• Energy Research
• Closed Access close
• Restricted close
• Embargo close
• 12. Responsible consumption close
• US close
• DE close

Purpose This study aims to consider environmental sustainability, a global challenge under the preview of sustainable development goals, highlighting the significance of knowledge economy in attaining sustainable aggregate demand behavior globally. For this purpose, 155 countries that have data available from 1995 to 2021 were selected. The purpose of selecting these countries is to test the global responsibility of the knowledge economy to attain environmental sustainability. Design/methodology/approach Results are estimated with the help of panel quantile regression. The empirical existence of aggregate demand-based environmental Kuznets curve (EKC) was tested using non-linear tests. Moreover, principal component analysis has been incorporated to construct the knowledge economy index. Findings U-shaped aggregate demand-based EKC at global level is validated. However, environmental deterioration increases with an additional escalation after US$497.945m in aggregate demand. As a determinant, the knowledge economy is reducing CO2 emissions. The knowledge economy has played a significant role in global responsibility, shifting the EKC downward and extending the CO2 reduction phase for every selected country. Further, urbanization, energy intensity, financial development and trade openness significantly deteriorate the environmental quality. Originality/value This study contains the empirical existence of aggregate demand-based EKC. The role of the knowledge economy is examined through an index which is calculated by using four pillars of the knowledge economy (technology, innovations, education and institutions). This study is based on a combined panel of all the countries for which the data was available.

Paper mill sludge (PMS) is a residual biomass that is generated at paper mills in large quantities. Currently, PMS is commonly disposed in landfills, which causes environmental issues through chemical leaching and greenhouse gas production. In this research, we are exploring the potential of fast pyrolysis process for converting PMS into useful bio-oil and biochar products. We demonstrate that by subjecting PMS to a combination of acid hydrolysis and torrefaction pre-treatment processes it is possible to alter the physicochemical properties and composition of the feedstock material. Fast pyrolysis of pretreated PMS produced bio-oil with significantly higher selectivity to levoglucosenone and significantly reduced the amount of ketone, aldehyde, and organic acid components. Pretreatment of PMS with combined 4% mass fraction phosphoric acid hydrolysis and 220 °C torrefaction processed prior to fast pyrolysis resulted in a 17 times increase of relative selectivity towards levoglucosenone in bio-oil product along with a reduction of acids, ketones, and aldehydes combined from 21 % to 11 %. Biochar, produced in higher yield, has characteristics that potentially make the solid byproduct ideal for soil amendment agent or sorbent material. This work reveals a promising process system to convert PMS waste into useful bio-based products. More in-depth research is required to gather more data information for assessing the economic and sustainability aspects of the process.

Bioplastics are alternatives of conventional petroleum-based plastics. Bioplastics are polymers processed from renewable sources and are biodegradable. This study aims at conducting an environmental impact assessment of the bioprocessing of agricultural wastes into bioplastics compared to petro-plastics using an LCA approach. Bioplastics were produced from potato peels in laboratory. In a biochemical reaction under heating, starch was extracted from peels and glycerin, vinegar and water were added with a range of different ratios, which resulted in producing different samples of bio-based plastics. Nevertheless, the environmental impact of the bioplastics production process was evaluated and compared to petro-plastics. A life cycle analysis of bioplastics produced in laboratory and petro-plastics was conducted. The results are presented in the form of global warming potential, and other environmental impacts including acidification potential, eutrophication potential, freshwater ecotoxicity potential, human toxicity potential, and ozone layer depletion of producing bioplastics are compared to petro-plastics. The results show that the greenhouse gases (GHG) emissions, through the different experiments to produce bioplastics, range between 0.354 and 0.623 kg CO2 eq. per kg bioplastic compared to 2.37 kg CO2 eq. per kg polypropylene as a petro-plastic. The results also showed that there are no significant potential effects for the bioplastics produced from potato peels on different environmental impacts in comparison with poly-β-hydroxybutyric acid and polypropylene. Thus, the bioplastics produced from agricultural wastes can be manufactured in industrial scale to reduce the dependence on petroleum-based plastics. This in turn will mitigate GHG emissions and reduce the negative environmental impacts on climate change.

This paper develops a strategy for the continuing and improved supply of woodfuels to urban and industrial consumers in Sub-Sahara Africa. It argues that continued use of these fuels is not only a necessity, but is also in the best economic interest of most of the countries in this region. It shows that intensified and more orderly utilization of woodfuels can help to enhance, rather than impinge upon environmental parameters. Some examples are provided that illustrate how such strategies can be put into practice.

This paper presents experimental results of the impact of CO(2) co-feed on a gasification/pyrolysis process for various feedstocks (biomass, coal, and municipal solid waste (MSW)). Various feedstocks were thermo-gravimetrically characterized under various atmospheric conditions and heating rates. A substantial amount of char burn out was identified in the presence of CO(2) via a series of thermo-gravimetric analysis tests, which enabled high conversion of final mass (approximately 99%) to be achieved. The impact of CO(2) co-feed on the volatilization regime during the pyrolysis/gasification process was not apparent at a heating rate of 10-40 degrees C min(-1). However, the impact of CO(2) on the volatilization regime at a fast heating rate (950 degrees C min(-1)) was substantial. For example, significant enhancement in the generation of CO, by a factor of approximately 2, was observed in the presence of CO(2). The generation of major chemical species, such as CH(4) and C(2)H(4), were enhanced, but this was not as apparent as in the case with CO. In addition, introducing CO(2) to the pyrolysis/gasification process enabled the amount of condensable liquid hydrocarbons, such as tar (approximately 30-40%) to be significantly reduced in the presence of CO(2), in that injecting CO(2) into the pyrolysis/gasification process expedites cracking the volatilized chemical species. Experimental work confirmed that biomass and MSW could be feasible and desirable feedstocks for the pyrolysis/gasification process as these feedstocks can be easily treated compared to coal. To extend this understanding to a more practical level, various feedstocks were tested in a tubular reactor and drop tube reactor under various experimental conditions.

