• Energy Research
• 6. Clean water close
• IN close
• SA close
• BE close
• CM close

In this study, levulinic acid (LA) was produced from rice straw biomass in co-solvent biphasic reactor system consisting of hydrochloric acid and dichloromethane organic solvent. The modified protocol achieved a 15% wt LA yield through the synergistic effect of acid and acidic products (auto-catalysis) and the designed system allowed facile recovery of LA to the organic phase. Further purification of the resulting extractant was achieved through traditional column chromatography, which yielded a high purity LA product while recovering ∼85% wt. Upon charcoal treatment of the resultant fraction generated an industrial grade target molecule of ∼99% purity with ∼95% wt recovery. The system allows the solvent to be easily recovered, in excess of 90%, which was shown to be able to be recycled up to 5 runs without significant loss of final product concentrations. Overall, this system points to a method to significantly reduce manufacturing cost during large-scale LA preparation.

In this study, levulinic acid (LA) was produced from rice straw biomass in co-solvent biphasic reactor system consisting of hydrochloric acid and dichloromethane organic solvent. The modified protocol achieved a 15% wt LA yield through the synergistic effect of acid and acidic products (auto-catalysis) and the designed system allowed facile recovery of LA to the organic phase. Further purification of the resulting extractant was achieved through traditional column chromatography, which yielded a high purity LA product while recovering ∼85% wt. Upon charcoal treatment of the resultant fraction generated an industrial grade target molecule of ∼99% purity with ∼95% wt recovery. The system allows the solvent to be easily recovered, in excess of 90%, which was shown to be able to be recycled up to 5 runs without significant loss of final product concentrations. Overall, this system points to a method to significantly reduce manufacturing cost during large-scale LA preparation.

Considerable interest is being shown in using biochar production from waste biomass with a variety of disciplines to address the most pressing environmental challenges. Biochar produced by the thermal decomposition of biomass under oxygen-limited conditions is gaining popularity as a low-cost amendment for agro-ecosystems. The efficiency of biochar formation is affected by temperature, heating rate, feedstock type, particle size and reactor conditions. Properties such as pH, surface area and ash content of produced biochar increases with increasing temperatures. Biochar produced at lower heating rates may have high porosity and be beneficial for morphological changes in the soil. Biochar can help to enhance soil health and fertility as well as improve agricultural yield. As a result, biochar can assist in increasing food security by promoting sustainable agricultural systems and preserving an eco-friendly environment. Biochar is also widely being used as a sorbent for organic and inorganic pollutants, owing to its large surface area, allowing it to be immobilized from soil with ease. The functional groups and charges present on the surface of biochar play an important role in pollutants removal. This review focuses on the mechanisms of biochar production using different waste materials as a feed stock, factors that influence biochar quality as well as application of biochar in agricultural soil and their reclamation as well. This article also discusses knowledge gaps and future perspectives in the field of biochar-based toxic-pollution remediation.

Considerable interest is being shown in using biochar production from waste biomass with a variety of disciplines to address the most pressing environmental challenges. Biochar produced by the thermal decomposition of biomass under oxygen-limited conditions is gaining popularity as a low-cost amendment for agro-ecosystems. The efficiency of biochar formation is affected by temperature, heating rate, feedstock type, particle size and reactor conditions. Properties such as pH, surface area and ash content of produced biochar increases with increasing temperatures. Biochar produced at lower heating rates may have high porosity and be beneficial for morphological changes in the soil. Biochar can help to enhance soil health and fertility as well as improve agricultural yield. As a result, biochar can assist in increasing food security by promoting sustainable agricultural systems and preserving an eco-friendly environment. Biochar is also widely being used as a sorbent for organic and inorganic pollutants, owing to its large surface area, allowing it to be immobilized from soil with ease. The functional groups and charges present on the surface of biochar play an important role in pollutants removal. This review focuses on the mechanisms of biochar production using different waste materials as a feed stock, factors that influence biochar quality as well as application of biochar in agricultural soil and their reclamation as well. This article also discusses knowledge gaps and future perspectives in the field of biochar-based toxic-pollution remediation.

