• Energy Research
• Closed Access close
• Embargo close
• 7. Clean energy close
• 11. Sustainability close
• DE close
• IT close
• NL close

Abstract To achieve the EU climate and energy objectives, a transition towards a future sustainable energy system is needed. The integration of the huge potential for industrial waste heat recovery into smart energy system represents a main opportunity to accomplish these goals. To successfully implement this strategy, all the several stakeholders' conflicting objectives should be considered. In this paper an evolutionary multi-objective optimization model is developed to perform a sustainability evaluation of an energy system involving an industrial facility as the waste heat source and the neighbourhood as district heating network end users. An Italian case study of heat recovery from a steel casting facility shows how the model allows to properly select the district heating network set of users to fully exploit the available waste energy. Design directions such as the thermal energy storage capacity can be also provided. Moreover, the model enables the analysis of the trade-off between the stakeholders’ different perspectives, allowing to identify possible win-win solutions for both the industrial sector and the citizenship.

Changes in the main weather features are becoming perceivable in Italy. In the last years, the average temperature and the intensity of rainstorms are increasing. Such phenomena could lead to changes in the earth-atmosphere interaction. Accounting for the high vulnerability of the Italian territory, an obvious consequence would concern the effects on the hydro-geological hazards, including landslides and floods. As a matter of fact, the higher frequency of high magnitude flood and landslide events represent an alarm bell. It is necessary to explore with all available instruments the consequences of the potential climate changes. Since quantitative predictions are not possible, the only way to run is depicting rational scenarios for the most vulnerable contexts adopting a multidisciplinary approach. Based on projections of potential climate changes in the 21st century, the report examines their potential impact in the context of the Italian peninsula. After a general overview about typical slope responses to weather changes, some quantitative scenarios have been depicted for representative geomorphological contexts. The last part of the paper examines changes in the expected risk, based on the characteristics of the Italian territory and its vulnerability, looking at the initiatives to undertake for its mitigation.

Current energy market designs and pricing schemes fail to give investors the appropriate market signals. In particular, energy prices are not high enough to attract investors to build new or maintain existing power capacity. In this paper we propose a method to compute second-best Pareto optimal equilibrium prices for any market exhibiting non-convexities and, based on this result, an energy market design able to restore the correct energy price signals for supply investors.

Direct Load Control (DLC) is an effective instrument for achieving a guaranteed load curtailment. Unfortunately, if a customer considers that personal discomfort outweighs money savings after DLC shutting down of home appliances, DLC solution can be rejected. This paper proposes the way to remediate customer comfort concerns by pre-storing additional energy in electric loads before their disconnection from the grid. We take electric tank water heaters as an illustrative example of residential loads with storage. To illuminate our approach we first show how to balance electric consumption for pre-storing with user thermal discomfort for a single water heater. Then, we illustrate how the approach can be scaled-up to a multiple-boiler scenario, when ten remotely controlled boilers act next to fifty non-controlled boilers. The simulations for the latter case show that the expected user thermal discomfort can be significantly reduced at the cost of a reasonable increase of electricity demand preceding DLC event.

Abstract Breastshot water wheels are gravity hydraulic machines employed in low head sites. The scope of this work is to test the performance of a breastshot water wheel with two geometric inflow configurations: a sluice gate at different openings and two vertical overflow weirs. With the sluice gate, the maximum efficiency of the plant is 75%, constant over a wide range of flow rates, while the efficiency with the weir is increasing in the same flow rate range. Therefore, the wheel with the weir can exploit higher water volumes, and also it performs better at high power input. In practical applications, the inflow configuration can be effectively controlled to optimize the operative working conditions of breastshot water wheels, depending on the external hydraulic ones. The experimental results are also discussed in dimensionless terms, in order to support engineers in the design of similar breastshot water wheels.

The unpredictable nature of wind energy makes its integration to the electric grid highly challenging. However, these challenges can be addressed by incorporating storage devices (batteries) in the system. We perform an overall assessment of a single domestic power system with a wind turbine supported by an energy storage device. The aim is to investigate the best operation mode of the storage device such that the occurrence of large power spills can be minimized. For estimating the small probability of large power spills, we use the splitting technique for rare-event simulations. An appropriate Importance Function for splitting is formulated such that it reduces the work-load of the probability estimator as compared to the conventional Crude Monte Carlo probability estimator. Simulation results show that the ramp constraints imposed on the charging/discharging rate of the storage device plays a pivotal role in mitigating large power spills. It is observed that by employing a new charging strategy for the storage device large power spills can be minimized further. There exists a trade-off between reducing the large power spills versus reducing the average power spills.

