• Energy Research
• Closed Access close
• Restricted close
• Open Source close
• 7. Clean energy close
• FR close
• NL close

Current energy market designs and pricing schemes fail to give investors the appropriate market signals. In particular, energy prices are not high enough to attract investors to build new or maintain existing power capacity. In this paper we propose a method to compute second-best Pareto optimal equilibrium prices for any market exhibiting non-convexities and, based on this result, an energy market design able to restore the correct energy price signals for supply investors.

Direct Load Control (DLC) is an effective instrument for achieving a guaranteed load curtailment. Unfortunately, if a customer considers that personal discomfort outweighs money savings after DLC shutting down of home appliances, DLC solution can be rejected. This paper proposes the way to remediate customer comfort concerns by pre-storing additional energy in electric loads before their disconnection from the grid. We take electric tank water heaters as an illustrative example of residential loads with storage. To illuminate our approach we first show how to balance electric consumption for pre-storing with user thermal discomfort for a single water heater. Then, we illustrate how the approach can be scaled-up to a multiple-boiler scenario, when ten remotely controlled boilers act next to fifty non-controlled boilers. The simulations for the latter case show that the expected user thermal discomfort can be significantly reduced at the cost of a reasonable increase of electricity demand preceding DLC event.

The unpredictable nature of wind energy makes its integration to the electric grid highly challenging. However, these challenges can be addressed by incorporating storage devices (batteries) in the system. We perform an overall assessment of a single domestic power system with a wind turbine supported by an energy storage device. The aim is to investigate the best operation mode of the storage device such that the occurrence of large power spills can be minimized. For estimating the small probability of large power spills, we use the splitting technique for rare-event simulations. An appropriate Importance Function for splitting is formulated such that it reduces the work-load of the probability estimator as compared to the conventional Crude Monte Carlo probability estimator. Simulation results show that the ramp constraints imposed on the charging/discharging rate of the storage device plays a pivotal role in mitigating large power spills. It is observed that by employing a new charging strategy for the storage device large power spills can be minimized further. There exists a trade-off between reducing the large power spills versus reducing the average power spills.

This paper presents the direct power control (DPC) of asymmetrical six-phase permanent magnet synchronous generator (A6PMSG) which supplied the isolated load via two PWM rectifiers. The study concerns the method of control by the converter (DPC). The proposed method is around two hysteresis controllers that enable the adjustment of active and reactive power. The research in this paper is verified by MATLAB SIMULINK software. It has been demonstrated through the simulation results that the proposed strategy can be an attractive and practical solution to multi-phase machines applications.

Abstract The hybrid pneumatic power system (HPPS) proposed in this research replaces the battery’s electric-chemical energy with flow work and optimizes the management and utilization of the energy. This power system is able to keep the internal-combustion engine working at its optimal condition and turn its waste energy into effective mechanical energy and so enhance the thermal efficiency of the whole system. Using computer simulation software ITI-SIM, this study simulates the overall dynamic characteristics of the system in accordance with the regulated running-vehicle test-mode ECE47, and, with experimental verification and analysis, proves that this system can meet the requirements of the standard running-car mode. As for recycling the waste energy, the experimental results show that this design could offset the shortcomings of the low-density of pneumatic power and so effectively enhance the efficiency of the whole system.

Abstract An alkaline earth boro-aluminosilicate glass (Eagle XG), a soda-lime glass, and a light-weight polyethylene-terephthalate (PET) foil, used as typical substrates for photovoltaics, were treated by an energetic proton beam (3 MeV, dose 106–107 Gy) corresponding to approx. 30 years of operation at low Earth orbit. Properties of the irradiated substrates were characterized by atomic force microscopy, optical absorption, optical diffuse reflectance, Raman spectroscopy, X-ray photoelectron spectroscopy, Fourier-transform infrared (FTIR) spectroscopy, and terahertz (THz) spectroscopy. Minimal changes of optical and morphological properties are detected on the bare Eagle XG glass, whereas the bare PET foil exhibits pronounced increase in optical absorption, generation of photoluminescence, as well as mechanical bending. On the other hand, the identical substrates coated with Indium-tin-oxide (ITO), which is a typical material for transparent electrodes in photovoltaics, exhibit significantly higher resistance to the modifications by protons while ITO structural and electronic properties remain unchanged. The experimental results are discussed considering a potential application of these materials for missions in space.

In this paper, we present the conjugate heat transfer analysis in a 167-kVA dry-type transformer using the parallel version of the computational fluid dynamics code Fluent 6.0. The renormalization group kappa-epsiv model is proposed to compute the turbulent aspect of the convective airflow inside the transformer metal tank for Air Natural/Air Natural cooling conditions. An experimental approach was used to assess Joule losses in the low-/high-voltage windings and eddy-current losses in the magnetic core. The resulting mathematical model was solved using 14 compute nodes on a distributed machine.

The fast decay in PEM fuel cells of a highly active, high performance, but unstable Fe/N/C catalyst like our NC_Ar + NH3 follows a chemical, not an electrochemical, demetallation mechanism for its ORR active FeN4 sites in the catalyst micropores.

PurposeThe purpose of this paper is to outline a comprehensive picture of the coverage of various certification schemes and sustainability principles relating to the entire value‐added chain of biomass and bioenergy and comparing them accordingly.Design/methodology/approachA tri‐dimensional approach (sustainability issues; technical biomass conversion routes; physical trade flows) was developed for testing the coverage of various sustainability dimensions in different phases of the value‐added chain with the chosen certification schemes and sustainability principles.FindingsUsing the tri‐dimensional approach, a comparison of the chosen schemes and principles demonstrated that the application of existing schemes and the development of new ones have placed a major emphasis on the primary production of biomass. Economic and social dimensions related to biofuels and bioenergy processing and trade were either emphasised less or they were covered inadequately. In view of this, the schemes sometimes seem to ignore that the utilisation of renewable energy as such guarantee no positive or neutral climate impact and may not be economically sustainable, especially when bioenergy can often be more expensive than energy generated from fossil energy sources.Originality/valueThe analysis showed that the tri‐dimensional model is an applicable framework that could facilitate policy makers to formulate policies that comprehensively take into consideration the various sustainability dimensions throughout the entire value‐added chain, now and in the future. It can be applied to the future outlining and completion of certification schemes and sustainability principles for biomass and bioenergy, as well as in the testing of their applicability in the implementation.