• Energy Research
• engineering and technology close
• 7. Clean energy close
• 13. Climate action close
• 9. Industry and infrastructure close
• US close
• GB close

The Intergovernmental Panel on Climate Change (IPCC) report that to limit warming to 1.5 °C, Bioenergy with Carbon Capture and Storage (BECCS) is required. Integrated assessment models (IAMS) predict that a land area between the size of Argentina and Australia is required for bioenergy crops, a 3–7 time increase in the current bioenergy planting area globally. The authors pose the question of whether vertical farming (VF) technology can enable BECCS deployment, either via land sparing or supply. VF involves indoor controlled environment cultivation, and can increase productivity per unit land area by 5–10 times. VF is predominantly being used to grow small, high value leafy greens with rapid growth cycles. Capital expenditure, operational expenditure, and sustainability are challenges in current VF industries, and will affect the ability to utilise this technology for other crops. The authors argue that, whilst challenging, VF could help reach wider climate goals. Application of VF for bioenergy crops could be a game changer in delivering BECCS technologies and may reduce the land footprint required as well as the subsequent associated negative environmental impacts. VF bioenergy could allow us to cultivate the future demand for bioenergy for BECCS on the same, or less, land area than is currently used globally.

The path congestion and communication risks of electric power communication network have emerged as the carried businesses are becoming more and more heavy. In this paper, a multi-objective optimization method for power communication network routing considering the importance of the carried businesses is proposed to reduce load imbalance and transmission risk. Firstly, information entropy is introduced as the objective of communication network load balancing optimization. And a risk assessment model for power communication network nodes and links is established. Then fuzzy membership functions are adopted to singularize the two objectives to jointly optimize path congestion and communication risks. The device nodes are dynamically divided according to the carried businesses to pursue the global optimization of the power communication network in which the Yen's algorithm is adopted. Finally, this paper uses the IEEE 30-bus communication network to carry out case simulations and analyzes the proposed method to verify the effectiveness and feasibility.

In this paper, we study the interactions among interconnected autonomous microgrids, and propose a joint energy trading and scheduling strategy. Each interconnected microgrid not only schedules its local power supply and demand, but also trades energy with other microgrids in a distribution network. Specifically, microgrids with excessive renewable generations can trade with other microgrids in deficit of power supplies for mutual benefits. Since interconnected microgrids operate autonomously, they aim to optimize their own performance and expect to gain benefits through energy trading. We design an incentive mechanism using Nash bargaining theory to encourage proactive energy trading and fair benefit sharing. We solve the bargaining problem by decomposing it into two sequential problems on social cost minimization and trading benefit sharing, respectively. For practical implementation, we propose a decentralized solution method with minimum information exchange overhead. Numerical studies based on realistic data demonstrate that the total cost of the interconnected-microgrids operation can be reduced by up to 13.2% through energy trading, and an individual participating microgrid can achieve up to 29.4% reduction in its cost through energy trading. To appear in IEEE Transactions on Smart Grid

Wind characteristics (e.g., mean wind speed, gust factor, turbulence intensity and integral scale, etc.) are quite scattered in different measurement conditions, especially during typhoon and/or hurricane processes, which results in the structural engineer ambiguously determining the wind parameters in wind-resistant design of buildings and structures in cyclone-prone regions. In tropical cyclones (including typhoons and hurricanes), the inconsistent wind characteristics may be in part ascribed to the complex flow structure with the coexistence of both mechanical and convective turbulence in the boundary layer of tropical cyclones. Another significant contribution to the scattered wind characteristics is due to various measurement conditions (e.g., terrain exposure and height) and data processing schemes (e.g., averaging time). The removal of the inconsistency in the field-measurement system may offer a more rational comparison of measured wind data from various observation platforms, and hence facilitates a better identification scheme of the wind characteristics to guide the urban planning design and wind-resistant design of buildings and structures. In this study, an analytical framework was firstly proposed to eliminate the potential observation-related effects in wind characteristics and then the wind characteristics of seven field measured tropical cyclones (four typhoons and three hurricanes) were comparatively investigated. Specifically, field measurements of wind characteristics were converted to a standard reference station with a roughness length of 0.03 m, observation duration of 10 min for mean wind and averaging time of 3 s for gusty wind at a 10 m height. The differences of the measured wind characteristics between the typhoons and hurricanes were highlighted. The standardized turbulent wind characteristics under the analytical framework for typhoons and hurricanes were compared with the corresponding recommendations in standard of American Society of Civil Engineers (ASCE 7-10) and Architectural Institute of Japan Recommendations for Loads on Buildings (AIJ-RLB-2004).

