• Energy Research
• 2016-2025close
• Restricted close
• NL close
• IT close

Diesel engine exhausts from a common rail 3.0 L F1C diesel engine were analyzed at two different load conditions of the WLTC testing cycle downstream of both the diesel particulate filter (DPF) and selective catalytic reactor (SCR) to verify their effect on the characteristics of carbon particulate matter. An array of chemical, physical and spectroscopic techniques (gas chromatography coupled with mass spectrometry (GC-MS), mobility analyzer, UV-Visible absorption and fluorescence spectroscopy) was applied for characterizing polycyclic aromatic hydrocarbons (PAH), heavy aromatic compounds and soot, constituting the particulate matter (PM) sampled from the exhaust. The engine was operated in half load (HL) (188 Nm, representing the more common condition for engine in urban traffic) and full load (FL) (452 Nm, representing the best performance of the engine operation) conditions, at the same engine speed (2000 rpm). Soot formation was enhanced in HL condition, with respect to FL, but, just because of the much lower soot amount, the after-treatment systems in this last condition resulted to be less efficient in the soot abatement. Indeed, the abatement through DPF was about 40% lower in the FL condition with respect to HL condition, and any significant further concentration decrease was found after SCR, in both conditions. By contrast, PAH concentration after DPF abatement was found to be higher in the HL with respect to FL condition. A further PAH concentration decrease of about 30% was found after the SCR in the HL condition whereas in FL the reduction was only about 5-6%. Also the heavy aromatic compounds having molecular weight above the GC-MS detection limit (300 u), were mitigated by SCR. Therefore, SCR did not cause a further soot reduction, whereas it was effective in largely reducing PAH and heavy aromatics emissions, especially in the lower temperature condition featuring the half-load condition, when combustion efficiency is worse. Moreover, SCR system reduced the emission of small particles probably due to an enhanced agglomeration of particles, with beneficial effect on the harmfulness to human health.

Originally developed and validated at the Cabauw (Netherlands) topographically flat onshore location, the alpha-I wind resource extrapolating method was tested at the FINO3 offshore site in the North Sea (Germany). The aim was to prove its validity also when applied over a substantially different environment in terms of surface characteristics and stability conditions. Data from local mast at 30, 80, and 100 m were used, with extrapolations to 80-m and 100-m turbine hub heights accomplished based on 30-m turbulence intensity observations. Trained over a 2-year period (2011-2012), the method was validated on year 2013. Similarly to the onshore application, the method was reliable in extrapolating wind speed to both 80 m and 100 m, with bias within 5%, NRMSE = 0.20 and r = 0.94. Conversely, scores were largely better than at the onshore site in predicting the annual energy yield, biased by 0.41-1.02% at 80 m, and 1.12-1.36% at 100 m. The method proved to be highly sensitive to the stability classification, as not considering this option increased its biases to 4.51-5.93% at 80 m, and 7.46-8.23% at 100 m. Method's reliability might suitably help reduce the number of masts installed throughout a large offshore area.

Energy companies trading in derivatives which have a value based on an energy product ( “Energy Trading”) are subjected to a fragmented regulatory framework. They are supervised by a multitude of authorities on a national and European level. These authorities cooperate horizontally (between EU agencies or between national regulatory authorities) or vertically – between EU agencies and NRA’s) and in a formal and informal way. They share information on Energy Trading to detect market abuse. This article aims to provide insight in the effectiveness of supervisory activities within the Energy Trading landscape. In doing so, the obligation for energy companies to report fundamental data on the derivatives they trade in, is used for illustrative purposes and explained in light of the European Market Infrastructure Regulation (‘EMIR’), the Markets in Financial Instruments Directive and Regulation (‘MiFID II and MiFIR’) and the regulation on wholesale energy market integrity and transparency (‘REMIT’). The article finishes with a conclusion which advocates the necessity of information sharing and professional secrecy in the current regulatory landscape and intends to contribute to a discussion on the effectiveness of information sharing within an international context.

Sul mercato esistono molti materiali adsorbenti (prevalentemente a base di carboni attivi eventualmente impregnati, zeoliti, alcuni ossidi metallici) per la desolforazione e la rimozione di VOC anche a temperatura e pressione ambiente. Tuttavia questi materiali mostrano capacità relativamente basse e/o cinetiche di cattura lente a temperatura ambiente, che inevitabilmente si traducono nella necessità di utilizzare grandi volumi di impianto. La ricerca svolta dall'IRC-CNR Napoli e DSC-UNINA, in stretta collaborazione, parte dalla considerazione che lo sviluppo di nuovi materiali e processi ad alta efficienza per la desolforazione (in particolare attraverso adsorbimento) rappresenta un traguardo cruciale per l'impiego vantaggioso di una fonte energetica rinnovabile e residuale quale il biogas, anche su piccola scala in un'ottica di generazione distribuita di energia. La ricerca è stata indirizzata allo sviluppo di materiali adsorbenti ad alte prestazioni e basso costo in grado di far fronte a condizioni operative assai diversificate in termini di temperature (già a partire da temperatura ambiente) e composizioni dei gas da trattare (es. presenza di altri inquinanti).

