• Energy Research
• engineering and technology close
• 12. Responsible consumption close
• 2. Zero hunger close
• CA close
• FR close

Production of biodiesel from yellow grease (waste cooking oil and waste animal fats) is fast emerging as a promising alternative to address the twin challenges before the biodiesel industry today-fluctuation in prices of vegetable oil and the food versus fuel debate. Yellow grease has a high percentage of free fatty acids (FFA) and proves to be an unsuitable feedstock for biodiesel production from commercially viable alkali-catalyzed production systems due to saponification problems.“Green” methodologies based on heterogeneous solid acid catalyzed reactions have the potential to simultaneously promote esterification and transesterification reactions of yellow grease to produce biodiesel without soap formation and offer easy catalyst separation without generation of toxic streams. This paper presents kinetic studies for the conversion of model yellow grease feeds to biodiesel using a heteropolyacid supported on alumina (HSiW/Al2O3) using a batch autoclave. Three model yellow grease feeds were prepared using canola oil with added FFA such as palmitic, oleic and linoleic acid. A pseudo homogeneous kinetic model for the parallel esterification and transesterification was developed. The rate constants and activation parameters for esterification and transesterification reactions for the model yellow grease feeds were determined. The rate constants for esterification are higher than the transesterification rate constants. The kinetic model was validated using the experimental biodiesel data obtained from processing a commercial yellow grease feed. The kinetic model could be used to design novel processes to convert various low-value waste oils, fats and non-food grade oils to sustainable biodiesel. Keywords: Yellow grease, Canola oil, Free fatty acids, Heteropolyacid, Kinetics for esterification and transesterification

Abstract This paper investigates the optimal choice of building energy efficiency (BEE) standard in the context of centralised urban district heating system in northern China. By employing a techno-economic analysis approach, we demonstrate that the current BEE standard implemented in the Chinese cities should be tightened further in order to achieve a socially optimal level. Without considering the externality costs associated with carbon dioxide (CO2) emissions, current BEE standards need to be upgraded to the equivalent level of French RT2005 standard coupled with a properly designed district coal-fired Combined Heat and Power (CHP). In contrast, the equivalent efficiency standard of Swedish building code is preferably to be implemented in the case of explicit carbon emission restriction as long as the marginal cost of carbon emission (carbon price) is sufficiently high. The fuel-switching policy (from coal to natural gas) in the urban district heating system would result in significant increase in overall costs if the BEE upgrade is not taken into account simultaneously. It is also found that BEE improvements in northern Chinese cities are more cost-effective than investing in low-carbon technologies such as wind power or Carbon Capture and storage in the EU and US with regard to CO2 emissions mitigation.

Abstract The hybrid pneumatic power system (HPPS) proposed in this research replaces the battery’s electric-chemical energy with flow work and optimizes the management and utilization of the energy. This power system is able to keep the internal-combustion engine working at its optimal condition and turn its waste energy into effective mechanical energy and so enhance the thermal efficiency of the whole system. Using computer simulation software ITI-SIM, this study simulates the overall dynamic characteristics of the system in accordance with the regulated running-vehicle test-mode ECE47, and, with experimental verification and analysis, proves that this system can meet the requirements of the standard running-car mode. As for recycling the waste energy, the experimental results show that this design could offset the shortcomings of the low-density of pneumatic power and so effectively enhance the efficiency of the whole system.

Abstract Recharging infrastructure (RI) deployment plays a vital role in improving the public recharging availability for transport electrification. Decarbonizing transportation using low-emission electricity requires massive RI network. Even though the consumers are reluctant to purchase electric vehicles (EVs) until RIs are sufficiently placed, the investors are not willing to invest in RIs due to recharging demand uncertainties. Therefore, a scientific planning framework is needed to ensure the sustainable deployment of EV-RIs in complex networks. In this study, a lifecycle thinking-based multi-period infrastructure-planning framework is proposed to develop sustainable public EV-RIs in an urban context. This framework consists of a temporal model to find the dynamic EV-RI demands, a stochastic model to obtain travel distances, and a multi-objective optimization model to select the best desirable capacities and locations for potential EV-RIs. A case study of a typical medium-scale municipality in Canada was assessed using the proposed framework and validated using conventional infrastructure planning scenarios. The geo-processing data, regional travel behaviors, and recharging characteristics were used as model inputs. The results of the case study showed that the proposed framework can be used to estimate multi-period public recharging demands, minimize lifecycle costs, maximize service coverage and infrastructure utilization, and ensure reasonable paybacks compared to conventional planning approaches. Moreover, this framework can be used to compare different investment assistances, which are required in the early stages of the RI deployment process to encourage investors. Furthermore, government and private institutions can use this framework to identify recharging demands, permitting, and developing RIs in the long-run.

