• Energy Research
• Restricted close
• 12. Responsible consumption close
• 6. Clean water close
• 1. No poverty close
• EU close
• CN close

Wood biomass is turned into industrial fuel through chipping. The efficiency of chipping depends on many factors, including chipper knife wear. Chipper knife wear was determined through a long-term follow-up study, conducted at a waste wood recycling yard. Knife wear determined a sharp drop of productivity (>20%) and a severe decay in product quality. Dry sharpening with a grinder mitigated this effect, but it could not replace proper wet sharpening. Increasing the frequency of wet sharpening sessions determined a moderate increase of knife depreciation cost, but it could drastically enhance machine performance and reduce biomass processing cost. Since benefits largely exceed costs, increasing the frequency of wet sharpening sessions may be an effective measure for reducing overall chipping cost. If the main goal of a chipper operator is to increase productivity and/or decrease fuel consumption, then managing knife wear should be a primary target. (C) 2014 Elsevier Ltd. All rights reserved.

It is recognised that several constraints such as the lack of knowledge and expertise of farmers, land users and policy makers concerning agroforestry systems establishment and management hamper the adoption of agroforestry systems (Camilli et al. 2017). AFINET project acts at EU level in order to direct research results into practice and promote innovative ideas to face challenges and solve practitioners' problems. AFINET proposes an innovative methodology based on the creation of a European Interregional Network, linking different Regional Agroforestry Innovation Networks (RAINs). RAINs represent different climatic, geographical, social and cultural conditions and enclose a balanced representation of the key actors with complementary types of expertise (farmers, policy makers, advisory services, extension services, etc.). The Italian RAIN is focused on the Extra-Virgin Olive Oil (EVOO) value chain, with the main aim to promote agroforestry management of local olive orchards. Olive trees are still managed traditionally, often in marginal sites, with minimal mechanization and relatively low external inputs such as chemical treatments in comparison to other crops. The presence of permanent crops (olive trees) guarantees a partially tree cover reducing hydrogeological risk. Soil management usually keeps natural grassing reducing soil carbon emission and increasing soil fertility (Bateni et al. 2017). Intercropping with cereals and/or fodder legumes and livestock can also be practiced in olive orchards, increasing the complexity of the olive tree multifunctional system. Moreover, olive orchards can be managed as agroforestry systems since they can be intercropped with arable crops (cereals, legumes) and/or combined with livestock (sheep, poultry). The RAIN process, involving local stakeholders, highlighted the main bottlenecks of the EVOO value chain related to communication and dissemination of knowledge, technical and management aspects, market and policy. In order to contrast bottlenecks and exploit opportunities of the olive oil supply chain, the identified innovations are: i) adoption of best practices: testing and experimenting innovative agroforestry systems introducing different crop/animals species and varieties; ii) improve the management of the olive orchards: encouraging and increasing the organic production; iii) valorisation of olive processing residues: identifying and testing innovative products (bio-materials, olive paste as example); iv) arise the awareness among consumers: educating people about the benefits of olive oil consumption, creating networks among stakeholders, improving marketing and commercialization. Creating a Bio-district, defined as a geographical area where farmers, citizens, tourist operators, associations and public authorities enter into an agreement for the sustainable management of local resources, emerged a powerful tool to implement the innovation in the local EVOO value chain.

Wet-laying is a mature technology that is applied in large scale for the manufacture of nonwovens, including paper products. However, it usually uses large volumes of water and is energy-intensive. Here we used foam-laying to substantially diminish the volume of water consumed in the formation of fiber networks (5-fold reduction) and to reduce the water content of the nonwovens produced before drying, achieving a reduced energy demand. The prospects of foam-laying were evaluated by comparing foam-laid and wet-laid webs of two types of wood fibers: stiff (lignin-containing) or flexible (lignin-free). Also, the effect of foaming agent type (anionic, cationic, nonionic, and amphoteric) was elucidated. Reference webs were produced by conventional wet-laying, with or without surfactants. Foam-laying was effective in producing a more uniform areal mass distribution (better formation) after wet-pressing. This effect was more evident for the webs synthesized with the flexible fibers. Unlike the layered network structures that were obtained by wet-laying, foam-laid webs exhibited a more felted network, with fibers positioned in the out-of-plane direction. As a result, higher air permeability, web porosity, and light scattering coefficients were measured for the foam-laid webs. The enhanced porosity (lower density) was related to the effect of bubbles during foam-laying and the reduction in surface tension of the foamed-fiber dispersion. The resistance to delamination of low-density webs obtained by foam-laying in the out-of-plane direction was preserved. However, the reduction in tensile strength and modulus of foam-laid webs were determined, owing to the reduced density of the formed structures. Notably, the type of foaming agent used played a minor role as far as the resultant properties of the webs, making the process flexible in terms of the selection of environmentally friendly alternatives. Overall, we compared the physico-mechanical properties of fiber networks formed by web- and foam-laying, depending on fiber type and foaming agent, yielding a property space that is useful in the design of lightweight structures (nonwovens, including paper). The prospects of water and energy savings by foam-laying are the major benefits in the sustainable use of fibers for the assembly of porous materials, such as lightweight nonwoven and paper products.

