• Energy Research
• 7. Clean energy close
• 11. Sustainability close
• DE close
• ES close
• EU close

Dataset supporting publication: “A novel ROM methodology to support the estimation of the energy savings under the Measurement and Verification protocol” (publication available for download: GEOFIT Zenodo) Datasets resultant from simulation of the integrated system into buildings. Conference paper presented in IBPSA-England Building Simulation and Optimisation Conference 2020 This paper presents a novel Reduced Order grey box Model (ROM) methodology, based on a Resistor-Capacitor (RC) network, which supports the creation of the baseline energy consumption and the estimation of energy savings due to Energy Conservation Measures (ECMs) under the Measurement and Verification protocol. Within this scope, a description of the RC network, including a calculation of the parameters’ needed to execute the ROM, are presented. This ROM methodology is demonstrated on an educational building located in Sant Cugat, Spain as part of the H2020 GEOFIT project. The results presented in this paper demonstrate that the ROM is sufficiently accurate for the creation of the baseline energy consumption and for estimating the energy savings of different ECMs.

This dataset was prepared by TNO as a contribution to the H2020 project CHE and the H2020 project VERIFY. The basis is a high-resolution (~1x1 km) emission inventory providing CO2 and CO (from fossil fuels and biofuels separately) over western Europe (2ºW - 19ºE, 47ºN - 56ºN). The reported emissions by European countries to UNFCCC (CO2) and to EMEP/CEIP (CO) have been used and where needed gap-filled or replaced with emission data from the GAINS model. These country-level emissions are disaggregated in space using a consistent spatial distribution methodology, whereas large point sources are listed with their exact locations. This approach is similar to the one described by Kuenen et al., (ACP, 2014). Emissions are reported per GNFR sector, with an extra split for road transport. The emission grids that are part of this dataset are a variation on the base grid, representing the uncertainty in the emission data. Each grid is equally plausible. The grids have been created using a Monte Carlo approach. The uncertainties in the underlying data used to create the base grid (emissions: activity data and emission factors, spatial proxies) have been collected (either from country reports or based on expert judgement). Through the Monte Carlo simulation these uncertainties, taking into account error correlations between some sub-sectors, are combined to create ten new emission grids. The spread in emissions between these emission maps gives an indication of the uncertainty in the emissions. The grid files (in .csv and .nc format) contain annual total emissions per grid cell for the year 2015. A separate file has been prepared for each ensemble member in the Monte Carlo simulation (indicated with M). The unit in the files is kg/yr. A detailed description of the Monte Carlo simulation is presented in: Super, I., Dellaert, S. N. C., Visschedijk, A. J. H., and Denier van der Gon, H. A. C.: Uncertainty analysis of a European high-resolution emission inventory of CO2 and CO to support inverse modelling and network design, Atmos. Chem. Phys. Discuss., https://doi.org/10.5194/acp-2019-696, in review, 2019. N.B. It is important to note that 10 maps are not sufficient to describe the sometimes complex uncertainty structures, for example in the case of lognormal uncertainty distributions. The interpretation of the uncertainty based on these 10 maps should therefore be done with care. NB. Despite efforts to prevent negative emissions to occur in the grid maps, some negative values are still present. In local studies this might cause some issues, and we recommend to set negative emissions to zero in those cases.

Three data files are provided for Case Study 1 in the openENTRANCE project: Full_potential.V9.csv, metaData.Full_Potential.csv, and acheivable_NUTS2_summary.csv. The data covers 10 residential devices on the NUTS2 level for the EU27 + UK +TR + NO + CH from 2020-2050. The devices included are storage heater, water heater with storage capabilitites, air conditiong, heat circulation pump, air-to-air heat pump, refreigeration (includes refrigerators and freezers), dish washer, washing machine, and tumble drier. Full_potential.V9.csv shows the NUTS2 level unadjusted loads for residential storage heater, water heater, air conditiong, circulation pump, air-to-air heat pump, refreigeration (includes refrigerators and freezers), dish washer, washing machine, and tumble drier using representative hours from 2020-2050. The loads provided here have not been adjusted with the direct load participation rates (see paper for more details). More details on the dataset can be found in the metaData.Full_Potential.csv file. The acheivable_NUTS2_summary.csv shows the NUTS2 level acheivable direct load control potentials for the average hour in the respective year (years - 2020, 2022,2030,2040, 2050).