Abstract Hybrid energy storage is a multi-modal approach to store and supply different forms of energy (electricity, heat, cold) simultaneously. This is an important sector coupling approach and enables large scale flexibility for a deep decarbonization of energy systems. Two different proposed energy storages – power-to-heat-to-X energy storage (PHXES) and pumped thermal energy storage (PTES) – are investigated in detail in this work towards their potential towards a hybrid deployment. The techno-economic analysis includes thermodynamic flowsheet simulations and unified cost estimations based on the used equipment. It is shown that the main input data set (e.g. working fluid selection, turbomachinery efficiency, pinch temperatures) has a strong influence on storage roundtrip efficiency in the thermodynamic simulations, but also on storage costs. Cost decrease and performance increase can be conflicting development targets, and it is not clear if future energy systems rather require technologies with the highest storage efficiencies or if low cost is an important prerequisite. PHXES and three variants of PTES are implemented into a simplified energy system model of the city of Hamburg that comprises the electric load and heat demand of the district heating system. Two scenarios (fossil benchmark and 80% decarbonization) are used to select the technologies and their capacities that allow the most cost-effective energy supply solution by a linear-programming optimization procedure. Large scale renewable power generation and hybrid energy storage play the major roles in the decarbonization scenario. PHXES with a storage capacity of 69 GWh, hot water storage (3.6 GWh) and a battery system (430 MWh) are part of the cost-optimal solution. A cost sensitivity analysis shows that a total cost reduction of 60–80% is required for PTES to become competitive in this model scenario.

The crucial role evaluation can play in the co-development of project design and its implementation will be addressed through the analysis of a case study, the Green Communities (GC) project, funded by the Italian Ministry of Environment within the EU Interregional Operational Program (2007-2013) "Renewable Energy and Energy Efficiency". The project's broader goals included an attempt to trigger a change in Italian local development strategies, especially for mountain and inland areas, which would be tailored to the real needs of communities, and based on a sustainable exploitation and management of the territorial assets. The goal was not achieved, and this paper addresses the issues of how GC could have been more effective in fostering a vision of change, and which design adaptations and evaluation procedures would have allowed the project to better cope with the unexpected consequences and resistances it encountered. The conclusions drawn are that projects should be conceived, designed and carried out as dynamic systems, inclusive of a dynamic and engaged evaluation enabling the generation of feedbacks loops, iteratively interpreting the narratives and dynamics unfolding within the project, and actively monitoring the potential of various relationships among project participants for generating positive social change.

Bioplastics are alternatives of conventional petroleum-based plastics. Bioplastics are polymers processed from renewable sources and are biodegradable. This study aims at conducting an environmental impact assessment of the bioprocessing of agricultural wastes into bioplastics compared to petro-plastics using an LCA approach. Bioplastics were produced from potato peels in laboratory. In a biochemical reaction under heating, starch was extracted from peels and glycerin, vinegar and water were added with a range of different ratios, which resulted in producing different samples of bio-based plastics. Nevertheless, the environmental impact of the bioplastics production process was evaluated and compared to petro-plastics. A life cycle analysis of bioplastics produced in laboratory and petro-plastics was conducted. The results are presented in the form of global warming potential, and other environmental impacts including acidification potential, eutrophication potential, freshwater ecotoxicity potential, human toxicity potential, and ozone layer depletion of producing bioplastics are compared to petro-plastics. The results show that the greenhouse gases (GHG) emissions, through the different experiments to produce bioplastics, range between 0.354 and 0.623 kg CO2 eq. per kg bioplastic compared to 2.37 kg CO2 eq. per kg polypropylene as a petro-plastic. The results also showed that there are no significant potential effects for the bioplastics produced from potato peels on different environmental impacts in comparison with poly-β-hydroxybutyric acid and polypropylene. Thus, the bioplastics produced from agricultural wastes can be manufactured in industrial scale to reduce the dependence on petroleum-based plastics. This in turn will mitigate GHG emissions and reduce the negative environmental impacts on climate change.