• Energy Research
• Closed Access close
• Open Source close
• 7. Clean energy close
• DE close
• CA close
• ES close

Abstract AP1000® Generation III+ reactor bases its safety concept on passive systems, differently from the previous Generation II reactors. This fact has led the approximations and methodologies previously used for modeling active safety systems to be reviewed and adapted to simulate the physics of passive systems. Diverse studies about the AP1000 containment have demonstrated the difficulty to correctly model the occurring phenomenology. In this paper, an integral AP1000 3D containment GOTHIC model is presented, including the Passive Containment Cooling System (PCCS). The model includes the compartments inside and outside the metallic containment liner that influence the thermal–hydraulic behavior. The model is tested against a Large Break Loss of Coolant Accident (LBLOCA) to assess its thermal–hydraulic performance, assuming a PCS tank malfunction, what is a conservative hypothesis. The pressure and temperature evolution predicted by the 3D containment model is analyzed and compared with a single node Lumped Parameters model, allowing to evaluate some preliminary benefits of 3D modeling for containment safety analysis. The 3D containment model allows to predict the thermal evolution in each containment compartment capturing the heterogeneity of this phenomenon, with higher resolution than the lumped parameters models traditionally used in this kind of analyses. It allows to observe the thermohydraulic conditions locally at any time during the transient.

Abstract Thermal performance of three naturally ventilated public buildings in which the wind tower is an important architectural freature is studied. One of the three builidings as well as it's wind tower is instrumented for temperature, relative humidity and airflow velocity measurements, and the other two are instrumented for temperature measurement. The results have led to a discussion concerning the degree of wind tower effectiveness in achieving thermal comfort.

Successive international commitments relating to energy and climatic change (embodied in the Kyoto Protocol) and the need to rationalise the sources of generated energy, have meant that renewable energies have started to gain a great deal of importance within the worldwide energy network. In the case of Wind Energy, and in terms of production, Spain is the second most important country at European level and the third most important country at global level. Spain holds these positions as a result of the establishment of a stable regulatory framework, better understanding of the resource and improved technology that have afforded considerable cost reduction in terms of initial investment, maintenance and exploitation. This article focuses on these circumstances in view of their relevance at international level, which is due to the highly feasible possibility of exporting Spain's experiences to other countries with guarantees of success.

Abstract Hybrid energy storage is a multi-modal approach to store and supply different forms of energy (electricity, heat, cold) simultaneously. This is an important sector coupling approach and enables large scale flexibility for a deep decarbonization of energy systems. Two different proposed energy storages – power-to-heat-to-X energy storage (PHXES) and pumped thermal energy storage (PTES) – are investigated in detail in this work towards their potential towards a hybrid deployment. The techno-economic analysis includes thermodynamic flowsheet simulations and unified cost estimations based on the used equipment. It is shown that the main input data set (e.g. working fluid selection, turbomachinery efficiency, pinch temperatures) has a strong influence on storage roundtrip efficiency in the thermodynamic simulations, but also on storage costs. Cost decrease and performance increase can be conflicting development targets, and it is not clear if future energy systems rather require technologies with the highest storage efficiencies or if low cost is an important prerequisite. PHXES and three variants of PTES are implemented into a simplified energy system model of the city of Hamburg that comprises the electric load and heat demand of the district heating system. Two scenarios (fossil benchmark and 80% decarbonization) are used to select the technologies and their capacities that allow the most cost-effective energy supply solution by a linear-programming optimization procedure. Large scale renewable power generation and hybrid energy storage play the major roles in the decarbonization scenario. PHXES with a storage capacity of 69 GWh, hot water storage (3.6 GWh) and a battery system (430 MWh) are part of the cost-optimal solution. A cost sensitivity analysis shows that a total cost reduction of 60–80% is required for PTES to become competitive in this model scenario.

Previous work carried out for the last eight years resulted in the proposal of a complete system of dimensionless groups in order to represent the performance of different kinematic Stirling engine configurations. When looking for experimental support for the proposed model, some differences between the performances of several prototypes were observed. In this paper an equation is introduced to be applied to all known kinematic engines and to their whole range of performance. The coefficients appearing in this equation can be computed from temperature and geometrical dimensionless ratios and from experimental measurements at the maximum indicated power operating point. The meaning of those coefficients is interpreted and their usefulness to provide an engine performance overview is shown. The quasi-static simulation and the characteristic Mach number at the maximum indicated power operating point appear to be interesting criteria in order to evaluate the performance of prototypes.

