• Energy Research
• Restricted close
• other engineering and technologies close
• IT close
• NL close

Diesel engine exhausts from a common rail 3.0 L F1C diesel engine were analyzed at two different load conditions of the WLTC testing cycle downstream of both the diesel particulate filter (DPF) and selective catalytic reactor (SCR) to verify their effect on the characteristics of carbon particulate matter. An array of chemical, physical and spectroscopic techniques (gas chromatography coupled with mass spectrometry (GC-MS), mobility analyzer, UV-Visible absorption and fluorescence spectroscopy) was applied for characterizing polycyclic aromatic hydrocarbons (PAH), heavy aromatic compounds and soot, constituting the particulate matter (PM) sampled from the exhaust. The engine was operated in half load (HL) (188 Nm, representing the more common condition for engine in urban traffic) and full load (FL) (452 Nm, representing the best performance of the engine operation) conditions, at the same engine speed (2000 rpm). Soot formation was enhanced in HL condition, with respect to FL, but, just because of the much lower soot amount, the after-treatment systems in this last condition resulted to be less efficient in the soot abatement. Indeed, the abatement through DPF was about 40% lower in the FL condition with respect to HL condition, and any significant further concentration decrease was found after SCR, in both conditions. By contrast, PAH concentration after DPF abatement was found to be higher in the HL with respect to FL condition. A further PAH concentration decrease of about 30% was found after the SCR in the HL condition whereas in FL the reduction was only about 5-6%. Also the heavy aromatic compounds having molecular weight above the GC-MS detection limit (300 u), were mitigated by SCR. Therefore, SCR did not cause a further soot reduction, whereas it was effective in largely reducing PAH and heavy aromatics emissions, especially in the lower temperature condition featuring the half-load condition, when combustion efficiency is worse. Moreover, SCR system reduced the emission of small particles probably due to an enhanced agglomeration of particles, with beneficial effect on the harmfulness to human health.

Capítulos en libros This paper describes a strategic information platform developed for the German electric utility Eon, to provide historical bidding analysis and medium-term forecasting of the Iberian Electricity Market. This platform, PLAMER, has three main modules: Initialization module, consisting of different sub-modules to define the electrical system structure and to organize the input data of the rest of modules, PLAMER-bids, to read, aggregate and visualize market historical bids and also to prepare them for their future forecasted values, and PLAMER-clearing, for market clearing emulation using forecasted bids. PLAMER-clearing models the Iberian market based on a bid clearing mechanism with an inherent market splitting procedure. This market splitting is built with a bi-nodal simplification, one node representing the Spanish System and the other the Portuguese one. Both are simply connected by a unique equivalent interconnection line. The medium term clearing model uses a generation portfolio per generation company in terms of technologies, for supplying monthly demand for different load levels, and labour and non-labour periods. Some technical constraints, such as minimum outputs and pumping energy balance, are also taking into account. The mathematical problem of PLAMER-clearing is a quadratic programming model solved using GAMS language and CPLEX optimizer. Finally, a real Iberian case study is detailed and some market splitting outputs are analyzed. info:eu-repo/semantics/publishedVersion

This paper presents results of an online stated choice experiment on preferences of Dutch private car owners for alternative fuel vehicles (AFVs) and their characteristics. Results show that negative preferences for alternative fuel vehicles are large, especially for the electric and fuel cell car, mostly as a result of their limited driving range and considerable refueling times. Preference for AFVs increases considerably with improvements on driving range, refueling time and fuel availability. Negative AFV preferences remain, however, also with substantial improvements in AFV characteristics; the remaining willingness to accept is on average € 10,000-€ 20,000 per AFV. Results from a mixed logit model show that consumer preferences for AFVs and AFV characteristics are heterogeneous to a large extent, in particular for the electric car, additional detour time and fuel time for the electric and fuel cell car. An interaction model reveals that annual mileage is by far the most important factor that determines heterogeneity in preferences for the electric and fuel cell car. When annual mileage increases, the preference for electric and fuel cell cars decreases substantially, whilst the willingness to pay for driving range increases substantially. Other variables such as using the car for holidays abroad and the daily commute also appear to be relevant for car choice. © 2014 Elsevier Ltd.

