• Energy Research
• Restricted close
• Embargo close
• 12. Responsible consumption close
• 9. Industry and infrastructure close
• IT close
• ES close

AbstractBACKGROUND: Inappropriate utilisation of biosolids may adversely impact agrosystem productivity. Here, we address the response of wheat (Triticum durum) to different doses (0, 40, 100, 200 and 300 t ha−1) of either municipal solid waste (MSW) compost or sewage sludge in a greenhouse pot experiment. Plant growth, heavy metal uptake, and antioxidant activity were considered.RESULTS: Biomass production of treated plants was significantly enhanced at 40 t ha−1 and 100 t ha−1 of MSW compost (+48% and +78% relative to the control, respectively). At the same doses of sewage sludge, the increase was only 18%. Higher doses of both biosolids restricted significantly the plant growth, in concomitance with the significant accumulation of heavy metals (Ni2+, Pb2+, Cu2+ and Zn2+), especially in leaves. Leaf activities of antioxidant enzymes (ascorbate peroxidase, glutathione reductase, catalase and superoxide dismutase) were unchanged at 40 t ha−1 MSW compost or sewage sludge, but were significantly stimulated at higher doses (200–300 t ha−1), together with higher leaf concentration of reduced glutathione.CONCLUSION: This preliminary study suggests that a MSW supply at moderate doses (100 t ha−1) could be highly beneficial for wheat productivity. Copyright © 2010 Society of Chemical Industry

The world, society and education are constantly evolving, and to respond to these changes, the main governmental institutions have been proposing different global strategies to focus efforts in the same direction. Currently, the United Nations and its 17 Sustainable Development Goals (SDG) have presented a series of indicators that could help to minimise the environmental, economic and social instability we are experiencing. In this sense, Education for Sustainable Development (ESD) has been described as a fundamental factor. Specifically, in previous work, we argued that physical education (PE) could be a good tool to contribute to SDGs. Based on this, no research analysing the voices of Physical Education Teachers (PET) on how this contribution could be made has been identified in previous literature. Therefore, the objectives of this research are: (1) to analyse the voices and opinions of active PETs in terms of the knowledge they have about Sustainable Development (SD); (2) to determine their opinions about the contribution that PE could make to SDGs; and finally, (3) to identify the challenges and limitations of pedagogical action of SD in PE. For this purpose, a qualitative analysis through a semi-structured interview with 41 active PETs was carried out. The main findings will be presented and discussed around four themes: (a) agreement on the concept of sustainability; (b) PE can contribute to the achievement of SDGs; (c) ambiguity in applying SDGs to PE lessons; and (d) teachers’ constraints on how to implement SDGs in PE. It seems to indicate that PETs do not have a multidimensional vision of sustainable development. While they recognise the potential of PE to contribute to SDGs through awareness raising and student learning, they point to its pedagogical and formative constraints as the main barriers to being able to contribute. They pointed to a lack of knowledge on how to do so, guidelines on how to integrate ESD, lack of involvement, shortage of time or resources in school physical education.

Emergency building, devoted to give rapid and effective housing solutions to catastrophic and unexpected events, relies on the basic principles of construction rapidity and reversibility as well as the use of alternative energy sources. The growing need for environmental impact reduction in the building sector represents for temporary housing - especially under emergency conditions - a priority requisite, since, after given time lapses, areas occupied with emergency settlements will have to be recovered to their original use. In this case, the buildings' service life does not correspond to the life cycle of their materials and components; as a consequence, design activities will have to assure the dismantability and reusability of structures for further service cycles, making the whole process reversible: from construction to 'zero waste' de-construction. This paper aims at defining design criteria for low-impact emergency dwellings, assessing at the same time their applicability to corrugated steel pipes, obtained by assembling galvanized curved sheets - commonly used for underpasses and conduits - for which different use possibilities have been investigated. In this view, the research program has led to the definition of modular dwelling solutions. Then, technical feasibility studies have been carried out in collaboration with the industrial sector, taking advantage of consolidated production lines for innovative use purposes. Along the different research stages, a methodology has been defined for the assessment of the fundamental sustainability criteria through different simulation procedures; among these, the evaluation of the life-cycle environmental impacts with SimaPRO software and the 3D modelling for the maximization of the construction/environment integration - also in relation to the use of PV modules - have produced interesting results.

Wood biomass is turned into industrial fuel through chipping. The efficiency of chipping depends on many factors, including chipper knife wear. Chipper knife wear was determined through a long-term follow-up study, conducted at a waste wood recycling yard. Knife wear determined a sharp drop of productivity (>20%) and a severe decay in product quality. Dry sharpening with a grinder mitigated this effect, but it could not replace proper wet sharpening. Increasing the frequency of wet sharpening sessions determined a moderate increase of knife depreciation cost, but it could drastically enhance machine performance and reduce biomass processing cost. Since benefits largely exceed costs, increasing the frequency of wet sharpening sessions may be an effective measure for reducing overall chipping cost. If the main goal of a chipper operator is to increase productivity and/or decrease fuel consumption, then managing knife wear should be a primary target. (C) 2014 Elsevier Ltd. All rights reserved.

