• Energy Research
• Open Access close
• Restricted close
• natural sciences close
• US close
• DE close

Abstract With the rapid advancement in wearable electronics, energy harvesting devices based on triboelectric nanogenerators (TENGs) have been intensively investigated for providing sustainable power supply for them. However, the fabrication of wearable TENGs still remains great challenges, such as flexibility, breathability and washability. Here, a route to develop a new kind of woven-structured triboelectric nanogenerator (WS-TENG) with a facile, low-cost, and scalable electrospinning technique is reported. The WS-TENG is fabricated with commercial stainless-steel yarns wrapped by electrospun polyamide 66 nanofiber and poly(vinylidenefluoride-co-trifluoroethylene) nanofiber, respectively. Triggered by diversified friction materials under a working principle of freestanding mode, the open-circuit voltage, short-circuit current and maximum instantaneous power density from the WS-TENG can reach up to 166 V, 8.5 µA and 93 mW/m2, respectively. By virtue of high flexibility, desirable breathability, washability and excellent durability, the fabricated WS-TENG is demonstrated to be a reliable power textile to light up 58 light-emitting diodes (LED) connected serially, charge commercial capacitors and drive portable electronics. A smart glove with stitched WS-TENGs is made to detect finger motion in different circumstances. The work presents a new approach for self-powered textiles with potential applications in biomechanical energy harvesting, wearable electronics and human motion monitoring.

Climate change, environmental degradation, and limited resources are motivations for sustainable forest management. Forests, the most abundant renewable resource on earth, used to make a wide variety of forest-based products for human consumption. To provide a scientific measure of a product’s sustainability and environmental performance, the life cycle assessment (LCA) method is used. This article provides a comprehensive review of environmental performances of forest-based products including traditional building products, emerging (mass-timber) building products and nanomaterials using attributional LCA. Across the supply chain, the product manufacturing life-cycle stage tends to have the largest environmental impacts. However, forest management activities and logistics tend to have the greatest economic impact. In addition, environmental trade-offs exist when regulating emissions as indicated by the latest traditional wood building product LCAs. Interpretation of these LCA results can guide new product development using biomaterials, future (mass) building systems and policy-making on mitigating climate change. Key challenges include handling of uncertainties in the supply chain and complex interactions of environment, material conversion, resource use for product production and quantifying the emissions released.

Abstract This article is a survey of the theoretical questions arising in the development of a convergence theory and error analysis of synthesis methods for solving neutron diffusion problems. For simplicity, we discuss convergence and the error analysis for spectral synthesis methods, in which the trial functions are functions solely of energy. The diffusion coefficient, the total and scattering cross-section data for the diffusion model are assumed spatially and energy dependent, and interior interfaces (i.e. spatial discontinuities in the diffusion coefficient and cross-section data) are present. The boundary conditions imposed are homogeneous Dirichlet conditions.

The Social-Ecological Systems (SES) framework serves as a valuable framework to explore and understand social and ecological interactions, and pathways in water governance. Yet, it lacks a robust understanding of change. We argue an analytical and methodological approach to engaging global changes in SES is critical to strengthening the scope and relevance of the SES framework. Relying on SES and resilience thinking, we propose an institutional and cognitive model of change that institutions and natural resources systems co-evolve to provide a dynamic understanding of SES that stands on three causal mechanisms: institutional complexity trap, rigidity trap, and learning processes. We illustrate how Data Cube technology could overcome current limitations and offer reliable avenues to test hypothesis about the dynamics of social-ecological systems and water security by offering to combine spatial and time data with no major technical requirements for users.