Project: Coupled Model Intercomparison Project Phase 6 (CMIP6) datasets - These data have been generated as part of the internationally-coordinated Coupled Model Intercomparison Project Phase 6 (CMIP6; see also GMD Special Issue: http://www.geosci-model-dev.net/special_issue590.html). The simulation data provides a basis for climate research designed to answer fundamental science questions and serves as resource for authors of the Sixth Assessment Report of the Intergovernmental Panel on Climate Change (IPCC-AR6). CMIP6 is a project coordinated by the Working Group on Coupled Modelling (WGCM) as part of the World Climate Research Programme (WCRP). Phase 6 builds on previous phases executed under the leadership of the Program for Climate Model Diagnosis and Intercomparison (PCMDI) and relies on the Earth System Grid Federation (ESGF) and the Centre for Environmental Data Analysis (CEDA) along with numerous related activities for implementation. The original data is hosted and partially replicated on a federated collection of data nodes, and most of the data relied on by the IPCC is being archived for long-term preservation at the IPCC Data Distribution Centre (IPCC DDC) hosted by the German Climate Computing Center (DKRZ). The project includes simulations from about 120 global climate models and around 45 institutions and organizations worldwide. Summary: These data include the subset used by IPCC AR6 WGI authors of the datasets originally published in ESGF for 'CMIP6.DAMIP.MPI-M.MPI-ESM1-2-LR' with the full Data Reference Syntax following the template 'mip_era.activity_id.institution_id.source_id.experiment_id.member_id.table_id.variable_id.grid_label.version'. The MPI-ESM1.2-LR climate model, released in 2017, includes the following components: aerosol: none, prescribed MACv2-SP, atmos: ECHAM6.3 (spectral T63; 192 x 96 longitude/latitude; 47 levels; top level 0.01 hPa), land: JSBACH3.20, landIce: none/prescribed, ocean: MPIOM1.63 (bipolar GR1.5, approximately 1.5deg; 256 x 220 longitude/latitude; 40 levels; top grid cell 0-12 m), ocnBgchem: HAMOCC6, seaIce: unnamed (thermodynamic (Semtner zero-layer) dynamic (Hibler 79) sea ice model). The model was run by the Max Planck Institute for Meteorology, Hamburg 20146, Germany (MPI-M) in native nominal resolutions: aerosol: 250 km, atmos: 250 km, land: 250 km, landIce: none, ocean: 250 km, ocnBgchem: 250 km, seaIce: 250 km.

Data reported by companies on the production, import, export, destruction and feedstock use of fluorinated greenhouse gases in the European Union during the years 2007-2019. The primary data is synthesised and aggregated at EU level and used to assess the progress on HFC phase-down made under both EU legislation and the UN framework as part of the Kigali Amendment to the Montreal Protocol. The data also details the amount of F-gases supplied to various industrial applications.

This data contents information about parental wood and charcoal characteristics of 16 tropical species growing in fast-growth condictions. The data details tha following characterist of parental wood: moisture content (PMC) and wood density (PWD). On the others hand the charcoal characteristics are: Density (CD), moisture content (CMC) and compression strength of charcoal, gross calorific value (GCV), ash and volatile matter and fixed carbon, Carbon (C), nitrogen (N), hydrogen (H), and oxygen (O) contents, C/N ratio, O/Cmol ratio and H/Cmol ratio. Besides it is presented FTIR spectra and the ignition temperature (Ti), the burnout temperature (Tf), the characteristic combustion index (S), the ignition index (Di), the time corresponding to the maximum combustion rate (tp), the ignition time (tig), and the average rate of combustion.

