• Energy Research
• IT close
• ES close
• Energies close

This research presents a 100% renewable energy (RE) scenario by 2050 with a high share of electric vehicles on the grid (V2G) developed in Ecuador with the support of the EnergyPLAN analysis tool. Hour-by-hour data iterations were performed to determine solutions among various features, including energy storage, V2G connections that spanned the distribution system, and long-term evaluation. The high participation in V2G connections keeps the electrical system available; meanwhile, the high proportions of variable renewable energy are the pillar of the joint electrical system. The layout of the sustainable mobility scenario and the high V2G participation maintain the balance of the electrical system during most of the day, simplifying the storage equipment requirements. Consequently, the influence of V2G systems on storage is a significant result that must be considered in the energy transition that Ecuador is developing in the long term. The stored electricity will not only serve as storage for future grid use. Additionally, the V2G batteries serve as a buffer between generation from diversified renewable sources and the end-use stage.

Research on corona discharge, shared by physics, chemistry and electrical engineering, has not arrested yet. As a dissipative process, the development of corona increases the resistive losses of transmission lines and enhances the line capacitance locally. Introducing additional losses and propagation delay, along the line, non-linearity and non-uniformity of the line parameters; therefore, corona should not be neglected. The present work is meant to provide the reader with comprehensive information on the corona macroscopic phenomenology and development, referring to the most relevant contributions in the literature on this subject. The models proposed in the literature for the simulation of the corona development are reviewed in detail, and sensitivity curves are provided to highlight their dependence on the input parameters.

Nowadays, heating using wood, briquettes, or pellets is a curious replacement to fossil fuels such as coal, oil, or gas. Unfortunately, the combustion of biofuels, especially in low-power boilers with unstable operating conditions, releases a lot of gas pollutants (e.g., carbon monoxide (CO), nitric oxide (NO), and various organic compounds) that are usually generated due to the incomplete product combustion. The combustion of biofuel in grate boilers with top-down ignition is a new approach, popular in society (mainly used for coal fuels), which improves the combustion process and reduces the amount of pollutants emitted. This study evaluated the impact of ignition techniques on the emission level of gas pollutants during the combustion of wood logs, briquettes, and pellets of pine in grate-based charging boilers. The combination of top ignition mode with pinewood logs allowed us to achieve a reduction of 6% in CO and sulfur dioxide (SO2) emission into the atmosphere. However, the combination of top-down ignition mode with pellets and briquettes produced, in fully operational conditions, 1- to 18-fold higher levels of CO and SO2 respectively, than bottom-up ignition, after an initial period of low level CO and SO2 emissions. During the tests (mainly with ignition from top), substantial emissions of NO were observed of up to 400 mg·m−3 at 10% O2. Therefore, further research is required to decrease emission related to the content of nitrogen in biomass. In this respect, research of impact on the combustion temperature of such emissions is needed.

Microbial electrochemical technologies (METs) constitute the core of a number of emerging technologies with a high potential for treating urban wastewater due to a fascinating reaction mechanism—the electron transfer between bacteria and electrodes to transform metabolism into electrical current. In the current work, we focus on the model electroactive microorganism Geobacter sulfurreducens to explore both the design of new start-up procedures and electrochemical operations. Our chemostat-grown plug and play cells, were able to reduce the start-up period by 20-fold while enhancing chemical oxygen demand (COD) removal by more than 6-fold during this period. Moreover, a filter-press based bioreactor was successfully tested for both acetate-supplemented synthetic wastewater and real urban wastewater. This proof-of-concept pre-pilot treatment included a microbial electrolysis cell (MEC) followed in time by a microbial fuel cell (MFC) to finally generate electrical current of ca. 20 A·m−2 with a power of 10 W·m−2 while removing 42 g COD day−1·m−2. The effective removal of acetate suggests a potential use of this modular technology for treating acetogenic wastewater where Geobacter sulfurreducens outcompetes other organisms.

The hygrothermal behaviour of an internally insulated historic wall is still hard to predict, mainly because the physical characteristics of the materials composing the historic wall are unknown. In this study, the hygrothermal assessment of an internally thermal insulated masonry wall of an historic palace located in Ferrara, in Italy, is shown. In situ non-destructive monitoring method is combined with a hygrothermal simulation tool, aiming to better analyse and discuss future refurbishment scenarios. In this context, the original U-value of the wall (not refurbished) is decreased from 1.44 W/m2K to 0.26 W/m2K (10 cm stone wool). Under the site specific conditions of this wall, not reached by the sun or rain, it was verified that even in the absence of vapour barrier, no frost damage is likely to occur and the condensation risk is very limited. Authors proposed further discussion based on simulation. The results showed that the introduction of a second gypsum board to the studied technology compensated such absence, while the reduction of the insulation material thickness provides a reduction of RH peaks in the interstitial area by 1%; this second solution proved to be more efficient, providing a 3% RH reduction and the avoidance of further thermal losses.

The injection of apparent power to self-consumption buses generates voltage variations during network operation, which, when properly monitored, could support voltage regulation and control. In this paper, we propose a linear sensitivity modelling, quite useful for studies of voltage regulation with distributed energy resources (DER). This modelling consists of two analytical improvement steps: first, a full formulation for the voltage deviations, and second, the influence of line capacitance as Q-injections at the points of common couplings (PCCs). Our proposal is based on the linear topological sensitivity of an existing network (as a function of the line parameters X, R, and Bc), branch power flow (active–reactive power (P-Q)), and power injections at the PCCs. Here, the linear sensitivity algorithm is applied to a modified IEEE 33-bus distribution system to demonstrate its extended effectiveness to voltage monitoring and control scenarios. Its application estimates and compensates in a better way the voltage deviations with regard to the operating desired voltage (|V|op) constraints, using distributed power injections at the PCCs. Numerical results always showed a curtailment of the relative error against common simplifications of the electrical modelling in steady-state, thus simulating two critical scenarios of operation production–consumption for the existing system response. The proposed algorithm was validated considering as reference the voltage profile outputs of the load flow analysis, using the Newton–Raphson method via DIgSILENT, in terms of its accuracy, silhouette shape along the feeder and with regard to the application of reactive compensation as an analytical case study for voltage improvement in active distribution networks.

The global energy crisis has spurred increased investments in energy efficiency and clean energy initiatives; however, the results have fallen short of expected effectiveness. Concurrently, population growth and urbanisation drive a persistent surge in energy demands, especially within the residential sector, significant to overall building energy consumption. Current research focuses on residents’ responses to one-shot investments for energy efficiency or clean sources. The renovation wave, involving a massive number of existing buildings, calls for the mobilisation of huge investments that can be hard to afford in the short run. Sustainable behavioural change is complementarily rising as a key asset for maximising the overall estimated energy saving potential. Despite significant efforts to analyse household energy use and promote behavioural transformations, the literature remains gaping about future users, particularly the younger generation, as future leaders of sustainable development who exhibit a more responsible approach towards climate-related issues but also a strong dependency on digital-based solutions, which may influence energy use patterns and living habits, also impacting relations among peers and overall societal sustainability and energy efficiency. This article proposes a systematic literature review to analyse the variables affecting young people’s energy behaviour at home. The aim is to investigate the engines and gaps between strategies or tools for behaviour change and the expected effects, then find potential methods to address that barrier to identify a more promising approach, encouraging the younger generation to translate towards more sustainable energy behaviours.

The proposed special issue (SI) has invited submissions related to renewable energy, energy storage, power converters and electric drive systems for electrified transportation and smart grid applications [...]