• Energy Research
• Closed Access close
• US close
• DE close
• Solar Energy close

Abstract Thermal performance of three naturally ventilated public buildings in which the wind tower is an important architectural freature is studied. One of the three builidings as well as it's wind tower is instrumented for temperature, relative humidity and airflow velocity measurements, and the other two are instrumented for temperature measurement. The results have led to a discussion concerning the degree of wind tower effectiveness in achieving thermal comfort.

Abstract Solar water evaporation has been a topic of interest in recent years due to its applications in desalination, power generation, and heating. As water is not a good absorber of light, seeding it with light-absorbing particles can enhance evaporation efficiency. Activated carbon (AC) is one such material with desirable absorption properties for this application. However, particle sizes in granular and powder activated carbon can vary significantly. In this work, AC particles of different sizes are analyzed and their effect on evaporation rate is studied. It is found that particle sizes less than or comparable to solar wavelength spectrum produce higher evaporation efficiencies under independent scattering conditions ( f v 0.6 % ). It is also found that the solar absorption coefficient reaches between 0.98 and 0.9 for a volume fraction as low as 0.01%. The evaporation efficiency is 57.3% and 38.2% higher than for pure water evaporation for size of 80 nm and 8 μm, respectively, for a volume fraction of 0.01%. A parametric analysis is performed to identify the respective effect on evaporation rate.

Abstract Recently bifacial n-type passivated emitter and rear totally diffused (PERT) monocrystalline silicon solar cells have become one hot spot in photovoltaic (PV) industries, due to good bifaciality, high and stabilised conversion efficiency. Unlike passivated emitter and rear contacts (PERC) structure, n-PERT solar cells require the use of a thin and uniform back surface field (BSF) layer, usually achieved by phosphorus doping. In this study, we optimised the phosphorus diffusion process in terms of surface concentration, junction depth and carrier lifetime. The effects of different phosphorus BSF were investigated by fabricating n-type front and back contact (nFAB) PERT solar cells using industrial feasible approaches and M2 size Czochralski (Cz) monocrystalline Si wafers (6 in., 244.32 cm2). Good phosphorus profiles were developed, which gives low parasitic absorption, low contact resistance and low J0 value when passivated with silicon nitride (SiNx) layer. The optimised champion cell shows a high Voc of 666.5 mV, Jsc of 40.2 mA/cm2, fill factor of 79.9%, efficiency of 21.43% from front side-illumination, together with a good bifaciality factor of 93.0%.

Abstract Cu2BaSn(S,Se)4 (CBTSSe) solar cells are emerging photovoltaic devices due to their high theoretical efficiencies of ~31%, environment-friendly and earth-abundant composition, low density of non-recombination defects, and so on. However, the record efficiency of CBTSSe solar cell is only 5.2%, showing the importance of studying their performance via numerical analysis to further enhance their practical efficiencies. In this paper, the effect of absorber and buffer layers on performances of Cu2BaSnS4 (CBTS) solar cells are firstly systematically studied via the SCAPS-1D software to provide a platform for the study of the effect of MoS2 interlayer on the performances of CBTS solar cells. The highest PCE of CBTS solar cell with a 30 nm CdS buffer layer is 11.87%. The PCE of CBTS solar cell with a 0.8 μm CBTS absorb layer is 12.51%, indicating that the CBTS solar cell is a potential low-cost solar cell due to its large optical absorption coefficient (α > 104 cm−1). The efficiency of CBTS solar cell is improved to 16.47% when the carrier concentration of CBTS is 1016 cm−3. The relationship between the performance of solar cell and the band gap, thickness, donor concentration, acceptor concentration of MoS2 interlayer is systematically investigated on the basis of the optimized efficiency. It is found that MoS2 interlayer plays an important role in the performance of CBTS solar cell. The p-type MoS2 has a beneficial effect on the efficiency improvement while the n-type MoS2 has a negative effect on the efficiency enhancement. The highest PCE of CBTS solar cell is as high as 18.28% when the thickness and the acceptor concentration of MoS2 are 4 nm and 1019 cm−3, respectively. Our simulation result provides a promising research direction to further improve the actual efficiency of the CBTS solar cell.

This paper reports a facile method to prepare a textured surface with combined micron- and nano-scale surface features, which is used as master for nano-imprinting process to obtain transparent front electrodes in thin-film silicon tandem cells. The micron- and nano-scale surface features of the master are formed by combination of SiO2 sphere pre-deposition and ZnO textured growth. The master exhibits an averaged total transmittance value of 89.7% and an averaged haze value of 54.1% for the wavelength from 380 to 1100 urn. Comparing to the flat reference cell, the thin-film Si tandem cell deposited on the superstrate prepared using this master shows substantial decrease in reflectance at long wavelengths and drastic gain in the photocurrent of the bottom cell, the maximum summed current is enhanced by 35.5%, and the convert efficiency is improved from 8% to 10.0 +/- 0.3%. (C) 2015 Elsevier Ltd. All rights reserved.

Abstract In this paper, the experimental performance of a 45 m2 solar field of non-tracking external compound parabolic (XCPC) collectors installed at the University of California, Merced is described. The solar field was operated during July-August 2020 in both clean and dirty conditions and at varying operating temperatures (70, 135, 170 °C) while operating an air heater, thermal evaporator, and double effect absorption chiller. Performance data was used to develop an instantaneous solar field performance model which was then incorporated into an annual performance model using TMY3 data to estimate yearly production from the solar field. The model predicts an annual generation of ∼1100 kWh/m2-year at 80 °C, ∼1000 kWh/m2-year at 100 °C, ∼900 kWh/m2-year at 120 °C, ∼800 kWh/m2-year at 140 °C, and ∼700 kWh/m2-year at 160 °C in California. The XCPC technology is currently expected to have an installed cost of $300/m2 and an annual operations and maintenance cost of $6.5/m2-year. Over a 25 year lifetime it provides a levelized cost of heat at 2–4 cents per kWhth delivered. This is below the cost of commercial natural gas in California and at temperatures ≤ 120 °C below the cost of industrial natural gas, which highlights the potential of the XCPC technology for decarbonizing thermal applications such as water and space heating, drying, sterilization, desalination, evaporation, low pressure steam, double effect absorption chilling, process heating, and more. The lifetime cost of emissions reductions is ∼$169 per metric ton of avoided CO2 when replacing natural gas, ∼$137/MT CO2 when replacing propane, and ∼$83/MT CO2 when replacing electric heating.

Abstract This paper presents information comparing three transparent plastic films with glass as glazings for solar energy absorption collectors. Data concerning the transmittance characteristics of these films are included, together with information concerning other physical properties such as tensile strength, index of refraction, and weathering characteristics.

Abstract Flux profiles of the sun image were measured at the focus of the California Institute of Technology lens-type solar furnace using NRDL water-cooled radiometers. A maximum flux value of 220 cal per sec per sq cm was recorded when the direct solar radiation received at the furnace site was 1.04 cal per min per sq cm. Under these conditions, the furnace operating efficiency was found to be 47.2 per cent. The losses of 52.8 per cent are ascribed to transmission losses in the lenses, reflectivity losses at the mirrors, the geometrical imperfection of the individual lenses and mirrors, and lack of perfect superposition of the nineteen sets of images.