A method is presented for calculating the electromagnetic forces on the end windings of turbine generators for both the steady state and transient modes of operation. Part 1 of this paper deals with the basic concepts of the force calculation and gives several examples of steady state forces and how they vary with load and power factor. PartII deals with several types of transient operation. The currents and fields which these transients produce are discussed and forces are found for various cases such as short circuits, synchronizing out of phase and transmission line switching.

A new version of the ENERGY-10 computer program simulates the performance of photovoltaic systems, in addition to a wide range of opportunities to improve energy efficiency in buildings. This paper describes two test cases in which the beta release of ENERGY-10 version 1.4 was used to evaluate energy efficiency and building-integrated photovoltaics (BIPV) for two Federal building projects: a 16,000-ft2 (1,487 m2) office and laboratory building at the Smithsonian Astrophysical Laboratory in Hilo, Hawaii, and housing for visiting scientists [three 1400-ft2 (130 m2) and three 1564-ft2 (145 m2) houses] at the Smithsonian Environmental Research Center in Edgewater, Maryland. The paper describes the capabilities of the software, the method in which ENERGY-10 was used to assist in the design, and a synopsis of the results. The results indicate that ENERGY-10 is an effective tool for evaluating BIPV options very early in the building design process. By simulating both the building electrical load and simultaneous PV performance for each hour of the year, the ENERGY-10 program facilitates a highly accurate, integrated analysis.

The most severe failures in power grids are often characterized as cascading failures where an initial event triggers consequent failures all along the grid often leading to blackouts. Upon identifying a failure and its cascade potential, timely control actions should be performed by the grid operators to mitigate the effect of the cascade. These actions have to be delivered to one or more control devices, creating a dependency between the power grid and its control network. This paper examines the dependency of the operation of the power grid on the control network. Different from literature studies on failure control, our dependency model captures the impact of networking parameters. We formulate an algorithmic model that describes the impact of this dependency on cascade control. Based on this model, we propose an efficient cascade control algorithm using load shedding with consideration of delays in the communication network for power grids. Finally, we evaluate the impact of the power-communication network dependency with uncontrolled grids, ideal/simple control grids and our proposed control scheme. The results demonstrate that the proposed algorithm can significantly reduce the failure of power lines while sustaining larger power demand for users.

