• Energy Research
• 2016-2025close
• Closed Access close
• NL close
• UA close

The unpredictable nature of wind energy makes its integration to the electric grid highly challenging. However, these challenges can be addressed by incorporating storage devices (batteries) in the system. We perform an overall assessment of a single domestic power system with a wind turbine supported by an energy storage device. The aim is to investigate the best operation mode of the storage device such that the occurrence of large power spills can be minimized. For estimating the small probability of large power spills, we use the splitting technique for rare-event simulations. An appropriate Importance Function for splitting is formulated such that it reduces the work-load of the probability estimator as compared to the conventional Crude Monte Carlo probability estimator. Simulation results show that the ramp constraints imposed on the charging/discharging rate of the storage device plays a pivotal role in mitigating large power spills. It is observed that by employing a new charging strategy for the storage device large power spills can be minimized further. There exists a trade-off between reducing the large power spills versus reducing the average power spills.

This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No. 723649 Indoor environmental quality (IEQ) measurement and survey data of demonstration buildings in the hybridGEOTABS project

Abstract An alkaline earth boro-aluminosilicate glass (Eagle XG), a soda-lime glass, and a light-weight polyethylene-terephthalate (PET) foil, used as typical substrates for photovoltaics, were treated by an energetic proton beam (3 MeV, dose 106–107 Gy) corresponding to approx. 30 years of operation at low Earth orbit. Properties of the irradiated substrates were characterized by atomic force microscopy, optical absorption, optical diffuse reflectance, Raman spectroscopy, X-ray photoelectron spectroscopy, Fourier-transform infrared (FTIR) spectroscopy, and terahertz (THz) spectroscopy. Minimal changes of optical and morphological properties are detected on the bare Eagle XG glass, whereas the bare PET foil exhibits pronounced increase in optical absorption, generation of photoluminescence, as well as mechanical bending. On the other hand, the identical substrates coated with Indium-tin-oxide (ITO), which is a typical material for transparent electrodes in photovoltaics, exhibit significantly higher resistance to the modifications by protons while ITO structural and electronic properties remain unchanged. The experimental results are discussed considering a potential application of these materials for missions in space.

In the present study, Tween 80, a non-ionic surfactant, has been used for enhanced hydrogen production by crude glycerol bioconversion using co-culture of Enterobacter aerogenes and Clostridium butyricum. The purpose of introducing the surfactant was to decrease the crude glycerol viscosity, so that apparent solubility and bioavailability of glycerol could be improved at the expenses of pretreatment steps. Experiments were planned using central composite design (CCD); crude glycerol and Tween 80 concentrations were optimized whereas, hydrogen production, glycerol utilization and viscosity of the media were considered as responses. The response surface for quadratic model showed, Tween 80 concentration had significant effect (p < 0.05) on all the three responses. Using the optimized conditions at 17.5 g/L crude glycerol and 15 mg/L Tween 80, hydrogen production reached a maximum of 32.1 ± 0.03 mmol/L of medium. The increase in hydrogen production was around 1.25-fold in presence of Tween 80 in comparison to its absence with 25.56 ± 0.91 mmol/L production. Selected optimum conditions were also validated against absence of crude glycerol (4.69 ± 0.76), with pretreated crude glycerol (20.06 ± 0.51) and across mono-culture system (15.43 ± 0.79 to 22.14 ± 0.94). Introduction of Tween 80 to the fermentation medium improved the glycerol utilization rate, resulting in increased hydrogen production and eliminated pretreatment steps.

Grid connected energy storage systems are regarded as promising solutions for providing ancillary services to electricity networks and to play an important role in the development of smart grids. Thus far, the more mature battery technologies have been installed in pilot projects and studies have indicated their main advantages and shortcomings. The main concerns for wide adoption are the overall cost, the limited number of charging cycles (or lifetime), the depth of discharge, the low energy density and the sustainability of materials used. Vanadium Redox Flow Batteries (VRFB) are a promising option to mitigate many of these shortcomings, and demonstration projects using this technology are being implemented both in Europe and in the USA. This study presents a model using MATLAB/Simulink, to demonstrate how a VRFB based storage device can provide multi-ancillary services, focusing on frequency regulation and peak-shaving functions. The study presents a storage system at a medium voltage substation and considers a small grid load profile, originating from a residential neighbourhood and fast charging stations demand. The model also includes an inverter controller that provides a net power output from the battery system, in order to offer both services simultaneously. Simulation results show that the VRFB storage device can regulate frequency effectively due to its fast response time, while still performing peak-shaving services. VRFB potential in grid connected systems is discussed to increase awareness of decision makers, while identifying the main challenges for wider implementation of storage systems, particularly related to market structure and standardisation requirements.