• Energy Research
• Closed Access close
• Embargo close
• GB close
• DE close
• Applied Energy close

Abstract A variety of novel, recyclable and reusable, construction materials has already been studied within literature during the past years, aiming at improving the overall energy efficiency ranking of the building envelope. However, several studies show that a delicate control of indoor climating elements can lead to a significant performance improvement by exploiting the building’s savings potential via smart adaptive HVAC regulation to exogenous uncertain disturbances (e.g. weather, occupancy). Building Optimization and Control (BOC) systems can be categorized into two different groups: centralized (requiring high data transmission rates at a central node from every corner of the overall system) and decentralized 1 (assuming an intercommunication among neighboring constituent systems). Moreover, both approaches can be further divided into two subcategories, respectively: model-assisted (usually introducing modeling oversimplifications) and model-free (typically presenting poor stability and very slow convergence rates). This paper presents the application of a novel, decentralized, agent-based , model-free BOC methodology (abbreviated as L4GPCAO) to a modern non-residential building (E.ON. Energy Research Center’s main building), equipped with controllable HVAC systems and renewable energy sources by utilizing the existing Building Management System (BES). The building testbed is located inside the RWTH Aachen University campus in Aachen, Germany. A combined rule criterion composed of the non-renewable energy consumption (NREC) and the thermal comfort index – aligned to international comfort standards – was adopted in all cases presented herein. Besides the limited availability of the specified building testbed, real-life experiments demonstrated operational effectiveness of the proposed approach in BOC applications with complex, emerging dynamics arising from the building’s occupancy and thermal characteristics. L4GPCAO outperformed the control strategy that was designed by the planers and system provider, in a conventional manner, requiring no more than five test days.

Abstract In a trial, 10 cucumber plants ( Cucumis sativus , variety ‘Virgo’ F 1 hybrids) were exposed continuously to a concentration of negative air ions exceeding 50 000/c.c. for a period of 40 days. The yield and productivity of the treated plants were compared with those of a control group of 10 plants in a matched-pairs experiment. An Index of Initial Vigour was developed to allow the subsequent production of the previously nursery-grown young plants to be related to their condition at the beginning of the trial. No effect on the total production or productivity at the end of the 40-day period was discerned, but the interim results (e.g. for the 10th day) are consistent with a model of reaction to stress governed by a negative-feedback mechanism. No harmful effects of the use of negatively ionised air were detected.

Abstract The almost two-dimensional steady-state rates of heat loss from arrays of uniformly-spaced vertical rectangular fins, extending upwards—in otherwise stagnant air—from horizontal heated bases, have been measured. (The vertical air gaps between the fins were closed at their sides, by insulated vertical end-barriers.) The effects of various combinations of height, thickness and spacing of the fins, for different base temperatures (in the range 40 to 100°C), have been studied. For the configuration considered, in a normal ambient environment (∼ 20°C), there is an optimal fin spacing (⋍ 16 mm) corresponding to the greatest steady-state rate of free convective/conductive heat loss through the air from the finned system, and this is almost independent of the temperature of the heat exchanger base (in the range 40–100°C). At this optimal spacing for base temperatures not greater than 50°C, the convective/conductive heat transfer rate from the array increases with the fin height up to about 60 mm, so that it would be uneconomic to employ taller fins if convection/conduction is dominant compared with radiation. If the radiation contribution is also considered, then the optimal spacing corresponding to the maximum total steady-state rate of heat loss through the air is somewhat less than the optimal spacing for which, under the same temperature conditions, the maximum steady-state rate of convective/conductive heat leak occurs. The greater the emissivity of the heat exchanger surfaces, the narrower the optimal uniform gaps between the fins. A two-dimensional finite-difference computer program has been composed to predict the temperature distribution throughout the heat exchanger for a stipulated ambient environmental temperature and experimentally-determined distribution of the heat transfer coefficient over the surfaces of the exchanger. This enables, for instance, any hot spots to be located prior to a proposed design being built.

