• Energy Research
• other engineering and technologies close
• IT close
• CNR ExploRA close

Sentinel-2 data have been used in various fields of human activity. In cultural heritage, their potential is still to be fully explored. This paper aims to illustrate how remote sensing and open source tools are useful for archaeological investigations. The whole issue revolves around the application of satellite (Sentinel-2) and accessory tools for the identification, knowledge and protection of the cultural heritage of two areas of southern Italy: Sant’Arsenio (SA) and Foggia (FG). Both study cases were selected for a specific reason: to demonstrate the usefulness of open data and software for research and preservation of cultural heritage, as in the case of urban sprawl, development of public works (gas- and oil-pipelines, etc.) or intensive use of land for agricultural purposes. The results obtained are relevant for the knowledge improvement and very useful to operate in the field of preventive archaeology, for the evaluation and management of risk, the planning of city-expansion or infrastructures that could damage the buried heritage.

Diesel engine exhausts from a common rail 3.0 L F1C diesel engine were analyzed at two different load conditions of the WLTC testing cycle downstream of both the diesel particulate filter (DPF) and selective catalytic reactor (SCR) to verify their effect on the characteristics of carbon particulate matter. An array of chemical, physical and spectroscopic techniques (gas chromatography coupled with mass spectrometry (GC-MS), mobility analyzer, UV-Visible absorption and fluorescence spectroscopy) was applied for characterizing polycyclic aromatic hydrocarbons (PAH), heavy aromatic compounds and soot, constituting the particulate matter (PM) sampled from the exhaust. The engine was operated in half load (HL) (188 Nm, representing the more common condition for engine in urban traffic) and full load (FL) (452 Nm, representing the best performance of the engine operation) conditions, at the same engine speed (2000 rpm). Soot formation was enhanced in HL condition, with respect to FL, but, just because of the much lower soot amount, the after-treatment systems in this last condition resulted to be less efficient in the soot abatement. Indeed, the abatement through DPF was about 40% lower in the FL condition with respect to HL condition, and any significant further concentration decrease was found after SCR, in both conditions. By contrast, PAH concentration after DPF abatement was found to be higher in the HL with respect to FL condition. A further PAH concentration decrease of about 30% was found after the SCR in the HL condition whereas in FL the reduction was only about 5-6%. Also the heavy aromatic compounds having molecular weight above the GC-MS detection limit (300 u), were mitigated by SCR. Therefore, SCR did not cause a further soot reduction, whereas it was effective in largely reducing PAH and heavy aromatics emissions, especially in the lower temperature condition featuring the half-load condition, when combustion efficiency is worse. Moreover, SCR system reduced the emission of small particles probably due to an enhanced agglomeration of particles, with beneficial effect on the harmfulness to human health.

In this paper, the modifications realized to make optically accessible a commercial high performance spark ignition and direct injection (DI) 4-cylinder engine are reported. The engine has been designed trying to keep as much as possible its thermo-fluid dynamic configuration in order to maintain its performance and emissions. Two optical accesses have been realized in order to interfere as little as possible with the combustion chamber geometry. A first optical access has been achieved in the piston head and a second by inserting an endoscopic fiber probe in the head. Preliminary results demonstrated that this optical assessment responds to the design targets and allowed a characterization of a commercial GDI engine working with homogeneous and stratified charge mode.

[object Object]

In the anodisation of Nb in acidic fluoride solutions or warm aqueous alkali, and in that of Mo in concentrated phosphoric acid, impedance spectroscopy provides evidence that 3D film growth proceeds already during the active–passive transition. Indeed, linear potential dependences of both the inverse of the high-frequency capacitance and of the product of the high-frequency resistance times the steady-state current are observed already below the peak potential. Simultaneously, a pseudo-inductive loop at intermediate frequencies is detected in the impedance spectra. In the present paper, we propose a kinetic model for the interpretation of these data. The model assumes that the metal is covered with a non-stoichiometric oxide containing at least two oxidation states of the cation. The processes of oxidative dissolution of the lower valence cations and their transformation to cations of higher valence, leading to passivation, explain the shape of the I–E curve. These processes are limited by both charge transfer at the film–solution (F/S) interface and transport of cation vacancies through the film. Thickening of the oxide film is assumed to proceed simultaneously, and is limited by transport of oxygen vacancies accelerated by an interfacial charge of cation vacancies.

The modern Common Rail Diesel engine are, normally, optimised for being fuelled with the commercial Diesel fuel. The ECU calibrations are, consequently, defined to obtain the correct compromise between performances and emissions. It is, so, clear that if the engine is fuelled with an alternative bio-fuel with different characteristics (net heating value, stoichiometric A/F ratio, density, viscosity, etc.) the calibration must be modify. Interest in fuels from renewable sources and their use in transport has grown over the last decade. This is because of their biodegradability, potential improvements in exhaust emissions and benefits on the virtuous CO2 cycle of the earth. This paper demonstrates that it is possible to optimise the emissions and the performances of a light duty diesel C.R. engine fuelled with a vegetable derived fuel (Rapeseed Methyl-Ester) pure or blended with commercial Diesel fuel. Particularly in this paper the experimental results and the ECU control solutions referring to different fuel compositions are shown.

This paper is focused on the measurement issues and procedures for the characterization of medium voltage grids for narrowband power line communications (NB-PLCs), in the perspective of the use and integration of such technology into smart grids communication networks. The fundamentals are given for the characterization of the PLC channel, by means of noise and attenuation measurements. Suitable procedures are also developed for the characterization and modeling of the power system components in the frequency range of interest. Furthermore, the complete model of the PLC system is experimentally validated in a real case study.

In this paper some preliminary experimental results on a Zebra battery based propulsion system for urban bus applications are presented. The tests were carried out using a laboratory 1:1 scale test bench, composed by a 65 kW electric drive, specifically designed for urban bus applications, supplied by two 20 kWh Zebra batteries connected in parallel. The electric power train was tested on a laboratory bench, connected through a fixed ratio gear box to a 100 kW regenerative electric brake provided with speed and torque controls, in order to evaluate the propulsion system performance in steady state operative conditions. The obtained preliminary experimental results were utilized to implement a Matlab-Simulink model of urban bus, which might be powered by the same electric propulsion system studied. Thanks to this model it was possible to evaluate the dynamic behavior of the urban bus, working on standard driving cycles, taking into account the resistant forces represented by proper vehicle/road/aerodynamic parameters. An evaluation of the expected real vehicle driving range was also estimated in different road conditions.