• Energy Research
• other engineering and technologies close
• 7. Clean energy close
• 12. Responsible consumption close
• AU close
• EU close

Microalgae have tremendous potential for producing liquid renewable fuel. Many methods for converting microalgae to biofuel have been proposed; however, an economical and energetically feasible route for algal fuel production is yet to be found. This paper presents a review on the comparison of the most promising conversion pathways of microalgae to liquid fuel: hydrothermal liquefaction (HTL), wet extraction and non-destructive extraction. The comparison is based on important assessment parameters of product quality and yield, nutrient recovery, GHG emissions, energy and the cost associated with the production of fuel from microalgae, in order to better understand the pros and cons of each method. It was found that the HTL pathway produces more oil than the wet extraction pathway; however, higher concentrations of unwanted components are present in the HTL oil produced. Less nutrients (N and P) can be recovered in HTL compared to wet extraction. HTL consumes more fossil energy and generates higher GHG emissions than wet extraction, while the production cost of fuel from HTL pathway is lower than wet extraction pathway. There is considerable uncertainty in the comparison of the energy consumption and economics of the HTL pathway and the wet extraction pathway due to different scenarios analysed in the assessment studies. To be able to appropriately compare methodologies, the conversion methods should be analysed from growth to upgradation of oil utilising sufficiently similar assumptions and scenarios. Based on the data in available literature, wet oil extraction is the more appropriate system for biofuel production than HTL. However, the potential of alternative extraction/conversion technologies, such as, non-destructive extraction, need to be further assessed.

Short-term load forecasting is an essential instrument in power system planning, operation and control. Many operating decisions are based on load forecasts, such as dispatch scheduling of generating capacity, reliability analysis, and maintenance planning for the generators. Overestimation of electricity demand will cause a conservative operation, which leads to the start-up of too many units or excessive energy purchase, thereby supplying an unnecessary level of reserve. On the contrary, underestimation may result in a risky operation, with insufficient preparation of spinning reserve, causing the system to operate in a vulnerable region to the disturbance. In this paper, semi-parametric additive models are proposed to estimate the relationships between demand and the driver variables. Specifically, the inputs for these models are calendar variables, lagged actual demand observations and historical and forecast temperature traces for one or more sites in the target power system. In addition to point forecasts, prediction intervals are also estimated using a modified bootstrap method suitable for the complex seasonality seen in electricity demand data. The proposed methodology has been used to forecast the half-hourly electricity demand for up to seven days ahead for power systems in the Australian National Electricity Market. The performance of the methodology is validated via out-of-sample experiments with real data from the power system, as well as through on-site implementation by the system operator.

Abstract With promising benefits such as traffic emission reduction, traffic congestion alleviation, and parking problem solving, Electric Vehicle (EV)-sharing systems have attracted large attentions in recent years. Different from other business modes, customers in sharing economy systems are usually price sensitive. Therefore, it is possible to shift the usage of shared EVs through a well-designed Dynamic Pricing Scheme (DPS), with the objective of maximizing the system operator's total profit. In this study, we propose a novel DPS for a large-scale EV-sharing network to address the EV unbalancing issue and satisfy the vehicle-grid-integration (VGI) service based on accurate station-level demand prediction. The proposed DPS is formulated as a complex optimization problem, which includes two Price Adjustment Level (PAL) decision variables for every origin-destination pair of stations. The two PALs are employed to affect the EV-sharing demand and travel time between each station pair, respectively. Physical and operational constraints from both EV demand and VGI service aspects are also included in the proposed model. Two case study are conducted to validate the effectiveness of the proposed method.

The energy considered as waste heat in industrial furnaces owing to inefficiencies represents a substantial opportunity for recovery by means of thermal energy storage (TES) implementation. Although conventional systems based on sensible heat are used extensively, these systems involve technical limitations. Latent heat storage based on phase change materials (PCMs) results in a promising alternative for storing and recovering waste heat. Within this scope, the proposed PCM-TES allows for demonstrating its implementation feasibility in energy-intensive industries at high temperature range. The stored energy is meant to preheat the air temperature entering the furnace by using a PCM whose melting point is 885 °C. In this sense, a heat transfer model simulation is established to determine an appropriate design based on mass and energy conservation equations. The thermal performance is analysed for the melting and solidification processes, the phase transition and its influence on heat transference. Moreover, the temperature profile is illustrated for the PCM and combustion air stream. The obtained results prove the achievability of very high temperature levels (from 700 to 865 °C) in the combustion air preheating in a ceramic furnace; so corroborating an energy and environmental efficiency enhancement, compared to the initial condition presenting an air outlet at 650 °C.