AbstractMembrane Technology and Research, Inc. has proposed a hybrid system combining amine scrubbing with membrane technology to reduce energy cost. Previous studies of CO2 absorption mainly focused on coal-fired flue gas with 12% CO2. However, in the hybrid process, the CO2 in the flue gas can be enriched to 20%. Natural gas turbines will have flue gas with as little as 3% CO2。 Based on the arrangement, the hybrid amine/membrane system provides a gas to the system that has double the CO2 concentration of normal flue gas, reduces the volume of gas sent to the capture unit, or reduces the removal requirements for the capture unit.The objective of this work is to minimize the total energy use of stripping concentrated piperazine (PZ) at rich loading when treating flue gas from 3 to 20% inlet CO2. The base-case stripping configuration is the advanced flash stripper with warm rich bypass and cold rich exchanger bypass. . This configuration includes two split cross-exchangers in series, a convective steam heater, a smaller stripper column, a low residence time flash tank, and stripping at high temperature to produce CO2 at 5 to 17bar. Rich loading in 5 and 8m PZ was varied from 0.37 to 0.43mol CO2/mol N. For each rich loading, lean loading was optimized to minimize the total equivalent work. The “Independence” model for PZ in Aspen Plus® was used to simulate the stripping performance.Because 5m PZ has a lower viscosity than 8m PZ, it can achieve a reduced approach temperature in the cross exchanger. The total energy performance for 5m PZ is practically the same as 8m PZ, even though the capacity of 5m PZ is lower. Significantly more energy is required to regenerate solvents with lower rich loading. As CO2 rich loading increases, the equivalent work requirement decreases for the same loading difference between rich and lean.Stripping data for 24 cases, including heat duty, equivalent work, CO2 output pressure, and optimal cold and warm rich bypass were used to build a correlation with CO2 rich and lean loading. The Second Law efficiency based on the ratio of stripping minimum work and total ideal work was introduced to make the most of stripping work. The Second Law efficiency has a maximum value at a specific CO2 loading.

Abstract Transient thermal behaviors of ultra-supercritical steam turbine control valves during the cold start warm-up process of steam turbine systems were comprehensively studied using conjugate heat transfer (CHT) simulation. The geometrical configurations and boundary conditions used in simulation were identical to the field setup in a thermal power plant. The simulated temperature variations were first validated using measurements by the flush-mounted thermocouples inside the solid valve bodies. The CHT simulation implementing the shear stress transport (SST) turbulence model demonstrated good agreement with the field data, and the overall numerical errors were below 10%; however, the numerical errors of the simulation, which used empirical heat transfer coefficients at the fluid–solid interfaces, reached 40%. The determined temperature differences between the cold valve bodies with the hot steam flow decreased significantly. Specifically, the temperature differences along the inner wall surfaces of the valve bodies decreased to less than 50 °C. Further investigation of the transient heat flux distributions and Nusselt number distributions confirmed that the unsteady flow behaviors, such as the alternating oscillations of the annular wall-attached jet, the central reverse flow and the intermediate shear layer instabilities, enhanced the fluid–solid heat convection process and thus contributed to the warming up of the solid valve bodies.