AbstractMembrane Technology and Research, Inc. has proposed a hybrid system combining amine scrubbing with membrane technology to reduce energy cost. Previous studies of CO2 absorption mainly focused on coal-fired flue gas with 12% CO2. However, in the hybrid process, the CO2 in the flue gas can be enriched to 20%. Natural gas turbines will have flue gas with as little as 3% CO2。 Based on the arrangement, the hybrid amine/membrane system provides a gas to the system that has double the CO2 concentration of normal flue gas, reduces the volume of gas sent to the capture unit, or reduces the removal requirements for the capture unit.The objective of this work is to minimize the total energy use of stripping concentrated piperazine (PZ) at rich loading when treating flue gas from 3 to 20% inlet CO2. The base-case stripping configuration is the advanced flash stripper with warm rich bypass and cold rich exchanger bypass. . This configuration includes two split cross-exchangers in series, a convective steam heater, a smaller stripper column, a low residence time flash tank, and stripping at high temperature to produce CO2 at 5 to 17bar. Rich loading in 5 and 8m PZ was varied from 0.37 to 0.43mol CO2/mol N. For each rich loading, lean loading was optimized to minimize the total equivalent work. The “Independence” model for PZ in Aspen Plus® was used to simulate the stripping performance.Because 5m PZ has a lower viscosity than 8m PZ, it can achieve a reduced approach temperature in the cross exchanger. The total energy performance for 5m PZ is practically the same as 8m PZ, even though the capacity of 5m PZ is lower. Significantly more energy is required to regenerate solvents with lower rich loading. As CO2 rich loading increases, the equivalent work requirement decreases for the same loading difference between rich and lean.Stripping data for 24 cases, including heat duty, equivalent work, CO2 output pressure, and optimal cold and warm rich bypass were used to build a correlation with CO2 rich and lean loading. The Second Law efficiency based on the ratio of stripping minimum work and total ideal work was introduced to make the most of stripping work. The Second Law efficiency has a maximum value at a specific CO2 loading.

Flexible butyl interconnection segments are synthetically incorporated into an electronically conductive poly(pyrene methacrylate) homopolymer and its copolymer. The insertion of butyl segment makes the pyrene polymer more flexible, and can better accommodate deformation. This new class of flexible and conductive polymers can be used as a polymer binder and adhesive to facilitate the electrochemical performance of a silicon/graphene composite anode material for lithium ion battery application. They act like a “spring” to maintain the electrode mechanical and electrical integrity. High mass loading and high areal capacity, which are critical design requirements of high energy batteries, have been achieved in the electrodes composed of the novel binders and silicon/graphene composite material. A remarkable area capacity of over 5 mAh/cm2 and volumetric capacity of over 1700 Ah/L have been reached at a high current rate of 333 mA/g.

A major achievement in research supported by the Kluane Lake Research Station was the recovery, in 2001 – 02, of a suite of cores from the icefields of the central St. Elias Mountains, Yukon, by teams of researchers from Canada, the United States, and Japan. This project led to the development of parallel, long (103 – 104 year) ice-core records of climate and atmospheric change over an altitudinal range of more than 2 km, from the Eclipse Icefield (3017 m) to the ice-covered plateau of Mt. Logan (5340 m). These efforts built on earlier work recovering single ice cores in this region. Comparison of these records has allowed for variations in climate and atmospheric composition to be linked with changes in the vertical structure and dynamics of the North Pacific atmosphere, providing a unique perspective on these changes over the Holocene. Owing to their privileged location, cores from the St. Elias Icefields also contain a remarkably detailed record of aerosols from various sources around or across the North Pacific. In this paper we review major scientific findings from the study of St. Elias Mountain ice cores, focusing on five main themes: (1) The record of stable water isotopes (δ18O, δD), which has unique characteristics that differ from those of Greenland, other Arctic ice cores, and even among sites in the St. Elias; (2) the snow accumulation history; (3) the record of pollen, biomass burning aerosol, and desert dust deposition; (4) the record of long-range air pollutant deposition (sulphate and lead); and (5) the record of paleo-volcanism. Our discussion draws on studies published since 2000, but based on older ice cores from the St. Elias Mountains obtained in 1980 and 1996.