• Energy Research
• other engineering and technologies close
• 7. Clean energy close
• 11. Sustainability close
• IT close
• ES close

Abstract To achieve the EU climate and energy objectives, a transition towards a future sustainable energy system is needed. The integration of the huge potential for industrial waste heat recovery into smart energy system represents a main opportunity to accomplish these goals. To successfully implement this strategy, all the several stakeholders' conflicting objectives should be considered. In this paper an evolutionary multi-objective optimization model is developed to perform a sustainability evaluation of an energy system involving an industrial facility as the waste heat source and the neighbourhood as district heating network end users. An Italian case study of heat recovery from a steel casting facility shows how the model allows to properly select the district heating network set of users to fully exploit the available waste energy. Design directions such as the thermal energy storage capacity can be also provided. Moreover, the model enables the analysis of the trade-off between the stakeholders’ different perspectives, allowing to identify possible win-win solutions for both the industrial sector and the citizenship.

This study focuses on formulating the most sustainable concrete by incorporating recycled concrete aggregates and other products retrieved from construction and demolition (C&D) activities. Both recycled coarse aggregates (RCA) and recycled fine aggregates (RFA) are firstly used to fully replace the natural coarse and fine aggregates in the concrete mix design. Later, the cement rich ultrafine particles, recycled glass powder and mineral fibres recovered from construction and demolition wastes (CDW) are further incorporated at a smaller rate either as cement substituent or as supplementary additives. Remarkable properties are noticed when the RCA (4–12 mm) and RFA (0.25–4 mm) are fully used to replace the natural aggregates in a new concrete mix. The addition of recycled cement rich ultrafines (RCU), Recycled glass ultrafines (RGU) and recycled mineral fibres (RMF) into recycled concrete improves the modulus of elasticity. The final concrete, which comprises more than 75% (wt.) of recycled components/materials, is believed to be the most sustainable and green concrete mix. Mechanical properties and durability of this concrete have been studied and found to be within acceptable limits, indicating the potential of recycled aggregates and other CDW components in shaping sustainable and circular construction practices. The authors wish to acknowledge the financial support from EU Horizon 2020 Project VEEP ‘‘Cost-Effective Recycling of C&DW in High Added Value Energy Efficient Prefabricated Concrete Compo-nents for Massive Retrofitting of our Built Environment” (No.723582).

AbstractThis report illustrates the experimental data associated with solar overheating. The experimental data has validated an analytical model which allows for the study of the influences a primary circuit's design has on the overheating of the solar tank.Secondly, the report includes a study of the stagnation in a solar facility. The evolution of the temperature in the hydraulic circuit by means of its measurement at 30 different points, together with the data of the pressure and flow, allow for the real behavior of the solar installation in stagnation conditions to be investigated.Finally, the study shows the measurements obtained on a solar thermal installation located in Alicante (southern Spain). Every installation has been monitored for several months and the main temperatures and pressures around the solar circuit have been noted. The measurements and their processing have allowed for the detection of overheating and stagnation problems in real operating conditions.

Abstract AP1000® Generation III+ reactor bases its safety concept on passive systems, differently from the previous Generation II reactors. This fact has led the approximations and methodologies previously used for modeling active safety systems to be reviewed and adapted to simulate the physics of passive systems. Diverse studies about the AP1000 containment have demonstrated the difficulty to correctly model the occurring phenomenology. In this paper, an integral AP1000 3D containment GOTHIC model is presented, including the Passive Containment Cooling System (PCCS). The model includes the compartments inside and outside the metallic containment liner that influence the thermal–hydraulic behavior. The model is tested against a Large Break Loss of Coolant Accident (LBLOCA) to assess its thermal–hydraulic performance, assuming a PCS tank malfunction, what is a conservative hypothesis. The pressure and temperature evolution predicted by the 3D containment model is analyzed and compared with a single node Lumped Parameters model, allowing to evaluate some preliminary benefits of 3D modeling for containment safety analysis. The 3D containment model allows to predict the thermal evolution in each containment compartment capturing the heterogeneity of this phenomenon, with higher resolution than the lumped parameters models traditionally used in this kind of analyses. It allows to observe the thermohydraulic conditions locally at any time during the transient.