Abstract With hydrogen becoming more and more important as energy carrier, there is a need for high capacity storage technologies preferably operating at low pressures. Chemical storage in metal hydrides is promising for that purpose, but they require thermal management for hydrogen release and storage, respectively. To overcome this challenge, it is beneficial to store the heat needed for hydrogen release during hydrogen storage in the storage system keeping the additional effort to provide that heat low. In this work, the experimental proof of concept of an adiabatic storage reactor is presented. Magnesium hydride and magnesium hydroxide have been used for hydrogen storage and thermochemical heat storage, respectively. A prototype reactor has been developed and experimentally investigated. It was found that the operating temperature of the materials can be adjusted with the gas pressure in a way to establish a temperature gradient from the MgH2 to the Mg(OH)2 and vice versa. Hydrogen storage and release is enhanced by the thermochemical heating/cooling. A pressure of 9 bar is sufficient to store hydrogen with a capacity of 20.8 gH2 L-1 based on the two materials only, without the steel vessel or insulation. In the heat storage compartment, 300 °C have been reached at 9.75 bar during heat release which is high enough to drive the MgH2 dehydrogenation.

This paper describes the nexus of energy justice, supply and security. It advances the case that energy justice is the relatively new concept in this triangle of issues and an area requiring research. There are three central tenets of energy justice: distributional, procedural and recognition justice. Each of these tenets figures at certain stages in the energy supply chain and as a consequence there is an effect on energy supply. An example of the wind energy sector in Denmark is presented which demonstrates how the application and promotion of energy justice can enable the growth of an industry supply chain. This in turn contributes to increased energy security and national economic growth.

Abstract An experimental investigation of the steady-state rates of heat transfer from an array of vertical rectangular fins of 3 mm thickness and 250 mm length, protruding 60 mm perpendicularly upwards from a 250 mm × 190 mm horizontal rectangular base, is reported. For constant (to ±0·1°C) base temperatures between 40°C and 80°C, in an ambient environment of 20±0·2°C, the optimal separation of the parallel fins, corresponding to the maximum rate of heat loss, is 10·5±1·0 mm. The effects of the extent of the fin protrusions on the thermal performances of such vertical fins, on the same base, which was arranged to be either vertical or horizontal , have been studied. The experiments were performed with three different fin protrusions, namely 32 mm, 60 mm and 90 mm, for a base temperature of 40°C above that of the ambient environment. The steady-state rate of heat dissipation from the fin array increased slightly less than linearly with the fin protrusion for both orientations, but the relationship became closer to linear as the fin spacing was increased. A comparison of the abilities to dissipate heat to the room air from the same geometrical configuration having a rectangular fin array but positioned with vertical fins on a vertical base, vertical fins protruding upwards from a horizontal base, or horizontal fins on a vertical base, has been made. The orientation with vertical fins protruding upwards from the horizontal base, is the preferred option because of the relatively high rates of heat transfer that can then be achieved.

The purpose of this paper is to provide a broad overview of the social and environmental costs and benefits of biofuels in Asia. The major factors that will determine the impacts of biofuels are: (1) their contribution to land-use change, (2) the feedstocks used, and (3) issues of technology and scale. Biofuels offer economic benefits, and in the right circumstances can reduce emissions and make a small contribution to energy security. Feedstocks that involve the conversion of agricultural land will affect food security and cause indirect land-use change, while those that replace forests, wetlands or natural grasslands will increase emissions and damage biodiversity. Biofuels from cellulose, algae or waste will avoid some of these problems, but come with their own set of uncertainties and risks. In order to ensure net societal benefits of biofuel production, governments, researchers, and companies will need to work together to carry out comprehensive assessments, map suitable and unsuitable areas, and define and apply standards relevant to the different circumstances of each country. The greatest benefits may come from feedstocks produced on a modest scale as co-products of smart technologies developed for phytoremediation, waste disposal and emissions reduction.

Abstract A coalfield, in excess of 120×10 6 tonnes of coal in situ , has been discovered at Al-Kamil in south-eastern Oman. The coal is classified as highly-volatile bituminous type-A, with an average calorific value of 27.5 GJ per tonne. Unfortunately, it has on average ∼5% by weight sulphur content and an ash content of ∼14% by weight: so it is probably better suited for use as a fuel for electricity generation. However, such coal-fired generation, at present, would incur a higher cost than using indigenous natural gas, but would nevertheless provide an opportunity for diversification away from the existing over-dependence on natural gas and crude oil.