compatible with the Enloe site's recent addition to the National Register of Historic Places.

Abstract Wellbore pressure gradient in gas wells is significant in designing deliquification technologies and optimizing production. At present, no model has yet to be established specifically for gas wells at a wide gas flowrate range. When calculating pressure gradient in a specific gas field, engineers must evaluate these widely used models and get the best performance model at a certain range. To establish a more comprehensive model in horizontal gas wells, an experimental study was conducted to investigate the flow behavior of liquid-gas two-phase flow at different gas and liquid velocities and inclined angles in a 50 mm visual pipe. The evaluation of these widely used models against the experimental data shows that no model can predict liquid holdup at different gas velocity ranges, and huge deviations due to several reasons can be observed. After conducting a comprehensive analysis, a new liquid holdup correlation was proposed based on the Mukherjee–Brill model by correlating from the experimental results, which have parametric ranges closer to the production of gas wells. This new model adopts a new dimensionless gas velocity number to characterize flow similarities and better scale up pressure from the experiment to the gas wells. By validating against experimental data and field data, the results indicate that the new two-phase flow model has stable performance and can accurately predict pressure gradients at different ranges of pressure and gas/liquid velocities.

The information and data contained in this Appendix was extracted from numerous sources. The principle sources used for technical data were Bonneville Power Administration's 1990 Resource Program along with its technical appendix, and Chapter 8 of the Draft 1991 Northwest Conservation and Electric Power Plan. All cost data is reported 1988 dollars unless otherwise noted. This information was supplemented by other data developed by Puget Sound utilities who participated on the Local Generation Team. Identifying generating resources available to the Puget Sound area involved a five step process: (1) listing all possible resources that might contribute power to the Puget Sound area, (2) characterizing the technology/resource status, cost and operating characteristics of these resources, (3) identifying exclusion criteria based on the needs of the overall Puget Sound Electric Reliability Plan study, (4) applying these criteria to the list of resources, and (5) summarizing of the costs and characteristics of the final list of resources. 15 refs., 20 tabs.

Mode of access: Internet.

Abstract Heat pipes and two-phase thermosyphons are highly efficient heat transfer devices utilizing continuous evaporation and condensation of working fluid for two-phase heat transport in closed systems. Because of the nearly isothermal and fully passive phase-change heat transfer mechanism, heat pipes and thermosyphons have found many applications in nuclear engineering, space technologies, and other energy systems. High-temperature heat pipes are used in nuclear microreactors to remove fission power from the primary system and are coupled with power conversion systems or process heat applications. Modeling of the two-phase flow phenomena inside a heat pipe is essential to its design and safety analysis. In this study, a comprehensive one-dimensional two-phase three-field flow model has been developed for the analysis of heat pipes in normal operation conditions and transients. The conservation or field equations of mass, momentum, and energy were developed for the liquid film, vapor, and droplet. In addition, constitutive models or correlations were reviewed thoroughly and provided for the closure of the three-field equations. Specific constitutive equations regarding interfacial mass and heat transfer at two interfaces, namely film-gas interface and gas-droplet interface, were reviewed for droplet entrainment and deposition rates as well as film and droplet evaporation rates. Additionally, mechanistic correlations of annular flow film thickness were recommended for the modeling of the thermosyphons without a wick as a critical constitutive correlation. Furthermore, experimental data needs from new experiments using a prototype working fluid or surrogate fluids for the model validation of high-temperature heat pipes in microreactors were recommended for future research.

Accurate predictions of fuel spray behavior and mixture formation in simulations of direct-injection spark-ignition (DISI) engines are fundamental to ensure proper description of all subsequent processes including ignition, combustion, and emissions. In this work, the spray evolution in a single-cylinder optical DISI engine was studied experimentally and numerically with the goal of enabling predictive computational fluid dynamics (CFD) modeling of in-cylinder sprays. The authors explored a wide range of operating conditions characterized by several fuel injection temperatures and engine speeds, using a well-characterized nine-component gasoline surrogate known as PACE-20. The effect of flash boiling and intake crossflow on the spray is discussed, with a focus on evaluating the ability of the spray models to capture highly transient spray behavior. In the experiments, the fuel temperature was varied between 20°C and 80°C, allowing for non-flash- to flash-boiling transition to emerge with enhanced flashing intensity at the highest temperatures. Spray collapse resulted in vapor-rich regions, owing to the locally lower inertia of the fluid. Varying the engine speed from 650 to 1950 rpm promoted increasingly more turbulent in-cylinder crossflow which interacted with the spray during the injection event and resulted in enhanced spray dispersion. The CFD model was able to capture the spray morphology transition at different fuel temperatures and engine speeds adequately. It is shown that the spray breakup model could capture the transitional spray behavior induced by flash boiling atomization and intake flow via proper initialization of the spray cone angle and calibration of the spray models’ constants.

Abstract Fractures along interfaces between host rock and wellbore cement have long been identified as potential CO2 leakage pathways from subsurface CO2 storage sites. As a consequence, cement alteration due to exposure to CO2 has been studied extensively to assess wellbore integrity. Previous studies have focused on the changes to either chemical or mechanical properties of cement upon exposure to CO2-enriched brine, but not on the effects of loading conditions. This paper aims to correct this deficit by considering the combined effects of the fracture pathway and changing effective stress on chemical and mechanical degradation at conditions relevant to geologic carbon storage. Flow-through experiments on fractured cores composed of cement and tight sandstone caprock halves were conducted to study the alteration of cement due to exposure to CO2-enriched brine at 3, 7, 9, and 12 MPa effective stress. We characterized relevant reactions via solution chemistry; fracture permeability via changes to differential pressure; mechanical changes via micro-hardness testing, and pore structure changes via x-ray tomography. This study showed that the nature and the rates of the chemical reactions between cement and CO2 were not affected by the effective stress. The differences in the permeability responses of the fractures were attributed to interactions among the geometry of the flow path, the porosity increase of the reacted cement, and the mechanical deformation of reacted asperities. The suite of observed chemical reactions contributed to change in cement mechanical properties. Compared to the unreacted cement, the average hardness of the amorphous silica and depleted layers was decreased while the hardness of the calcite layer was increased. Tomographic imaging showed that preferential flow paths formed in some of the core-flood experiments, which had a significant impact on the permeability response of the fractured samples. We interpreted the observed permeability responses in terms of competition between dissolution of cement phases (leading to enhanced permeability) and mechanical deformation of reacted regions (leading to reduced permeability).