Abstract With the rapid advancement in wearable electronics, energy harvesting devices based on triboelectric nanogenerators (TENGs) have been intensively investigated for providing sustainable power supply for them. However, the fabrication of wearable TENGs still remains great challenges, such as flexibility, breathability and washability. Here, a route to develop a new kind of woven-structured triboelectric nanogenerator (WS-TENG) with a facile, low-cost, and scalable electrospinning technique is reported. The WS-TENG is fabricated with commercial stainless-steel yarns wrapped by electrospun polyamide 66 nanofiber and poly(vinylidenefluoride-co-trifluoroethylene) nanofiber, respectively. Triggered by diversified friction materials under a working principle of freestanding mode, the open-circuit voltage, short-circuit current and maximum instantaneous power density from the WS-TENG can reach up to 166 V, 8.5 µA and 93 mW/m2, respectively. By virtue of high flexibility, desirable breathability, washability and excellent durability, the fabricated WS-TENG is demonstrated to be a reliable power textile to light up 58 light-emitting diodes (LED) connected serially, charge commercial capacitors and drive portable electronics. A smart glove with stitched WS-TENGs is made to detect finger motion in different circumstances. The work presents a new approach for self-powered textiles with potential applications in biomechanical energy harvesting, wearable electronics and human motion monitoring.

Abstract Secondary concentrators are used in solar concentrating systems to redirect solar beams reflected by the primary concentrators to the focal point or line. These components allow to increase the concentrated solar flux density and hence to lower thermal radiation losses. Solar reflectors for secondary concentrators are permanently exposed to environmental conditions, high radiation fluxes and elevated temperatures that potentially cause stress and degradation throughout the time. Therefore, analyzing solar reflectors of secondary concentrators by simulating these conditions is crucial. No previous research works about the durability of solar reflector materials for secondary concentrators have been reported. The present work is focused on studying the degradation of the reflector materials by simulating accelerated aging, caused by several ambient parameters and the effect of concentrated radiation. Both cooled and uncooled systems for secondary concentrators are included in this study. According to results obtained, aluminum reflectors and thin silvered-glass reflectors glued to an aluminum structure showed minimum reflectance losses and structural degradation under the operation conditions of cooled 3D secondary concentrators (tower systems). Following critical aspects to avoid reflector degradation were identified: to select a suitable adhesive material to glue the thin silvered-glass reflector to the support aluminum structure, to properly protect reflectors edges, to design a suitable cooling system and to avoid the combination of high radiation fluxes with mechanical stress. In addition, laminated silvered-glass reflectors have shown to be suitable for uncooled 2D secondary concentrators (Fresnel collectors). Furthermore, a comparison with naturally aged secondary concentrators using silvered-glass reflectors glued to an aluminum structure revealed that the simulated degradation under accelerated conditions performed in this work did reproduce the most frequent degradation patterns suffered in real operating conditions.

This article describes an innovative method for measuring lighting levels and other lighting parameters through the use of aerial imagery of towns and cities. Combined with electricity consumption data from smart electricity meters, it was possible to measure the energy efficiency of public lighting installations. The results of this study also confirmed that lighting measurements, installation material, luminaire position, and electricity consumption data can be easily integrated into geographic information systems (GIS). The main advantage of this new methodology is that it provides information about lighting installations in large areas in less time than more conventional procedures. It is thus a more effective way of obtaining the data required to calculate the energy efficiency of lighting levels and electricity consumption. There is even the possibility of generating street lighting maps that provide local administrations with up-to-date information regarding the status of public lighting installations in their city. In this way, modifications or improvements can be made to achieve greater energy savings and, if necessary, to correct the distribution or configuration of public lighting systems to make them more efficient and sustainable. This research studied levels of street lighting and calculated the energy efficiency in various streets of Deifontes (Granada), through the use of aerial imagery.