• Energy Research
• other engineering and technologies close
• 13. Climate action close
• 12. Responsible consumption close
• 15. Life on land close
• GB close
• EU close

© 2020 Elsevier Ltd Free cooling of buildings uses the nocturnal outdoor air as a heat sink via a ventilation process. This could be performed by storing the night coolness for use during the daytime as appropriate. Due to the latent heat capacity, phase change material (PCM) could play anessential role in the effective operation of the free cooling systems by shifting the daytime peak load to the night. However, there is a scarceness on the technology application in hot climates. This paper presents results of a parametric investigation into the application of PCMs as thermal energy storage (TES) to provide sustainable cooling to buildings in hot arid climate by making use of the night-time free cooling. The proposed TES medium comprises an arrangement of metallic modules filled with RT28HC PCM. Numerous geometrical configurations and operational parameters have been assessed. A transient CFD simulation has been employed using ANSYS Fluent software. Validation of the numerical results with experimental data has shown a good agreement. The results have demonstrated that the temperature difference between the PCM and the air, at appropriate air flow rate would have a significant impact on the performance of the system. A free cooling system based on the proposed arrangement has the potential to meet around 42% of a typical building cooling load and has the ability to save up to 67% of building cooling energy load in summer season compared to conventional air-conditioning systems in hot arid climates.

The energy considered as waste heat in industrial furnaces owing to inefficiencies represents a substantial opportunity for recovery by means of thermal energy storage (TES) implementation. Although conventional systems based on sensible heat are used extensively, these systems involve technical limitations. Latent heat storage based on phase change materials (PCMs) results in a promising alternative for storing and recovering waste heat. Within this scope, the proposed PCM-TES allows for demonstrating its implementation feasibility in energy-intensive industries at high temperature range. The stored energy is meant to preheat the air temperature entering the furnace by using a PCM whose melting point is 885 °C. In this sense, a heat transfer model simulation is established to determine an appropriate design based on mass and energy conservation equations. The thermal performance is analysed for the melting and solidification processes, the phase transition and its influence on heat transference. Moreover, the temperature profile is illustrated for the PCM and combustion air stream. The obtained results prove the achievability of very high temperature levels (from 700 to 865 °C) in the combustion air preheating in a ceramic furnace; so corroborating an energy and environmental efficiency enhancement, compared to the initial condition presenting an air outlet at 650 °C.

The Severn Estuary has the world's second largest tide range and a barrage across the estuary, located just seawards of Cardiff in Wales and Weston in the South West England, has been proposed for over half a century, with the objective of extracting large amounts of tidal energy. A Severn Barrage, as previously proposed by the Severn Tidal Power Group (STPG), would be the largest renewable energy project for tidal power generation in the world, if built as proposed, and would generate approximately 5% of the UK's electricity needs. However, concerns have been raised over the environmental impacts of such a barrage, including potential increase in flood risk, loss of intertidal habitats etc. In addressing the challenges of maximizing the energy output and minimizing the environmental impacts of such a barrage, this research study has focused on using a Continental Shelf model, based on the modified Environmental Fluid Dynamics Code (EFDC) with a barrage operation module (EFDC_B), to investigate both the far and near field hydrodynamic impacts of a barrage for different operating scenarios. Three scenarios have been considered to simulate the Severn Barrage, operating via two-way generation and using different combinations of turbines and sluices. The first scenario consisted of 216 turbines and 166 sluices installed along the barrage; the second consisted of 382 turbines with no sluices; and the third consisted of 764 turbines and no sluices. The specification of the sluice gates and turbines are the same for all scenarios. The model results indicate that the third scenario has the best mitigating effects for the far-field and near-field flood risks caused by a barrage and produces the most similar results of minimum water depth and maximum velocity distributions to those obtained from simulating the natural conditions of the estuary, i.e. the current conditions. The results also show that the flow patterns around the barrage are closest to those for the existing natural conditions with minimal slight changes in the estuary. Thus, the results clearly indicate that the environmental impacts of a Severn Barrage can be minimized if the barrage is operated for two-way generation and under the third scenario. Although it appears that the energy output for the third scenario is less than that obtained for the other two scenarios, if very low head (VLH) turbines are used, then the third scenario could generate more energy as more turbines could be cited along the barrage structure. Therefore, the study shows that a Severn Barrage, operating in two-way generation and with 764 turbines (ideally VLH turbines), would be the best option to meet the needs of maximizing the energy output, but having a minimal impact on environmental changes in the estuary and far-field.

