• Energy Research
• other engineering and technologies close
• CN close
• ES close

Abstract Previous studies have shown that titanium-based glazes containing silicon and calcium tend to crystallize into titanite. In this work, ZnO was found to be an effective additive to produce rutile but not titanite. Images of the micromorphology showed that the glaze doped with 8 wt% ZnO was UV–VIS–NIR of acicular rutile and granular silica. The refractive index of crystalline rutile is higher than that of crystalline titanite, which leads to higher reflectance in the near-infrared range. However, excessive rutile counteracted this improvement in the UV–VIS–NIR spectrum reflectance of solar energy because it decreased the visible spectrum reflectance. As a result, the best ratio of added ZnO was confirmed to be 2 wt%.

Particle receivers are gaining importance in the field of Concentrating Solar Power (CSP) due to the high temperature that particles can achieve without degradation. Several researchers are studying the potential of this technology by means of system analyses, which need simple and light models of the system. This study presents two simple models for the particle receiver. The simplest model is a correlation obtained by fitting the results calculated with a more complex receiver model simulated in CFD. The other model is a 1D model, which is benchmarked against the same CFD results. Although both models achieve high coefficient of determination, R2, when compared to CFD results, the 1D model seems to provide more accurate results (especially during sunsets and sunrises). Both models are integrated into a tecno-economic model developed in previous work. The LCOE obtained with the 1D model is between 7% and 10% greater than the one obtained with the correlation.

The most severe failures in power grids are often characterized as cascading failures where an initial event triggers consequent failures all along the grid often leading to blackouts. Upon identifying a failure and its cascade potential, timely control actions should be performed by the grid operators to mitigate the effect of the cascade. These actions have to be delivered to one or more control devices, creating a dependency between the power grid and its control network. This paper examines the dependency of the operation of the power grid on the control network. Different from literature studies on failure control, our dependency model captures the impact of networking parameters. We formulate an algorithmic model that describes the impact of this dependency on cascade control. Based on this model, we propose an efficient cascade control algorithm using load shedding with consideration of delays in the communication network for power grids. Finally, we evaluate the impact of the power-communication network dependency with uncontrolled grids, ideal/simple control grids and our proposed control scheme. The results demonstrate that the proposed algorithm can significantly reduce the failure of power lines while sustaining larger power demand for users.

This study focuses on formulating the most sustainable concrete by incorporating recycled concrete aggregates and other products retrieved from construction and demolition (C&D) activities. Both recycled coarse aggregates (RCA) and recycled fine aggregates (RFA) are firstly used to fully replace the natural coarse and fine aggregates in the concrete mix design. Later, the cement rich ultrafine particles, recycled glass powder and mineral fibres recovered from construction and demolition wastes (CDW) are further incorporated at a smaller rate either as cement substituent or as supplementary additives. Remarkable properties are noticed when the RCA (4–12 mm) and RFA (0.25–4 mm) are fully used to replace the natural aggregates in a new concrete mix. The addition of recycled cement rich ultrafines (RCU), Recycled glass ultrafines (RGU) and recycled mineral fibres (RMF) into recycled concrete improves the modulus of elasticity. The final concrete, which comprises more than 75% (wt.) of recycled components/materials, is believed to be the most sustainable and green concrete mix. Mechanical properties and durability of this concrete have been studied and found to be within acceptable limits, indicating the potential of recycled aggregates and other CDW components in shaping sustainable and circular construction practices. The authors wish to acknowledge the financial support from EU Horizon 2020 Project VEEP ‘‘Cost-Effective Recycling of C&DW in High Added Value Energy Efficient Prefabricated Concrete Compo-nents for Massive Retrofitting of our Built Environment” (No.723582).

Experimental investigation into the effects of different pilot amounts of dimethyl ether (DME) on the performance and emission of a single-cylinder directinjection DME engine is conducted. The results show that a DME engine can operate at a wider range of speeds and loads at quasi-homogenous charge compression ignition (QHCCI) mode. The brake thermal efficiency increases while the exhaust temperature decreases. NOx emission decreases by about 30%–50% although there is a slight increase in HC and CO emissions. NOx, HC and CO emissions increase with an increase in the amount of DME pilot. QHCCI is a good way to increase thermal efficiency and decrease NOx emission.

Abstract Predicting and optimizing radiative thermal properties have been acknowledged as an efficient way to improve thermal insulation performance of fibrous materials with high porosity. Based on experimental investigation of infrared spectral of ultrafine fibrous insulations with diameters of 520–650 nm, a method of calculating radiative thermal properties was presented by combining Rosseland equation, Mie scattering theory, Beer’s law and Subtractive Kramers–Kronig (SKK) relation. To ensure the calculation correct the uniqueness analysis was performed for Poly(vinylidene fluoride) (PVDF) fibers, which indicated the valid fiber diameter was less than 1.06 μm. The calculated thermal radiative conductivities by using the method agreed well with the measured data. The effect of fiber diameter on the thermal properties of the fibrous insulations was also investigated to minimize the radiative thermal conductivity. The results indicated that the minimized radiative thermal conductivities by regulating fiber diameters could be approximately 25% smaller than those for experimental fiber diameters. The method of predicting and minimizing radiative thermal conductivities of fibrous insulations demonstrated in this paper could be of great advantage to thermal engineering applications aiming to reducing heat loss and saving energy.

In this paper, a numerical method coupling moment method with circuit theory is used to analyze the influence of the grounding material's property on the performance of grounding grids. It can be seen that for a large grounding grid, when the soil resistivity is small, the influence of both resistivity and permeability of grounding material on the performance of grounding grids is great. If the frequency is not very high, the grounding material's resistivity can affect the performance of the grounding grid obviously. If the frequency is very low or very high, the effect of the grounding material's permeability on the performance of the grounding grid is small, while the effect is obvious at other frequency.

Reactive power consumption of the modern power system is a very important problem that to solve well. Due to the line commutated current source converter-based (LCC) HVDC system is a multivariable and strong coupling nonlinear system, it is difficult to model reactive power consumption of receiving end of LCC-HVDC by traditional analysis method. This paper proposes the reactive power consumption model of receiving end of LCC-HVDC on account of the radial basis function (RBF) neural network. The model with the turn-off angle for input, with reactive power loss on the inverter side of LCC-HVDC for output, using 500kV, 1000MW LCC-HVDC system PSCAD simulation test data training RBF neural network and testing network generalization ability. The results indicate that the reactive power loss model on account of the RBF neural network has much faster convergence speed and higher convergence precision.