Abstract The residential sector accounts for most of energy-consumption in developing countries in the form of traditional energy. The use of commercial energy is nominal and confined mostly to urban areas where fuelwood is already monetized. A model, based on an end-use/process analysis approach, is developed on a spreadsheet, which is capable of simulating scenarios to address issues of increasing traditional energy-demand caused by population growth, sustainable supply capacity of the existing energy resources, potential for development of new and renewable energy resources, technology. This paper is divided into two parts: general energy issues and the modelling approach, and the application of this approach to Nepal in the context of fuelwood-supply sustainability.

The manufacturing industry has undergone numerous revolutions over the years, with a unanimous acceptance of the greater benefits of being sustainable. The present industrial wave—Industry 4.0—by using its enabling technologies and principles holds great potential to develop sustainable manufacturing paradigms which require balancing out the three fundamental elements —products, processes, and systems. Yet, numerous stakeholders, including industrial policy and decision makers, remain oblivious of such potential and requirements. Thus, this bibliometric study is aimed at presenting an overview of the broad field of research on the convergence of sustainable manufacturing and Industry 4.0 under the umbrella of “Sustainable Manufacturing 4.0”, which has yet to be developed. It includes the dissemination of original findings on pathways and practices of Industry 4.0 applied to the development of sustainable manufacturing, contributing a bibliometric structure of the literature on the aforementioned convergence to reveal how Industry 4.0 could be used to shift the manufacturing sector to a more sustainable-based state. An initial research agenda for this emerging area has accordingly been presented, which may pave the way for having a futuristic view on Sustainable Manufacturing 5.0 in the next industrial wave, i.e., Industry 5.0.

Abstract Conversion of carbon contained in the solid residues (tars + biochar) derived from urban biomass gasification named herein TC would allow enhancing the yield of carbon species (CO/CO2) in synthetic gas. For this purpose, three low cost materials have been tested as possible catalysts: iron species (reduced Fe), bone meal (BM), and ashes (ash) recovered from biochar complete oxidation. The parametric study used the following as variables: air GHSV, onset of reaction temperature, reaction time to optimize CO/CO2 molar ratio and tar content in the produced gas. Results showed an autocatalytic effect of biochar leading to the catalytic conversion of approximately 78% of tars by the native metals contained in TC. The catalytic effect was further enhanced by adding Fe, BM, and extra ash. Addition of Fe catalyst resulted in significant heat generation (temperature increase of ca. 500 °C) and a twofold decrease in reaction time to consume all the carbon. Use of ash and BM as catalysts exhibit heat generation comparable to Fe, along with an improved reaction time, complete tars conversion and a CO/CO2 molar ratio to above 1.3 in the produced gas.

The basins of the Indus and Ganges rivers cover 2.20 million km2 and are inhabited by more than a billion people. The region is under extreme pressures of population and poverty, unregulated utilization of the resources and low levels of productivity. The needs are: (1) development policies that are regionally differentiated to ensure resource sustainability and high productivity; (2) immediate development and implementation of policies for sound groundwater management and energy use; (3) improvement of the fragile food security and to broaden its base; and (4) policy changes to address land fragmentation and improved infrastructure. Meeting these needs will help to improve productivity, reduce rural poverty and improve overall human development.

Abstract The need for sustainable zero-carbon fuels to substitute the conventional fossil fuels in the transport field becomes unavoidable to overcome the depletion of petroleum reserves and global warming. Metal fuels are promising energy-carrying materials that can be regenerated through the carbothermal reduction of their oxide combustion products. Their use is economically beneficial and environmental-friendly when oxides are recycled using sustainable energy resources. Among various choices, aluminum/alumina and magnesium/magnesia couples are the best candidates for the combustion/reduction cycles. Thus, the following study reviews the advanced technologies established for the carbothermal reduction of alumina and magnesia using concentrated solar energy to achieve an efficient regeneration of the metal fuels. In conclusion, 68% Al and 96% Mg yields, of highly-pure stable micro-sized powders, were achieved by optimizing the solar reactor design and the reaction operating parameters (pressure, temperature, heating rate, carbon reducing agent, C/oxide content, C/oxide properties, catalysts, bentonite binder). Further investigations are needed to improve the aluminum regeneration by reducing the formation of unwanted Al-oxycarbides by-products.

AbstractThe European Union aspires to reducing the import dependency of raw materials that are critical to its industries. In this respect, mineral resource information and data sharing by European Geological Surveys is crucial. In 2010, the European Commission identified 14 critical non-energy non-agricultural raw materials. This list was updated in 2014. This article presents the Critical Raw Material (CRM) Map of Europe produced by EuroGeoSurvey's Mineral Resources Expert Group. This map shows European mineral deposits from the EU FP7 ProMine project database, as containing critical commodities, according to the list of CRM published by the European Commission.