The growing population and increasing urbanization have led to a surge in domestic wastewater generation, posing significant challenges for effective and sustainable treatment. The present study demonstrates a novel and sustainable approach for the onsite treatment of domestic wastewater using an integrated settler-based biofilm reactor (ISBR) with efficient biogas generation. The ISBR provides an optimized environment for the growth of biofilm, facilitating the removal of organic pollutants and pathogens. Moreover, the ISBR enables the recovery of a valuable resource in the form of biogas, thus enhancing the overall utility of the treatment process. The performance of the ISBR was comprehensively evaluated at laboratory scale through treating the actual domestic wastewater generated from the hostel of Manipal University Jaipur. The ISBR system was operated under an ambient environment at a hydraulic retention time (HRT) of 24 h. The results demonstrated remarkable efficiency in terms of chemical oxygen demand (COD), total suspended solids (TSS), and coliforms removal, with average removal efficiency being more than 90%. According to the COD mass balance analysis, 48.2% of the influent COD was recovered as bioenergy. The chromatogram revealed a high percentage of methane gas in the collected biogas sample. The field emission scanning electron microscope (FESEM) analysis of the accumulated sludge in the ISBR system depicted the morphology of methanogenic bacteria. Both the experimental and theoretical results confirmed the feasibility and sustainability of the ISBR system at the onsite level.

The growing population and increasing urbanization have led to a surge in domestic wastewater generation, posing significant challenges for effective and sustainable treatment. The present study demonstrates a novel and sustainable approach for the onsite treatment of domestic wastewater using an integrated settler-based biofilm reactor (ISBR) with efficient biogas generation. The ISBR provides an optimized environment for the growth of biofilm, facilitating the removal of organic pollutants and pathogens. Moreover, the ISBR enables the recovery of a valuable resource in the form of biogas, thus enhancing the overall utility of the treatment process. The performance of the ISBR was comprehensively evaluated at laboratory scale through treating the actual domestic wastewater generated from the hostel of Manipal University Jaipur. The ISBR system was operated under an ambient environment at a hydraulic retention time (HRT) of 24 h. The results demonstrated remarkable efficiency in terms of chemical oxygen demand (COD), total suspended solids (TSS), and coliforms removal, with average removal efficiency being more than 90%. According to the COD mass balance analysis, 48.2% of the influent COD was recovered as bioenergy. The chromatogram revealed a high percentage of methane gas in the collected biogas sample. The field emission scanning electron microscope (FESEM) analysis of the accumulated sludge in the ISBR system depicted the morphology of methanogenic bacteria. Both the experimental and theoretical results confirmed the feasibility and sustainability of the ISBR system at the onsite level.

In a study of the electrochemical behavior of low-cyanide silver plating baths and of the properties of the deposits obtained, it was found that the current-potential curve obtained with a solid electrode showed a two-step reduction wave, the height of the first being 1/5 that of the second. Analysis of the results of polarographic and rotating disk electrode measurmenents sugests that the rate-controlling steps wereAgCN+e-_??_Ag+CN-……(1)Ag(CN)2-+e-_??_Ag+2CN-……(2)for the first and second waves respectively. The Tafel plots of the two waves showed linear relationships at their rising portions, and the reactions are accordingly concluded to be slow chargetransfer controlled.In baths to which selenocyanate ion was added, the increase in current was markedly greater for the second wave than for the first, and the wave was shifted to the positive side. Potential decay curves for the baths containing selenocyanate ion obtained by the current interrupter method showed lower differential capacities than those for baths that were free of selenocyanate ion. This indicates that the selenocyanate ions were adsorbed preferentially at the electrode, suppress the adsorption of cyanide ions and enhancing the silver deposition reaction.Deposits obtained by jet plating were matt at current densities lower than 50A/dm2, and their appearance was not affected by the addition of selenocyanate ion. At above 50A/dm2, deposits obtained from selenocyanate-free baths were burnt, but deposits obtained from baths with selenocyanate ion added were mirror-bright with a strong (200) orientation up to around 150A/dm2.

In a study of the electrochemical behavior of low-cyanide silver plating baths and of the properties of the deposits obtained, it was found that the current-potential curve obtained with a solid electrode showed a two-step reduction wave, the height of the first being 1/5 that of the second. Analysis of the results of polarographic and rotating disk electrode measurmenents sugests that the rate-controlling steps wereAgCN+e-_??_Ag+CN-……(1)Ag(CN)2-+e-_??_Ag+2CN-……(2)for the first and second waves respectively. The Tafel plots of the two waves showed linear relationships at their rising portions, and the reactions are accordingly concluded to be slow chargetransfer controlled.In baths to which selenocyanate ion was added, the increase in current was markedly greater for the second wave than for the first, and the wave was shifted to the positive side. Potential decay curves for the baths containing selenocyanate ion obtained by the current interrupter method showed lower differential capacities than those for baths that were free of selenocyanate ion. This indicates that the selenocyanate ions were adsorbed preferentially at the electrode, suppress the adsorption of cyanide ions and enhancing the silver deposition reaction.Deposits obtained by jet plating were matt at current densities lower than 50A/dm2, and their appearance was not affected by the addition of selenocyanate ion. At above 50A/dm2, deposits obtained from selenocyanate-free baths were burnt, but deposits obtained from baths with selenocyanate ion added were mirror-bright with a strong (200) orientation up to around 150A/dm2.