Alternative fuels and energy vectors are becoming increasingly important in terms of technical, geopolitical, economic, and environmental aspects. In particular, gaseous fuels and vectors, such as fossil or synthetic natural gas (NG) blended with hydrogen, commonly help provide optimal strategies to reduce global and toxic emissions of internal combustion engines, owing to their adaptability, anti-knock capacity, lower toxicity of pollutants, reduced CO2 emissions, and costeffectiveness. However, diesel engines still represent the reference category among internal combustion engines in terms of maximum thermodynamic efficiency. The possibility offered by dual-fuel (DF) systems to combine the efficiency and performance of diesel engines with the environmental advantages of gaseous fuels has been the subject of extensive investigations. However, the simple replacement of diesel fuel with gaseous fuel does not allow for optimising the engine performance, owing to the high percentage of unburned gaseous fuel, which compromises the potential reduction of CO2; therefore, more complex combustion strategies should be realised. In this study, with the aim of improving the DF combustion process, an experimental investigation was performed to analyse low-temperature combustion (LTC), using NG and two enriched hydrogen-compressed NG blends as primary fuels. The LTC mode was activated by means of a very early advanced pilot injection and carried out in two close steps. The double pilot injection was used to control the energy release rate in the first combustion stage, thereby minimizing the increase of the rate of pressure and allowing the extension of the operation range under LTC. The experimental activity was also focused on analysing the particle emissions, as it is well known that these emissions, together with those of nitrogen oxide, constitute the main pollutants resulting from diesel fuel combustion. The results demonstrated the potential to reduce the unburned fuel, NOx, and particle emissions simultaneously, while maintaining equivalent CO2 emissions to a diesel-only engine. Both the timing and pressure of the pilot injection proved to be critical parameters for optimising the emissions and performance

Landfill gas (LFG) tends to escape from the landfill surface even when LFG collecting systems are installed. Since LFG leaks are generally a noticeable percentage of the total production of LFG, the optimisation of the collection system is a fundamental step for both energy recovery and environmental impact mitigation. In this work, we suggest to take into account the results of direct measurements of gas fluxes at the air-cover interface to achieve this goal.During the last 5 years (2004-2009), 11 soil gas emission surveys have been carried out at the Municipal Solid Waste landfill of Legoli (Peccioli municipality, Pisa Province, Italy) by means of the accumulation chamber method. Direct and simultaneous measurements of CH(4) and CO(2) fluxes from the landfill cover (about 140,000 m(2)) have been performed to estimate the total output of both gases discharged into the atmosphere. Three different data processing have been applied and compared: Arithmetic mean of raw data (AMRD), sequential Gaussian conditional simulations (SGCS) and turning bands conditional simulations (TBCS). The total amount of LFG (captured and not captured) obtained from processing of direct measurements has been compared with the corresponding outcomes of three different numerical models (LandGEM, IPCC waste model and GasSim).Measured fluxes vary from undetectable values (<0.05 mol m(-2) day(-1) for CH(4) and <0.02 mol m(-2) day(-1) for CO(2)) to 246 mol m(-2) day(-1) for CH(4) and 275 mol m(-2) day(-1) for CO(2). The specific CH(4) and CO(2) fluxes (flux per surface unit) vary from 1.8 to 7.9 mol m(-2) day(-1) and from 2.4 to 7.8 mol m(-2) day(-1), respectively.The three different estimation methodologies (AMRD, SGCS and TBCS) used to evaluate the total output of diffused CO(2) and CH(4) fluxes from soil provide similar estimations, whereas there are some mismatches between these results and those of numerical LFG production models. Isoflux maps show a non-uniform spatial distribution, with high-flux zones not always corresponding with high-temperature areas shown by thermographic images.The average value estimated over the 5-year period for the Legoli landfill is 245 mol min(-1) for CH(4) and 379 mol min(-1) for CO(2), whereas the volume percentage of CH(4) in the total gas discharged into the atmosphere varies from 29% to 51%, with a mean value of 39%. The estimated yearly emissions from the landfill cover is about 1.29 x 10(8) mol annum(-1) (2,100 t year(-1)) of CH(4) and 1.99 x 10(8) mol annum(-1) (8,800 t year(-1)) of CO(2). Considering that the CH(4) global warming potential is 63 times greater than that of CO(2) (20 a time horizon, Lashof and Ahuja 1990), the emission of methane corresponds to 130,000 t annum(-1) of CO(2).The importance of these studies is to provide data for the worldwide inventory of CH(4) and CO(2) emissions from landfills, with the ultimate aim of determining the contribution of waste disposal to global warming. This kind of studies could be extended to other gas species, like the volatile organic compounds.

The transition to a low carbon future is starting to affect landscapes around the world. In order for this landscape transformation to be sustainable, renewable energy technologies should not cause critical trade-offs between the provision of energy and that of other ecosystem services such as food production. This literature review advances the body of knowledge on sustainable energy transition with special focus on ecosystem services-based approaches and methods. Two key issues emerge from this review: only one sixth of the published applications on the relation between renewable energy and landscape make use of the ecosystem service framework. Secondly, the applications that do address ecosystem services for landscape planning and design lack efficient methods and spatial reference systems that accommodate both cultural and regulating ecosystem services. Future research efforts should be directed to further advancing the spatial reference systems, the use of participatory mapping and landscape visualizations tools for cultural ecosystem services and the elaboration of landscape design principles.

Abstract In recent years, the overall energy consumption is increasing significantly and the energy consumption in the building sector represents over 30% of the global ones in developed countries. Thermal energy storage (TES) using phase change materials (PCM), which are materials able to store high amounts of energy as latent heat, is suggested as a possible solution to decrease the energy consumption. The authors of this paper developed materials able to encapsulate/stabilize PCM in addition to isolate an industrial residue from the steel recycling process: electrical arc furnace dust (EAFD). This waste is a hazardous dust, and when it is combined with a polymeric matrix produce dense sheet materials suitable for multilayered constructive systems. In this paper the physical, mechanical, thermal and acoustical characterization of two new materials with EAFD and PCM in a polymeric matrix for constructive system is presented. The results are compared with those obtained for one commercial dense sheet material available in the market, Texsound commercialized by TEXSA (Spain). The new dense sheet materials developed in this paper have similar acoustic properties compared to the results obtained for the commercial material and are competitive with it, even better because the new material incorporates PCM which increases the thermal inertia of final constructive system.