• Energy Research
• Closed Access close
• Open Source close
• 13. Climate action close
• 12. Responsible consumption close
• JP close

This paper presents a multi-objective optimization model for a long-term generation mix in Indonesia. The objective of this work is to assess the economic, environment, and adequacy of local energy sources. The model includes two competing objective functions to seek the lowest cost of generation and the lowest CO2 emissions while considering technology diffusion. The scenarios include the use of fossil reserves with or without the constraints of the reserve to production ratio and exports. The results indicate that Indonesia should develop all renewable energy and requires imported coal and natural gas. If all fossil resources were upgraded to reserves, electricity demand in 2050 could be met by domestic energy sources. The maximum share of renewable energy that can be achieved in 2050 is 33% with and 80% without technology diffusion. The least cost optimization produces lower generation costs than the least CO2 emissions, as well as the combined scenario. Total CO2 emissions in 2050 are five to six times as large as current emissions. The least CO2 emissions scenario can reduce almost half of the CO2 emissions of the least cost scenario by 2050. The proposed multi-objective optimization model leads some optimal solutions for a more sustainable electricity system.

This paper presents experimental results of the impact of CO(2) co-feed on a gasification/pyrolysis process for various feedstocks (biomass, coal, and municipal solid waste (MSW)). Various feedstocks were thermo-gravimetrically characterized under various atmospheric conditions and heating rates. A substantial amount of char burn out was identified in the presence of CO(2) via a series of thermo-gravimetric analysis tests, which enabled high conversion of final mass (approximately 99%) to be achieved. The impact of CO(2) co-feed on the volatilization regime during the pyrolysis/gasification process was not apparent at a heating rate of 10-40 degrees C min(-1). However, the impact of CO(2) on the volatilization regime at a fast heating rate (950 degrees C min(-1)) was substantial. For example, significant enhancement in the generation of CO, by a factor of approximately 2, was observed in the presence of CO(2). The generation of major chemical species, such as CH(4) and C(2)H(4), were enhanced, but this was not as apparent as in the case with CO. In addition, introducing CO(2) to the pyrolysis/gasification process enabled the amount of condensable liquid hydrocarbons, such as tar (approximately 30-40%) to be significantly reduced in the presence of CO(2), in that injecting CO(2) into the pyrolysis/gasification process expedites cracking the volatilized chemical species. Experimental work confirmed that biomass and MSW could be feasible and desirable feedstocks for the pyrolysis/gasification process as these feedstocks can be easily treated compared to coal. To extend this understanding to a more practical level, various feedstocks were tested in a tubular reactor and drop tube reactor under various experimental conditions.

Abstract It is demonstrated that the fuel deposit has a significant influence on the NOx and particular matter (PM) emissions, especially with the consideration of the more and more strict emission regulations issued by the governments, which results in that the near-nozzle spray has been received the increased attention, recently. In this study, the near-nozzle spray characteristics at the initial and end stages were investigated by a high-resolution camera with a laser as the light source. At the initial stage, microscopic behaviors of the near-nozzle spray were observed at upstream, midstream and downstream, respectively. Moreover, the injection frequency was changed to check the effect on the near-nozzle spray morphology. Next, the micro spray length, width and angle were obtained from the processed images. While, at the end stage, the near-nozzle spray evolutions were observed and characterized at 0.5, 0.3, 0.2 and 0.1 ms before the end of injection (BEOI), the end of injection (EOI), 0.05, 0.1, 0.15 and 0.2 ms after the end of injection (AEOI), respectively. Furthermore, the droplet area, spray area without droplets, droplet number and averaged diameter were calculated. Results show that three structures of the near-nozzle spray at the initial stage can be classified as mushroom, steeple and cylinder shapes. And the injection frequency has an influence on their formations owing to the residual fuel and sucked air AEOI. Moreover, although more droplets can be identified at the end stage with time, it does not indicate the better atomization. On the contrary, these droplets AEOI are responsible for the injector deposit in the real engine.

Abstract A three dimensional numerical model of the northwest (NW) Sabalan geothermal system was developed on the basis of the designed conceptual model from available field data. A numerical model of the reservoir was expressed with a grid system of a rectangular prism of 12 km × 8 km with 4.6 km height, giving a total area of 96 km2. The model has 14 horizontal layers ranging in thickness between 100 m to 1000 m extending from a maximum of 3600 to −1000 m a.s.l. Fifteen rock types were used in the model to assign different horizontal permeabilities from 5.0 × 10−18 to 4.0 × 10−13 m2 based on the conceptual model. Natural state modeling of the reservoir was performed, and the results indicated good agreements with measured temperature and pressure in wells. Numerical simulations were conducted for predicting reservoir performances by allocating production and reinjection wells at specified locations. Three different exploitation scenarios were examined for sustainability of reservoir for the next 30 years. Effects of reinjection location and required number of makeup wells to maintain the specified fluid production were evaluated. The results showed that reinjecting at Site B, immediate adjacent to production zone, is most effective for pressure maintenance of the system. On the base of existing data and assumptions the reservoir can sustain producing fluid equivalent to 50 MWe of electricity for more than 30 years. The reservoir can produce the maximum amount of fluids equivalent to 90–100 MWe for only 5 years, but the production capacity decreases to 50 MWe after 20 years of operation because of pressure and enthalpy drop. The reservoir can sustain 50 MWe over 100 years that can be defined as a sustainable production level of the field.

