• Energy Research
• 2021-2025close
• other engineering and technologies close
• IT close
• DE close
• ES close

Particle receivers are gaining importance in the field of Concentrating Solar Power (CSP) due to the high temperature that particles can achieve without degradation. Several researchers are studying the potential of this technology by means of system analyses, which need simple and light models of the system. This study presents two simple models for the particle receiver. The simplest model is a correlation obtained by fitting the results calculated with a more complex receiver model simulated in CFD. The other model is a 1D model, which is benchmarked against the same CFD results. Although both models achieve high coefficient of determination, R2, when compared to CFD results, the 1D model seems to provide more accurate results (especially during sunsets and sunrises). Both models are integrated into a tecno-economic model developed in previous work. The LCOE obtained with the 1D model is between 7% and 10% greater than the one obtained with the correlation.

This study focuses on formulating the most sustainable concrete by incorporating recycled concrete aggregates and other products retrieved from construction and demolition (C&D) activities. Both recycled coarse aggregates (RCA) and recycled fine aggregates (RFA) are firstly used to fully replace the natural coarse and fine aggregates in the concrete mix design. Later, the cement rich ultrafine particles, recycled glass powder and mineral fibres recovered from construction and demolition wastes (CDW) are further incorporated at a smaller rate either as cement substituent or as supplementary additives. Remarkable properties are noticed when the RCA (4–12 mm) and RFA (0.25–4 mm) are fully used to replace the natural aggregates in a new concrete mix. The addition of recycled cement rich ultrafines (RCU), Recycled glass ultrafines (RGU) and recycled mineral fibres (RMF) into recycled concrete improves the modulus of elasticity. The final concrete, which comprises more than 75% (wt.) of recycled components/materials, is believed to be the most sustainable and green concrete mix. Mechanical properties and durability of this concrete have been studied and found to be within acceptable limits, indicating the potential of recycled aggregates and other CDW components in shaping sustainable and circular construction practices. The authors wish to acknowledge the financial support from EU Horizon 2020 Project VEEP ‘‘Cost-Effective Recycling of C&DW in High Added Value Energy Efficient Prefabricated Concrete Compo-nents for Massive Retrofitting of our Built Environment” (No.723582).

Abstract AP1000® Generation III+ reactor bases its safety concept on passive systems, differently from the previous Generation II reactors. This fact has led the approximations and methodologies previously used for modeling active safety systems to be reviewed and adapted to simulate the physics of passive systems. Diverse studies about the AP1000 containment have demonstrated the difficulty to correctly model the occurring phenomenology. In this paper, an integral AP1000 3D containment GOTHIC model is presented, including the Passive Containment Cooling System (PCCS). The model includes the compartments inside and outside the metallic containment liner that influence the thermal–hydraulic behavior. The model is tested against a Large Break Loss of Coolant Accident (LBLOCA) to assess its thermal–hydraulic performance, assuming a PCS tank malfunction, what is a conservative hypothesis. The pressure and temperature evolution predicted by the 3D containment model is analyzed and compared with a single node Lumped Parameters model, allowing to evaluate some preliminary benefits of 3D modeling for containment safety analysis. The 3D containment model allows to predict the thermal evolution in each containment compartment capturing the heterogeneity of this phenomenon, with higher resolution than the lumped parameters models traditionally used in this kind of analyses. It allows to observe the thermohydraulic conditions locally at any time during the transient.

UV/visible light is a promising radiation source for biomass pretreatment, but very little knowledge is available on the effect of UV on the thermal behavior of lignocellulose in comparison with more classical, physical pretreatment methods. In this paper, we investigate the effects of ball-milling and UV irradiation on two species of softwood and two species of hardwood, using X-ray diffractometry (XRD), evolved gas analysis-mass spectrometry (EGA-MS), and pyrolysis-gas chromatography coupled to mass spectrometry (Py-GC/MS). The XRD data showed that the crystalline fraction of cellulose was destroyed by milling, but not by irradiation. The EGA-MS data and isoconversional kinetic analysis showed that both milling and irradiation can reduce the thermal stability of wood up to a limit value. The Py-GC/MS data showed that irradiation caused the most significant changes in the pyrolytic behavior of the wood species, increasing the ratio of holocellulose to lignin pyrolysis products and the reactivity of cellulose toward the derivatizing agent. Softwoods were more affected by irradiation than hardwoods. This paper shows that UV irradiation can decrease the recalcitrance of biomass toward pyrolysis, but its efficiency is highly dependent on the type of lignocellulosic substrate.

This research presents a 100% renewable energy (RE) scenario by 2050 with a high share of electric vehicles on the grid (V2G) developed in Ecuador with the support of the EnergyPLAN analysis tool. Hour-by-hour data iterations were performed to determine solutions among various features, including energy storage, V2G connections that spanned the distribution system, and long-term evaluation. The high participation in V2G connections keeps the electrical system available; meanwhile, the high proportions of variable renewable energy are the pillar of the joint electrical system. The layout of the sustainable mobility scenario and the high V2G participation maintain the balance of the electrical system during most of the day, simplifying the storage equipment requirements. Consequently, the influence of V2G systems on storage is a significant result that must be considered in the energy transition that Ecuador is developing in the long term. The stored electricity will not only serve as storage for future grid use. Additionally, the V2G batteries serve as a buffer between generation from diversified renewable sources and the end-use stage.

Research on corona discharge, shared by physics, chemistry and electrical engineering, has not arrested yet. As a dissipative process, the development of corona increases the resistive losses of transmission lines and enhances the line capacitance locally. Introducing additional losses and propagation delay, along the line, non-linearity and non-uniformity of the line parameters; therefore, corona should not be neglected. The present work is meant to provide the reader with comprehensive information on the corona macroscopic phenomenology and development, referring to the most relevant contributions in the literature on this subject. The models proposed in the literature for the simulation of the corona development are reviewed in detail, and sensitivity curves are provided to highlight their dependence on the input parameters.