Biomass plays an important role in the world primary energy supplies, currently providing ∼14% of the world's primary energy needs and being the fourth largest contributor following coal, oil and natural gas. Over the past decade, domestic biomass heating has received more governmental and public supports than ever before in many developed countries, such as the UK. Although biomass combustion releases some combustion pollutants, biomass is renewable and produces little net CO 2 emissions to the atmosphere. Owing to the low sulphur and low nitrogen contents of many biomass materials, substituting biomass for fossil fuels, particularly coal, can reduce SO x and NO x emissions. This study investigated flue gas emissions, particularly carbon monoxide and nitrogen oxides, of a domestic biomass boiler under various operating conditions. The biomass boiler used in this study satisfies the current EU regulation (EN 303-05) on emissions of domestic biomass boilers. Emissions of the boiler had been measured not only under normal combustion conditions, but also under 'idle' combustion conditions when the boiler was not in but was ready for full operation. The experimental results are analysed and presented in this paper. Copyright The Author 2010. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oxfordjournals.org, Oxford University Press.

Abstract This paper aims to present a feasibility study of the innovative plant for methanol synthesis from carbon dioxide-sequestered by fossil fuel power plant and hydrogen, which is produced by water electrolyzer employing the over-production on the electrical grid. The thermo-economic analysis is performed in the framework of the MefCO2 H2020 EU project and it is referred to the German economic scenario, properly taking into account the real market costs and cost functions for different components of the plant. Three different plant capacities for methanol production (4000 10,000 and 50,000 ton/year) have been investigated, assuming an average cost for electrical energy to feed electrolysers and analyzing the influence of the most significant parameters (oxygen selling option, methanol selling price and electrolysers’ capital cost) on the profitability of the plant. The analysis has been performed in W-ECoMP, software for the thermo-economic analysis and plant optimization developed by the University of Genoa.

Abstract A biomass oil/diesel blend was prepared using an emulsion method and combusted in a diesel engine. An injector was then removed and the morphology, composition, and structure of the carbonaceous deposits on the pintle-type nozzle were characterized using a combination of HRTEM, SEM/EDAX, Raman and XRD. Results showed that the carbon deposition of the emulsified fuel with high crystallinity was greater than that of diesel. The agglomerated particulate diameters of the deposited carbon from diesel and emulsified fuel were approximately 10–30 μm and 50 μm, respectively. The carbon deposition mechanism from the emulsified fuel was attributed to the high oxygen content of the groups leading to increased polymerization and subsequent condensation on the nozzle surfaces that was then carbonised.

Sustainability of agro-food supply chains has recently become the subject of greater interest from consumers, firms, governmental organizations and academia as the environment continues to deteriorate. One of the most critical factors influencing the sustainability of an agro-food supply chain is its network design. A particularly challenging aspect in this context is the broad range of influencing indicators associated with the Triple Bottom Line (TBL) of sustainability that need to be considered. However, many of these indicators could not be fully integrated or measured by single-step optimization problems. This paper presents a critical literature review of operational research methods for the design of sustainable supply chains. A novel two-stage hybrid solution methodology is proposed. In the first stage, a partner selection is performed using a hybrid multi criteria decision making based on Analytic Hierarchy Process (AHP) method and the Ordered Weighted Averaging (OWA) aggregation method. The result obtained in the first stage is used in the second stage to develop a multi-objective mathematical model to optimize the design of the supply chain network. This approach allows the simultaneous consideration of all three dimensions of sustainability including carbon footprint, water footprint, number of jobs created and the total cost of the supply chain design. The proposed approach generates a Pareto frontier to aid users in making decisions. Numerical experiments are completed utilizing data from an agro-food company to demonstrate the efficiency and effectiveness of the proposed solution methodology. The analyzes of the numerical results provide important organizational, practical and policy insights on (1) the impact of financial and environmental sustainability on supply chain network design (2) the tradeoff analysis between environmental emission, water footprint, societal implications and associated cost for making informed decision on supply chain investment.

ABSTRACTThe California generation fleet manages the existing variability and uncertainty in the demand for electric power (load). When wind power is added, the dispatchable generators manage the variability and uncertainty of the net load (load minus wind power). The variability and uncertainty of the load and the net load are compared when 8790 MW of wind power are added to the California power system, a level expected when California achieves its 33% renewable portfolio standard, using a data set of 26,296 h of synchronous historic load and modeled historic wind power output. Variability was calculated as the rate of change in power generated by wind farms or consumed by the load from 1 h to the next (MW/h). Uncertainty was calculated as the 1 h ahead forecast error [MW] of the wind power or of the load. The data show that wind power adds no additional variability than is already present in the load variability. However, wind power adds additional uncertainty through increased forecast errors in the net load compared with the load. Forecast errors in the net load increase 18.7% for negative forecast errors (actual less than forecast) and 5.4% for positive forecast errors (actual greater than forecast). The increase in negative forecast errors occurs only during the afternoon hours when negative load forecasts and positive wind forecasts are strongly correlated. Managing the integration of wind power in the California power system should focus on reducing wind power forecast uncertainty for wind ramp ups during the afternoon hours. Copyright © 2013 John Wiley & Sons, Ltd.