Green tea catechins mixed with caffeine have been proposed as adjuvants for maintaining or enhancing energy expenditure and for increasing fat oxidation, in the context of prevention and treatment of obesity. These catechins-caffeine mixtures seem to counteract the decrease in metabolic rate that occurs during weight loss. Their effects are of particular importance during weight maintenance after weight loss. Other metabolic targets may be fat absorption and the gut microbiota composition, but these effects still need further investigation in combination with weight loss. Limitations for the effects of green tea catechins are moderating factors such as genetic predisposition related to COMT-activity, habitual caffeine intake, and ingestion combined with dietary protein. In conclusion, a mixture of green tea catechins and caffeine has a beneficial effect on body-weight management, especially by sustained energy expenditure, fat oxidation, and preservation of fat free body-mass, after energy restriction induced body-weight loss, when taking the limitations into account.

This paper aims to correlate the in-cylinder soot formation and the exhaust particle emissions for different methods of gasoline/ethanol fueling in spark ignition engine. In particular, the engine was fueled with gasoline and ethanol separately and not, in this latter case both blended (E30) and dual fueled (EDF). For E30 the bend was direct injected and for EDF, the ethanol was injected in the combustion chamber and the gasoline into the intake duct. For both the injection configurations, the same percentage of ethanol in gasoline was supplied: 30%v/v. The measurements were carried out at 2000 and 4000 rpm, under full load, and stoichiometric condition, in small single cylinder optical engine. 2D-digital imaging was performed to follow the combustion process with a high spatial and temporal resolution through a full-bore optical piston. The two-color pyrometry was applied for the analysis of the in cylinder soot formation in the combustion chamber. Particle mass concentration was evaluated at the exhaust by means of a smoke meter. The particle size distribution function was measured in the range from 5.6 to 560 nm by an Engine Exhaust Particle Sizer (EEPS). It was observed that the use of ethanol allows the reduction of soot formation and particles emission in DI configuration. However, for E30 the in-cylinder soot formation and emissions are larger than EDF. This result is mainly due to the different contribution of gasoline. Optical analysis shows that in E30 the direct injected gasoline causes wide diffusive flames where soot formation is promoted; whereas for EDF the better evaporation and mixing of gasoline, typical of PFI configuration, results in few, small, and localized diffusive flames producing smaller particle emissions.

In the last years, even more attention was paid to the alternative fuels that allow both reducing the fossil fuel consumption and the pollutant emissions. Gaseous fuels like methane and hydrogen are the most interesting in terms of engine application. This paper reports a comparison between methane and different methane/hydrogen mixtures in a single-cylinder Port Fuel/Direct Injection spark ignition (PFI/DI SI) engine operating under steady state conditions. It is representative of the gasoline engine for automotive application. Engine performance and exhaust emissions were evaluated. Moreover, 2D-digital cycle resolved imaging was performed with high spatial and temporal resolution in the combustion chamber. In particular, it allows characterizing the combustion by means of the flame propagation in terms of mean radius and velocity. Moreover, the interaction of turbulence with the local flame was evaluated. For both the engine configurations, it was observed that the addition of hydrogen results in a more efficient combustion, even though the engine configuration plays an important role. In PFI mode, the lower density of hydrogen causes a lower energy input. In DI mode, instead, the larger hydrogen diffusivity counteracts the charge stratification especially for larger hydrogen content. © 2016 Elsevier Ltd. All

Climate change forces society to adapt. Adaptation strategies are preferably based on the best available climate information. Climate projections, however, often inform adaptation strategies after being interpreted once or several times. This process affects the original message put forward by climate scientists when presenting the basic climate projections, in particular regarding uncertainties. The nature of this effect and its implications for decision-making are as yet poorly understood. This chapter explores the nature and consequences of (a) the communication tools used by scientists and experts and (b) changes in the communicated information as it travels through the decision-making process. It does so by analyzing observatories; the interpretative steps taken in a sample of 25 documents, pertaining to the field of public policies for climate change impact assessment and adaptation strategies. Five phases in the provisioning of climate information are distinguished: pre-existing knowledge (i.e., climate models and data), climate change projection, impact assessment, adaptation strategy, and adaptation plan. Between the phases, climate information is summarized and synthesized in order to be passed on. The results show that in the sample, information on uncertainty is underrepresented: e.g., studies focus on only one scenario and/or disregard probability distributions. In addition, visualization tools are often used ineffectively, leading to confusion and unintended interpretations. Several recommendations are presented. While climatologists need better training in communication issues, decision-makers also need training in climatology to adopt more cautious and robust adaptation strategies that account for the uncertainty inherent in climate projections.

Due to the increasing awareness of climate change, depletion of natural resources, and increasing world population, companies in the agri-food sector need to redesign their existing supply chains and take into account both the economic and environmental impact of their operations. In practice not all the required information is available in advance due to various sources of uncertainty in agri-food supply chains. In this research a multi-objective two-stage stochastic programming model is proposed to analyse and evaluate the economic and environmental impacts to account for uncertainty in agri-food supply chains. A mushroom supply chain in the Netherlands is presented as an illustrative case study. Optimal production planning decisions calculated with a two-stage stochastic programming model are compared with the results of an equivalent deterministic model. The results of the optimizations show that accounting for stochasticity in important model parameters can reduce the difference between expected and realized economic performance by approximately 4% on average. Moreover, this paper demonstrates that including stochastic model parameters can reduce the environmental impact without compromising the current economic performance. Given the assumptions in the setup of the case study and the available information, it is concluded that applying a 2-stage stochastic programming approach for production planning decisions can lead to improved economic and environmental performance in an agri-food supply chain. New findings in real-life case studies are needed to get profound insights and understanding on the impact of uncertainty on production planning decisions in sustainable agri-food supply chains.