[EN]A systematic approach is developed for the conceptual optimal design of biomethane production via carbon capture. A hybrid heuristic-mathematical procedure is proposed to determine the optimal technology and operating conditions. The heuristic step consists of a literature-based screening of the available technologies. After the prescreening stage, the technologies selected are amine absorption, pressure swing adsorption (PSA), and membrane separation. The mathematical stage is composed of two steps. First, different alternatives for each technology are modeled based on first principles and rules of thumb. These models are used to select the optimal configuration for each process considered. Second, a superstructure model for biomethane production is developed integrating the pre-selected upgrading technologies to select the optimal process, as well as to determine the optimal operating conditions. Four waste sources are analyzed: cattle manure, swine manure, municipal food waste, and sludge. The results suggest that the best amine is diethanolamine (DEA), the best membrane material is the polyimide, and the suggested zeolite is 13X among the ones studied. Finally, among the three technologies, the overall results show that carbon capture using a PSA system using zeolite 13X results in lower production and investment costs, but very close to the use of membranes. The results indicate that food waste shows the lowest production cost for biomethane 0.36 €/Nm3, due to the largest organic matter content, whereas the investment costs are 67 M€, considering a biogas production rate of 0.035 kg of biomethane per kg of waste and the processing of 311 kt/yr of food waste. Credits or incentives are still needed for biomethane to be competitive with fossil natural gas. Junta de Castilla y León y USAL

Given the global energy and environmental situation, the European Union has been issuing directives with increasingly demanding requirements in term of the energy efficiency in buildings. The international competition of sustainable houses, Solar Decathlon Europe (SDE), is aligned with these European objectives. SDE houses are low energy solar buildings that must reach the near to zero energy houses’ goal. In the 2012 edition, in order to emphasize its significance, the Energy Efficiency Contest was added. SDE houses’ interior comfort, functioning and energy performance is monitored. The monitoring data can give an idea about the efficiency of the houses. However, a jury comprised by international experts is responsible for carrying out the houses energy efficiency evaluation. Passive strategies and houses services are analyzed. Additionally, the jury's assessment has been compared with the behavior of the houses during the monitoring period. Comparative studies make emphasis on the energy aspects, houses functioning and their interior comfort. Conclusions include thoughts related with the evaluation process, the results of the comparative studies and suggestions for the next competitions.

[EN] There is an attempt nowadays to provide a more comprehensive and realistic safety assessment of design and operation of Nuclear Power Plants. In this context, innovative approaches are being proposed for safety assessment of nuclear power plants design including both design basis conditions and design extension conditions. An area of research aims at developing methods for combining insights from probabilistic and deterministic safety analyses in Option 4, also called realistic approach, from the International Atomic Energy Agency specific safety guide. The development of Option 4 or realistic approach involves the adoption of best estimate computer codes, best estimate assumptions on systems availability and best estimate of initial and boundary conditions for the safety analysis. This paper focusses on providing the fundamentals and practical implementation of an approach to integrate PSA-based probabilistic models and data, which incorporate best estimate assumptions on the availability of safety systems, into Option 4. It is presented a practical approach to identify relevant, i.e. most probable, configurations of safety systems and to assess the associated occurrence probability of each configuration using PSA models and data of a NPP, which is based on the use of a Pure Monte Carlo method. An example of application is provided to demonstrate how this approach performs. The case study focusses on an accident scenario corresponding to the initiating event Loss Of Feed Water (LOFW) for a typical three-loops Pressurized Water Reactor (PWR) NPP. Authors are grateful to the Spanish CSN (Consejo de Seguridad Nuclear) for the financial support of this research (Research Project SIN/4078/2013/640; MASA Project).

[EN] Renewable energies are a central element in the search for energy sustainability, so they are becoming a substantial component of the energy scenario of every country, both as systems connected to the grid or in stand-alone applications. Feasibility of these renewable energy systems could be necessary not only in their application in isolated areas, but also in systems connected to the grid, in this last case when their contribution reaches a substantial fraction of the total electricity demand. To overcome this reliability problem, hybrid renewable systems could become essential and activities to optimize their design should be addressed, both in the simulation and in the experimental areas. In this paper, a laboratory to simulate and verify the reliability of hybrid renewable systems is presented and its application to the feasibility analysis of multicomponent systems including photovoltaic panels, wind generator and biomass gasification plant, plus energy storage in a battery bank, are described.