Bioplastics are alternatives of conventional petroleum-based plastics. Bioplastics are polymers processed from renewable sources and are biodegradable. This study aims at conducting an environmental impact assessment of the bioprocessing of agricultural wastes into bioplastics compared to petro-plastics using an LCA approach. Bioplastics were produced from potato peels in laboratory. In a biochemical reaction under heating, starch was extracted from peels and glycerin, vinegar and water were added with a range of different ratios, which resulted in producing different samples of bio-based plastics. Nevertheless, the environmental impact of the bioplastics production process was evaluated and compared to petro-plastics. A life cycle analysis of bioplastics produced in laboratory and petro-plastics was conducted. The results are presented in the form of global warming potential, and other environmental impacts including acidification potential, eutrophication potential, freshwater ecotoxicity potential, human toxicity potential, and ozone layer depletion of producing bioplastics are compared to petro-plastics. The results show that the greenhouse gases (GHG) emissions, through the different experiments to produce bioplastics, range between 0.354 and 0.623 kg CO2 eq. per kg bioplastic compared to 2.37 kg CO2 eq. per kg polypropylene as a petro-plastic. The results also showed that there are no significant potential effects for the bioplastics produced from potato peels on different environmental impacts in comparison with poly-β-hydroxybutyric acid and polypropylene. Thus, the bioplastics produced from agricultural wastes can be manufactured in industrial scale to reduce the dependence on petroleum-based plastics. This in turn will mitigate GHG emissions and reduce the negative environmental impacts on climate change.

Abstract Thermal energy storage with phase change materials (PCM) provides high storage capacities in small temperature intervals. For the design of storage systems, the enthalpy curve of the used PCM has to be known with high precision. The T-History method has evolved to a widely used method for the measurement of the enthalpy as a function of temperature of PCM because of its simplicity and the advantage to be able to investigate larger sample volumes than typically used for differential scanning calorimeters. In order to ensure isothermal specimen during the measurement a thermal insulation is often mounted around the sample holder, but this insulation material is not considered in the evaluation model. In this work a new evaluation model for insulated T-History setups is developed by an analytical heat balance. This model is validated by numerical simulations of insulated T-History measurements and experimentally. By the use of the new model for the evaluation of the enthalpy a significant increase of accuracy can be achieved.

This paper presents an experimental study of indoor thermal environment near a full-scale glass facade with different types of shading devices under varying climatic conditions in winter. Interior glazing and shading temperature, operative temperature and radiant temperature asymmetry were measured for facade sections with roller shades and venetian blinds at different positions. Interior glass surface temperatures can be high during sunny days with low outdoor temperature. Shading systems significantly improved operative temperature and radiant temperature asymmetry during cold sunny days, depending on their properties and tilt angle. During cloudy days the impact was smaller, however the shading layers could still decrease the amount of heat loss through the facade. A transient building thermal model, which also calculates indoor environmental indices under the presence of solar radiation, was developed and compared with the experimental measurements. Part II of this paper uses this validated model with a transient, two-node thermal comfort model (including transmitted solar radiation) for assessment of indoor environmental conditions with different building envelope and shading properties, facade location and orientation.

Energy management is an enabling technique to guarantee the reliability and economy of hybrid electric systems. This paper proposes a novel machine learning-based energy management strategy for a hybrid electric bus (HEB), with an emphasized consciousness of both thermal safety and degradation of the onboard lithium-ion battery (LIB) system. Firstly, the deep deterministic policy gradient (DDPG) algorithm is combined with an expert-assistance system, for the first time, to enhance the “cold start” performance and optimize the power allocation of HEB. Secondly, in the framework of the proposed algorithm, the penalties to over-temperature and LIB degradation are embedded to improve the management quality in terms of the thermal safety enforcement and overall driving cost reduction. The proposed strategy is tested under different road missions to validate its superiority over state-of-the-art techniques in terms of training efficiency and optimization performance.