Available methods for measuring the impact of ocean acidification (OA) and leakage from carbon capture and storage (CCS) on marine sedimentary pH profiles are unsuitable for replicated experimental setups. To overcome this issue, a novel optical sensor application is presented, using off-the-shelf optode technology (MOPP). The application is validated using microprofiling, during a CCS leakage experiment, where the impact and recovery from a high CO2 plume was investigated in two types of natural marine sediment. MOPP offered user-friendliness, speed of data acquisition, robustness to sediment type, and large sediment depth range. This ensemble of characteristics overcomes many of the challenges found with other pH measuring methods, in OA and CCS research. The impact varied greatly between sediment types, depending on baseline pH variability and sediment permeability. Sedimentary pH profile recovery was quick, with profiles close to control conditions 24 h after the cessation of the leak. However, variability of pH within the finer sediment was still apparent 4 days into the recovery phase. Habitat characteristics need therefore to be considered, to truly disentangle high CO2 perturbation impacts on benthic systems. Impacts on natural communities depend not only on the pH gradient caused by perturbation, but also on other processes that outlive the perturbation, adding complexity to recovery.

In this work, a novel enhanced deep borehole heat exchanger (EDBHE) was proposed to improve heat extraction efficiency based on the jet grouting method. By means of this technology, a soilcrete zone with high thermal conductivity was built near the wellbore. To analyze the feasibility and efficiency of this method, we firstly constructed a validated deep borehole heat exchanger (DBHE) model based on the field experimental data. Numerical simulations were carried out to investigate the 30-year production performance of EDBHE. Results demonstrated that the jet grouting method is an efficient way for improving thermal output of DBHE. It is evaluated that the average annual heat production rate over a 30-year heating period of EDBHE is 463.2 kW, which is 1.27 times as that of DBHE. Sensitivity analyses indicate that the heat production rate and outlet temperature mainly depend on the height and radius of the artificial soilcrete zone. However, thermal output is not sensitive to thermal conductivity of the soilcrete zone due to the higher thermal resistance of the geological formation. For the experimental site used in this work, the recommended height, radius, and thermal conductivity of the soilcrete are 1000 m, 1.0 m, and 50 W/m °C, respectively.

Abstract In this study, we investigate the driving forces behind the changes in residential energy consumption (REC) in China’s urban and rural areas over the 2001–2012 period. Based on the logarithmic mean Divisia index method, the REC changes are decomposed into seven driving forces, which are climate change, energy price, energy expenditure mix, energy cost share (in total expenditure), expenditure share (in income), per capita income and population effects. According to the results, climate effect due to increasing days with abnormal temperature, energy cost share effect characterized by more expenditure to be paid for energy use, income effect describing constant income growth in the residential sector definitely increase REC in both urban and rural areas. In contrast, energy prices and energy expenditure mix effects negatively contribute to the REC increase, respectively because of the increase in energy prices and the transition from the low-priced energy to high-priced energy. Expenditure share and population effects play opposite roles in urban and rural areas, and the reasons and implications are analysed in depth.

Decreasing nutrient losses from excessive synthetic fertilizer inputs is the direct and valid way to address low nutrient use efficiency and the related environmental consequences. Here, we established a comprehensive database of nitrogen (N), phosphorus (P), and carbon (C) losses from rice paddy fields in China, which we used to evaluate fertilization-induced losses and the impact of environmental factors, and to mitigate losses by adopting alternative fertilization options and setting input thresholds. Our results showed that most N-loss pathways had exponential increases with additional N input. In average, 23.8% of the N applied was lost via NH3 (16.1%), N2O (0.3%), leaching (4.8%), and runoff (2.6%). Total P loss was approximately 2.7% of the input, composed of leaching (1.3%) and runoff (1.4%). C lost as CH4 accounted for 4.9% of the organic C input. A relative importance analysis indicated that climate or soil variation rather than fertilizer rate was the dominant factor driving N and P leaching, and CH4 emissions. Based on the sensitivity of multiple N-loss pathways to N fertilization, we propose upper thresholds for N inputs of 142–191 kg N ha−1 across four rice types, which would avoid dramatic increases in N losses. Compared to conventional chemical fertilization, alternative fertilization options had diverse performances: enhanced-efficiency N fertilizer reduced N loss rate by 7.8 percent points and the global warming potential (GWP, considering N2O and CH4 emissions) by 28.8%; combined manure and chemical N fertilizer reduced N loss rate by 9.0 percent points but increased the GWP by 56.9%; straw return had no effect on total N loss but almost doubled the GWP. Using nutrient sources most appropriate to site-specific conditions is demonstrated as a robust way to decrease nutrient losses. Setting nutrient input thresholds would also contribute to the mitigation of environmental pollution, especially in regions with poor fertilization recommendation systems.

The effect of substrate changes on the performance and microbial community of two-chamber microbial fuel cells (MFCs) was investigated in this study. The MFCs enriched with a single substrate (e.g., acetate, glucose, or butyrate) had different acclimatization capability to substrate changes. The MFC enriched with glucose showed rapid and higher power generation, when glucose was switched with acetate or butyrate. However, the MFC enriched with acetate needed a longer adaptation time for utilizing glucose. Microbial community was also changed when the substrate was changed. Clostridium and Bacilli of phylum Firmicutes were detected in acetate-enriched MFCs after switching to glucose. By contrast, Firmicutes completely disappeared and Geobacter-like species were specifically enriched in glucose-enriched MFCs after feeding acetate to the reactor. This study further suggests that the type of substrate fed to MFC is a very important parameter for reactor performance and microbial community, and significantly affects power generation in MFCs.