Bioenergy is considered a sustainable substitute to fossil-fuel resources and the development of a prudent combination of renewable and innovative conversion technologies are essential for the valorization and effective conversion of biowaste to value-added commodities. Here, a negative pressure-induced carbonization process was proposed for the valorization of lignin-enriched biowaste precursor to bio-oil and environmental materials (biochar) at various temperatures. The high heating values (HHV) of the as-prepared biochars from the lignin enriched precursor under negative pressure (low-medium vacuum) were within 25.9-31.5 MJ/kg, which matched satisfactorily to the commercial charcoal. Whereas, the bio-oils produced from the lignin enriched precursor under vacuum conditions was a blend of complex aromatic and straight-chain hydro-carbons, including aldehyde, ketone, phenol, and furans, exhibiting ability as potential heating-oil with HHV within 21.2-28.2 MJ/kg. Moreover, the biochars produced under vacuum environments at higher temperature showed greater stability (22.5-35.9%) than those produced under N2 atmosphere.

A promising route to transition wastewater treatment facilities (WWTFs) from energy-consuming to net energy-positive is to retrofit existing facilities with process modifications, residual biosolid upcycling, and effluent thermal energy recovery. This study assesses the economics and life cycle environmental impacts of three proposed retrofits of WWTFs that consider thermochemical conversion technologies, namely, hydrothermal liquefaction, slow pyrolysis, and fast pyrolysis, along with advanced bioreactors. The results are in turn compared to the reference design, showing the retrofitting design with hydrothermal liquefaction, and an up-flow anaerobic sludge blanket has the highest net present value (NPV) of $177.36MM over a 20-year plant lifetime despite 15% higher annual production costs than the reference design. According to the ReCiPe method, chlorination is identified as the major contributor for most impact categories in all cases. There are several uncertainties embedded in the techno-economic analysis and life cycle assessment, including the discount rate, capital investment, sewer rate, and prices of main products; among which, the price of biochar presents the widest variation from $50 to $1900/t. Sensitivity analyses reveal that the variation of discount rates causes the most significant changes in NPVs. The impact of the biochar price is more pronounced in the slow pyrolysis-based pathway compared to the fast pyrolysis since biochar is the main product of slow pyrolysis.

Abstract Bamboo has been considered a potential feedstock of energy for the future. It can be subjected to the pyrolysis for biofuels production. The thermogravimetric analysis (TGA) combined with differential thermogravimetric analysis (DTG) for bamboo was carried out prior to pyrolysis. The thermal degradation of bamboo was mainly between 230 and 420 °C. The conventional pyrolysis of bamboo was investigated in a bubbling fluidized-bed reactor using silica sand. The product distribution and composition of pyrolysis bio-oil were dependent on biomass component and operating conditions such as pyrolysis temperature, fluidization velocity, and particle size of biomass. The fractional catalytic pyrolysis of bamboo was also studied to upgrade the pyrolysis vapor, using HZSM-5 and red mud. The highest yield of bio-oil was 54.03 wt% compared to 49.14 wt% and 50.34 wt% of HZSM-5 and red mud catalyst, respectively. In the red mud catalytic pyrolysis, the oxygen content was rejected from pyrolysis vapor mostly via decarboxylation to produce more CO2 than CO; in contrast, for the HZSM-5 catalytic pyrolysis, the production of CO through decarbonylation was more favored than CO2. The main composition of catalytic pyrolysis bio-oil was 4-vinylphenol, which was employed as a raw material source to synthesize valuable material for energy storage.

Abstract The absorption refrigeration system driven by low grade heat sources, especially the waste heat sources, becomes more and more attractive in recent decades. However, most traditional absorption systems cannot achieve a high utilization rate of the waste heat with limited heat capacity. These systems are usually designed to obtain heat in the generator, which means that the waste heat sources cannot be utilized to the temperature lower than the generator temperature. This paper proposed a new structure heated by heat conduction oil in the generator and electric heating rings around the stripping section. This structure can simulate the temperature-distributed heat sources when the electric heating rings work. It can also simulate a traditional generator when the electric heating rings do not work. Influences of different heat distributions are analyzed in detail in this paper. The results show that the heat sources utilization rate will increase with the increase of the heat in the stripping section, while the coefficient of performance will be negatively affected by the increasing heat in the stripping section. By optimizing the heating structure, the coefficient of performance can be similar to that of a traditional system when the heat is just added in the middle and lower part of stripping section. The optimum utilization rate of heat sources in this test model can reach 1.8 times to that of a traditional system. Under this heating model, the lowest temperature required in the heating section is 82 °C when the heat conduction oil inlet temperature is 169 °C. It is much lower than the temperature inside the generator, which is 137.3 °C.