Nuclear power generation is now one of the most important technologies in the energy supply in Japan. The operational experience of nuclear power plants for more than 20 years in Japan has shown that water chemistry is a key technology for safer and more economical operation of nuclear power plants. Extensive efforts have been made in the field of water chemistry to achieve the targets of radiation field control, to keep the integrities of piping and fuel elements and to reduce the radioactive waste generation. This paper briefly describes the present status of Japanese water chemistry technology with the main emphasis placed on BWRs.

With the spotlight on smart grid development around the world, it is critical to recognize the key factors contributing to changing power system characteristics. This is more apparent in distribution systems with the integration of renewable energy sources, energy storage, and microgrid development. Utilities are also focusing on the reliability and resiliency of the grid. These activities require distribution automation (DA) strategies that take advantage of available technologies while promoting newer solutions. It is necessary to create a roadmap for holistic DA strategies in a smarter grid. Sustainable and resilient grid development is a paradigm shift requiring a new line of thinking in the engineering, operation, and maintenance of the power system. International perspectives on DA are also addressed, with the understanding that one solution will not fit all. Integrating technical, business, and policy decisions into the challenges will generate the development of technologies, standards, and implementation of the overall solution. The challenges in the development of industry standards are also discussed. This paper explores the challenges and opportunities in the changing landscape of the distribution systems. Evolution of technologies and the business case for infrastructure investment in distribution systems are covered in another paper by the same authors.

Abstract A feasibility study has been conducted to determine whether thermal plasma with steam can be used for the treatment of carbonaceous wastes such as the carbide of the hazardous wastes. The gasification of carbonaceous wastes has been especially studied to reduce their weight and the volume and to produce the synthetic gas (H2+CO). The gasification applied to this study is often called “water gas reaction (C+H2O→CO+H2)”. In this study the thermal plasma generated by the hybrid plasma system was adopted as a heat source, where steam was injected to react with carbide. Charcoal was used as a test piece instead of carbonaceous wastes. Experiments of treating charcoal were conducted by three types of thermal plasma. The result showed that the treatment of thermal plasma with steam reduced the weight of charcoal and produced hydrogen from charcoal. The thermal plasma with steam will be an attractive heat source to dispose of carbonaceous wastes.

Abstract Many organizations in the world are interested in waste management problems and their potential solutions. In order to solve these problems, a Japanese venture company has developed an innovative thermal decomposer for organic wastes called ERCM (Earth-Resource-Ceramic-Machine). The ERCM reactor employs electron injected air to promote the thermal decomposition reaction, while the effect of electron injection into air has not yet been clarified. An experimental work was performed using a fixed bed reactor to explore the effects of different parameters of electron injection into air, the reaction temperature and different feedstock on the syngas generation. The main purpose of this study is to clarify the phenomena occurring in the ERCM reactor where a direct current electric field is produced in the flame reaction zone to enhance the thermal decomposition of wastes. In this regard, a mathematical model for simulating the thermal decomposition of solid waste in the presence of an electric field have been developed. The equations of aero-thermochemistry are coupled to the balance equations for densities of charged species, and the Poisson equation for the electrical potential is solved. The model was validated by the experimental data and showed a good agreement. The results showed that the electric field significantly improves the stabilization of the flame. From the release behavior of CO and CO2, it is noted that the electron injection would affect the char combustion process significantly. Finally the effect of the flame reaction zone generated by the field induced ion wind on the thermal decomposition was investigated.

Abstract An estimation of passive cooling techniques was conducted for 14 cities in Brazil, using a fairly accurate algorithm that accounts for heat conduction, convection, radiation, and evaporation; this was done to determine the amount of heat gain/loss of room air, defined as a particular quantitative index for passive techniques. Heat gains and losses were calculated for four envelope conditions – namely, insulated, high-albedo, wet surface, and a combination of the previous two – and compared to a case assumed to be the standard condition. A conclusion drawn was that a passive design is efficient in decreasing the need for cooling in typical dwellings in Brazil; solutions should differ with regional climate characteristics. In semi-arid areas, evaporative cooling showed the best results. Reduced heat gain was found during the warm seasons for all cities, along with increased heat gain during the cool seasons for mid-latitude cities. In particular, a combination of high-albedo enveloping and evaporation can greatly decrease heat gain in building walls. High-albedo surfaces in the sub-tropical areas found in southern Brazil are more efficient. It is suggested that passive techniques should be conceived in such a way so as to work during the cooling season and be disabled during mild ones.