Abstract This paper aims to present a feasibility study of the innovative plant for methanol synthesis from carbon dioxide-sequestered by fossil fuel power plant and hydrogen, which is produced by water electrolyzer employing the over-production on the electrical grid. The thermo-economic analysis is performed in the framework of the MefCO2 H2020 EU project and it is referred to the German economic scenario, properly taking into account the real market costs and cost functions for different components of the plant. Three different plant capacities for methanol production (4000 10,000 and 50,000 ton/year) have been investigated, assuming an average cost for electrical energy to feed electrolysers and analyzing the influence of the most significant parameters (oxygen selling option, methanol selling price and electrolysers’ capital cost) on the profitability of the plant. The analysis has been performed in W-ECoMP, software for the thermo-economic analysis and plant optimization developed by the University of Genoa.

AbstractSmart Grids are electrical grids that require a decentralised way of controlling electric power conditioning and thereby control the production and distribution of energy. Yet, the integration of Distributed Renewable Energy Sources (DRESs) in the Smart Grid introduces new challenges with regards to electrical grid balancing and storing of electrical energy, as well as additional monetary costs. Furthermore, the future smart grid also has to take over the provision of Ancillary Services (ASs). In this paper, a distributed ICT infrastructure to solve such challenges, specifically related to ASs in future Smart Grids, is described. The proposed infrastructure is developed on the basis of the Smart Grid Architecture Model (SGAM) framework, which is defined by the European Commission in Smart Grid Mandate M/490. A testbed that provides a flexible, secure, and low-cost version of this architecture, illustrating the separation of systems and responsibilities, and supporting both emulated DRESs and real hardware has been developed. The resulting system supports the integration of a variety of DRESs with a secure two-way communication channel between the monitoring and controlling components. It assists in the analysis of various inter-operabilities and in the verification of eventual system designs. To validate the system design, the mapping of the proposed architecture to the testbed is presented. Further work will help improve the architecture in two directions; first, by investigating specific-purpose use cases, instantiated using this more generic framework; and second, by investigating the effects a realistic number and variety of connected devices within different grid configurations has on the testbed infrastructure.

Abstract In this paper, we investigate distributed thermal-electrochemical modeling of a Lithium-Ion battery cell to include the effect of temperature distribution across the thickness of the cell as a first step to study the module level temperature distribution at high charging rates. Most recent works have focused on lumped thermal models for a Li-Ion cell which ignore any temperature differential across cell thickness. However, even a small temperature differential across cell thickness at the cell level can contribute to significant temperature differential in the thickness direction of stacked-up Li-Ion cells at the module level. Such temperature differential can potentially impact the battery charging control system, especially at high charging rates. Here, the thermal-electrochemical partial differential and algebraic equations for a Li-ion cell are solved via a spatial finite difference method. Simulation results show that the temperature differentials over the cell thickness at the cell level are not insignificant, particularly at high charging rates.

In recent years, sustainability concerns have gained increasing attention among countries and stakeholders worldwide. Towards the transition to sustainable rural development, the rural web framework (RWF) has become a consistent tool. Indicators from the RWF have been used to explore sustainable rural development for decision-making tasks, which improves the social, economic, and environmental performance of rural regions. However, the application of the RWF in studies is on the decline. Furthermore, there is a lack of literature reviews on the importance of the RWF and its relationship with different facets of sustainable development. We conducted a systematic literature review (SLR) (a) to explore how studies have used the RWF in the context of sustainable development and (b) to identify areas for further research. This study found that the RWF has mostly been used in developed countries, with fewer applications in developing countries. We suggest that there should be increased application of the RWF, particularly in developing countries, to broaden the rural web–sustainable development discourse and its relevance. This paper presents several areas where the indicators of the RWF can be applied to illustrate their relevance for policy decisions towards the achievement of the sustainable development goals (SDGs).