Climaps.eu is an online atlas providing data, visualizations and commentaries about climate adaptation debate. It contains 33 issue-maps and 5 issue-stories. Each of the maps focuses on one issue in the adaptation debate and provides.The atlas is addressed to climate experts (negotiators, NGOs and companies concerned by global warming, journalists…) and to citizens willing to engage with the issues of climate adaptation.It employs advanced digital methods to deploy the complexity of the issues related to climate adaptation and information design to make this complexity legible.

[object Object]

In the anodisation of Nb in acidic fluoride solutions or warm aqueous alkali, and in that of Mo in concentrated phosphoric acid, impedance spectroscopy provides evidence that 3D film growth proceeds already during the active–passive transition. Indeed, linear potential dependences of both the inverse of the high-frequency capacitance and of the product of the high-frequency resistance times the steady-state current are observed already below the peak potential. Simultaneously, a pseudo-inductive loop at intermediate frequencies is detected in the impedance spectra. In the present paper, we propose a kinetic model for the interpretation of these data. The model assumes that the metal is covered with a non-stoichiometric oxide containing at least two oxidation states of the cation. The processes of oxidative dissolution of the lower valence cations and their transformation to cations of higher valence, leading to passivation, explain the shape of the I–E curve. These processes are limited by both charge transfer at the film–solution (F/S) interface and transport of cation vacancies through the film. Thickening of the oxide film is assumed to proceed simultaneously, and is limited by transport of oxygen vacancies accelerated by an interfacial charge of cation vacancies.

The modern Common Rail Diesel engine are, normally, optimised for being fuelled with the commercial Diesel fuel. The ECU calibrations are, consequently, defined to obtain the correct compromise between performances and emissions. It is, so, clear that if the engine is fuelled with an alternative bio-fuel with different characteristics (net heating value, stoichiometric A/F ratio, density, viscosity, etc.) the calibration must be modify. Interest in fuels from renewable sources and their use in transport has grown over the last decade. This is because of their biodegradability, potential improvements in exhaust emissions and benefits on the virtuous CO2 cycle of the earth. This paper demonstrates that it is possible to optimise the emissions and the performances of a light duty diesel C.R. engine fuelled with a vegetable derived fuel (Rapeseed Methyl-Ester) pure or blended with commercial Diesel fuel. Particularly in this paper the experimental results and the ECU control solutions referring to different fuel compositions are shown.

This paper is focused on the measurement issues and procedures for the characterization of medium voltage grids for narrowband power line communications (NB-PLCs), in the perspective of the use and integration of such technology into smart grids communication networks. The fundamentals are given for the characterization of the PLC channel, by means of noise and attenuation measurements. Suitable procedures are also developed for the characterization and modeling of the power system components in the frequency range of interest. Furthermore, the complete model of the PLC system is experimentally validated in a real case study.

In this paper some preliminary experimental results on a Zebra battery based propulsion system for urban bus applications are presented. The tests were carried out using a laboratory 1:1 scale test bench, composed by a 65 kW electric drive, specifically designed for urban bus applications, supplied by two 20 kWh Zebra batteries connected in parallel. The electric power train was tested on a laboratory bench, connected through a fixed ratio gear box to a 100 kW regenerative electric brake provided with speed and torque controls, in order to evaluate the propulsion system performance in steady state operative conditions. The obtained preliminary experimental results were utilized to implement a Matlab-Simulink model of urban bus, which might be powered by the same electric propulsion system studied. Thanks to this model it was possible to evaluate the dynamic behavior of the urban bus, working on standard driving cycles, taking into account the resistant forces represented by proper vehicle/road/aerodynamic parameters. An evaluation of the expected real vehicle driving range was also estimated in different road conditions.