Dans des scénarios réalistes, la performance dynamique d'un cluster de micro-réseaux est largement affectée par la puissance intermittente des sources d'énergie renouvelables et les changements de charge fréquents. Pour résoudre ce problème, un contrôleur secondaire à double couche basé sur le temps fixe distribué est conçu pour améliorer les performances dynamiques inter-microgrid et intra-microgrid dans un temps de stabilisation fixe. Le contrôleur proposé est indépendant des valeurs de fonctionnement initiales par opposition à la loi de contrôle à temps fini. Chaque agent global dans un micro-réseau fonctionne pour atténuer le décalage de charge entre les autres agents globaux, tandis que chaque agent local dans un micro-réseau fonctionne pour réaliser un partage de courant de charge proportionnel et une régulation de tension moyenne entre eux dans un temps fixe. Cependant, comme l'atténuation de la non-concordance de chargement dans des conditions de charge légère affecte l'efficacité du système en raison de pertes de ligne importantes, le fonctionnement du cluster passe à une approche de minimisation des pertes distribuées, qui fonctionne en utilisant des mesures en ligne des micro-réseaux voisins. Pour caractériser le mode de fonctionnement dans la cyber-couche globale, un seuil de point de chargement critique pour le cluster est ainsi déterminé. La performance du cluster utilisant la stratégie proposée est simulée dans l'environnement MATLAB/SIMULINK pour divers scénarios afin de démontrer sa fiabilité et son efficacité. En escenarios realistas, el rendimiento dinámico de un grupo de microrredes se ve afectado en gran medida por la potencia intermitente de las fuentes de energía renovables y los frecuentes cambios de carga. Para abordar este problema, un controlador secundario de doble capa basado en tiempo fijo distribuido está diseñado para mejorar el rendimiento dinámico entre microrredes y entre microrredes dentro de un tiempo de asentamiento fijo. El controlador propuesto es independiente de los valores operativos iniciales en oposición a la ley de control de tiempo finito. Cada agente global en una microrred opera para mitigar el desajuste de carga entre otros agentes globales, mientras que cada agente local en una microrred opera para lograr un reparto de corriente de carga proporcional y una regulación de voltaje promedio entre ellos en un tiempo fijo. Sin embargo, como la mitigación de la falta de coincidencia de carga durante condiciones de carga ligera afecta la eficiencia del sistema debido a pérdidas de línea significativas, la operación del clúster cambia a un enfoque de minimización de pérdidas distribuidas, que opera utilizando mediciones en línea de las microrredes vecinas. Para caracterizar el modo de operación en la capa cibernética global, se determina así un punto crítico de umbral de carga para el clúster. El rendimiento del clúster que emplea la estrategia propuesta se simula en el entorno MATLAB/SIMULINK para varios escenarios para demostrar su confiabilidad y eficiencia. In realistic scenarios, the dynamic performance of a microgrid cluster is largely affected by the intermittent power of renewable energy sources and frequent load changes. To address this issue, a distributed fixed-time based dual layer secondary controller is designed to improve inter-microgrid and intra-microgrid dynamic performance within a fixed settling time. The proposed controller is independent of initial operating values as opposed to the finite time control law. Each global agent in a microgrid operates to mitigate loading mismatch between other global agents, whereas each local agent in a microgrid operates to achieve proportionate load current sharing and average voltage regulation between them in fixed time. However, as loading mismatch mitigation during light load conditions affects the system efficiency due to significant line losses, the cluster operation switches to a distributed loss minimization approach, which operates using online measurements from the neighboring microgrids. To characterize the mode of operation in the global cyber layer, a critical point of loading threshold for the cluster is thus determined. The performance of the cluster employing the proposed strategy is simulated in MATLAB/SIMULINK environment for various scenarios to demonstrate its reliability and efficiency. في السيناريوهات الواقعية، يتأثر الأداء الديناميكي لمجموعة الشبكات الصغيرة إلى حد كبير بالطاقة المتقطعة لمصادر الطاقة المتجددة والتغيرات المتكررة في الحمل. لمعالجة هذه المشكلة، تم تصميم وحدة تحكم ثانوية ثنائية الطبقة موزعة على أساس الوقت الثابت لتحسين الأداء الديناميكي بين الشبكات الدقيقة وداخلها في غضون وقت استقرار ثابت. وحدة التحكم المقترحة مستقلة عن قيم التشغيل الأولية بدلاً من قانون التحكم في الوقت المحدود. يعمل كل عامل عالمي في شبكة صغرى على التخفيف من عدم تطابق التحميل بين العوامل العالمية الأخرى، في حين يعمل كل عامل محلي في شبكة صغرى على تحقيق مشاركة تيار الحمل المتناسب ومتوسط تنظيم الجهد بينهما في وقت محدد. ومع ذلك، نظرًا لأن تخفيف عدم تطابق التحميل أثناء ظروف الحمل الخفيف يؤثر على كفاءة النظام بسبب الخسائر الكبيرة في الخطوط، تتحول عملية المجموعة إلى نهج تقليل الخسارة الموزعة، والذي يعمل باستخدام القياسات عبر الإنترنت من الشبكات الصغيرة المجاورة. لتوصيف طريقة التشغيل في الطبقة السيبرانية العالمية، يتم تحديد نقطة حرجة لعتبة التحميل للمجموعة. تتم محاكاة أداء المجموعة التي تستخدم الاستراتيجية المقترحة في بيئة ماتلاب/سيمولينك لسيناريوهات مختلفة لإثبات موثوقيتها وكفاءتها.