• Energy Research
• engineering and technology close
• 6. Clean water close
• GB close
• DE close
• UA close

Bioplastics are alternatives of conventional petroleum-based plastics. Bioplastics are polymers processed from renewable sources and are biodegradable. This study aims at conducting an environmental impact assessment of the bioprocessing of agricultural wastes into bioplastics compared to petro-plastics using an LCA approach. Bioplastics were produced from potato peels in laboratory. In a biochemical reaction under heating, starch was extracted from peels and glycerin, vinegar and water were added with a range of different ratios, which resulted in producing different samples of bio-based plastics. Nevertheless, the environmental impact of the bioplastics production process was evaluated and compared to petro-plastics. A life cycle analysis of bioplastics produced in laboratory and petro-plastics was conducted. The results are presented in the form of global warming potential, and other environmental impacts including acidification potential, eutrophication potential, freshwater ecotoxicity potential, human toxicity potential, and ozone layer depletion of producing bioplastics are compared to petro-plastics. The results show that the greenhouse gases (GHG) emissions, through the different experiments to produce bioplastics, range between 0.354 and 0.623 kg CO2 eq. per kg bioplastic compared to 2.37 kg CO2 eq. per kg polypropylene as a petro-plastic. The results also showed that there are no significant potential effects for the bioplastics produced from potato peels on different environmental impacts in comparison with poly-β-hydroxybutyric acid and polypropylene. Thus, the bioplastics produced from agricultural wastes can be manufactured in industrial scale to reduce the dependence on petroleum-based plastics. This in turn will mitigate GHG emissions and reduce the negative environmental impacts on climate change.

Dokan reservoir is located on the Lesser Zab River NE Iraq. Its drainage area is 11,690 km2 with a storage capacity of 6.87 × 109 m3. Calculation of the volume of the reservoir before the construction of the dam and from the bathymetric survey conducted in 2014 indicates that an annual average of 7 million cubic meters of sediments are deposited within the reservoir. This reduced the storage capacity of the reservoir by 28%.

The operation of centrifugal pumps can generate instabilities and pressure pulsations that may be detrimental to the integrity and performance of the pump. In the present study a numerical investigation of the time variation of pressure within a complete centrifugal pump was undertaken. A range of parameters and three flow rates were investigated and the pulsations were extracted at 15 different locations covering important pump regions. The transient flow results compared reasonably with experimental data obtained in a limited experimental survey and clearly indicated the pump locations experiencing the largest pulsation levels. It was also noted that monitoring pulsations at the top dead centre of the pump volute casing would provide a better indication of internal pump pulsations than monitoring at the discharge.

SummaryThe German government has adopted a law that requires sewage plants to go beyond the recovery of phosphorus from wastewater and to promote recycling. We argue that there is no physical global short‐ or mid‐term phosphorus scarcity. However, we also argue that there are legitimate reasons for policies such as those of Germany, including: precaution as a way to ensure future generations’ long‐term supply security, promotion of technologies for closed‐loop economics in a promising stage of technology development, and decrease in the current supply risk with a new resource pool.

The basins of the Indus and Ganges rivers cover 2.20 million km2 and are inhabited by more than a billion people. The region is under extreme pressures of population and poverty, unregulated utilization of the resources and low levels of productivity. The needs are: (1) development policies that are regionally differentiated to ensure resource sustainability and high productivity; (2) immediate development and implementation of policies for sound groundwater management and energy use; (3) improvement of the fragile food security and to broaden its base; and (4) policy changes to address land fragmentation and improved infrastructure. Meeting these needs will help to improve productivity, reduce rural poverty and improve overall human development.

AbstractNumerous studies have been carried out to ascertain the mechanisms of low-salinity and smart water flooding technique for improved oil recovery. Focus was often on brine composition and, specifically, the cationic content in sandstone reservoirs. Given the importance of the salt composition and concentration, tweaking the active ions which are responsible for the fluids–rock equilibrium will bring into effect numerous mechanisms of displacement which have been extensively debated. This experimental study, however, was carried out to evaluate the extent of the roles of chloride- and sulphate-based brines in improved oil recovery. To carry this out, 70,000 ppm sulphates- and chloride-based brines were prepared to simulate formation water and 5000 ppm brines of the same species as low-salinity displacement fluids. Core flooding process was used to simulate the displacement of oil by using four (4) native sandstones core samples, obtained from Burgan oil field in Kuwait, at operating conditions of 1500 psig and 50 °C. The core samples were injected with 70,000 ppm chloride and sulphates and subsequently flooded with the 5000 ppm counterparts in a forced imbibition process. Separate evaluations of chloride- and sulphate-based brines were carried out to investigate the displacement efficiencies of each brine species. The results showed that in both high- and low-salinity displacement tests, the SO4 brine presented better recovery of up to 89% of the initial oil saturation (Soi). Several mechanisms of displacement were observed to be responsible for improved recovery during SO4 brine displacement. IFT measurement experiments also confirmed that there was reduction in IFT at test conditions between SO4 brine and oil and visual inspection of the effluent showed a degree emulsification of oil and brines. Changes in pH were observed in the low-salinity flooding, and negligible changes were noticed in the high-salinity floods. These results provide an insight into the roles of chloride and sulphate ions in the design of smart “designer” water and low-salinity injection scenarios.

AbstractThis paper presents the experimental plans and designs as well as examples of predictive modeling of a pilot-scale CO2 injection experiment at the Heletz site (Israel). The overall objective of the experiment is to find optimal ways to characterize CO2 -relevant in-situ medium properties, including field-scale residual and dissolution trapping, to explore ways of characterizing heterogeneity through joint analysis of different types of data, and to detect leakage. The experiment will involve two wells, an injection well and a monitoring well. Prior to the actual CO2 injection, hydraulic, thermal and tracer tests will be carried out for standard site characterization. The actual CO2 injection experiments will include (i) a single well injection-withdrawal experiment, with the main objective to estimate in-situ residual trapping and (ii) a two-well injection-withdrawal test with injection of CO2 in a dipole mode (injection of CO2 in one well with simultaneous withdrawal of water in the monitoring well), with the objective to understand the CO2 transport in heterogeneous geology as well as the associated dissolution and residual trapping. Tracers will be introduced in both experiments to further aid in detecting the development of the phase composition during CO2 transport. Geophysical monitoring will also be implemented. By means of modeling, different experimental sequences and injection/withdrawal patterns have been analyzed, as have parameter uncertainties. The objectives have been to (i) evaluate key aspects of the experimental design, (ii) to identify key parameters affecting the fate of the CO2 and (iii) to evaluate the relationships between measurable quantities and parameters of interest.

Use of a pilot-scale fixed-film bioreactor was investigated for remediation of bromate contamination within groundwater. Bromate reduction with stoichiometric production of bromide was observed, providing supporting evidence for complete reduction of bromate with no production of stable intermediates. Reduction of 87-90% bromate from an influent concentration of 1.1 mg L(-1) was observed with retention times of 40-80 h. Lower retention times led to decreases in bromate reduction capability, with 11.5% removal at a 10 h retention time. Nitrate reduction of 76-99% from a 30.7 mg L(-1) as NO(3)(-) influent was observed at retention times of 10-80 h, although an increase in nitrite production to 2.7 mg L(-1) occurred with a 10 h retention time. Backwashing was not required, with the large plastic packing media able to accommodate biomass accumulation without decreases in operational efficiency. This study has provided proof of concept and demonstrated the potential of biological bromate reduction by fixed-film processes for remediation of a bromate contaminated groundwater source.