• Energy Research
• US close
• GB close
• AU close
• Renewable Energy close

Abstract This study sought to quantify and characterize cassava waste as fuel. The wastes from three cultivars were collected to study and were divided into three distinct parts of the cassava plant: seed stem, thick stalks, and thin stalks. Physical and chemical analyzes were carried out to determine the elemental composition of the waste: volatile matter; fixed carbon; ash; moisture; lignin; cellulose; hemicellulose; ash composition and higher heating value were determined. We conducted a thermogravimetric analysis in oxidizing and inert atmospheres to study the behavior of the waste as fuel. The root productivity obtained ranged from 7.7 to 13.0 t ha−1 yr−1 on a dry basis (db), and the ratio between waste and roots varied from 0.36 to 0.91. The physical and chemical properties of cassava waste are analogous to those of woody biomass regarding the elemental composition, the higher heating value, and thermogravimetric analysis. Ash content varied from 2.5% to 3.5%, reaching around 6.0% in samples unwashed. Approximately 60% of the ashes are alkali oxides, especially P2O5, K2O, and CaO, which have low melting points. The alkali index calculated suggests that there is a strong tendency that the combustion process leads to ash fouling and the formation of ash deposits.

A new sizing approach is applied in this paper to stand-alone PV systems design, which is based on systems configurations without shedding load. The investigation is based on a detailed study of the minimum storage requirement and an analysis of the sizing curves. The analysis reveals the importance of using daily series of measured solar radiation data instead of monthly average values. For high-reliability systems, it is important that these data series are as long as possible, while the configuration of large generator and small battery seems to deal better with the unpredictability of solar radiation.

Abstract Bamboo has been considered a potential feedstock of energy for the future. It can be subjected to the pyrolysis for biofuels production. The thermogravimetric analysis (TGA) combined with differential thermogravimetric analysis (DTG) for bamboo was carried out prior to pyrolysis. The thermal degradation of bamboo was mainly between 230 and 420 °C. The conventional pyrolysis of bamboo was investigated in a bubbling fluidized-bed reactor using silica sand. The product distribution and composition of pyrolysis bio-oil were dependent on biomass component and operating conditions such as pyrolysis temperature, fluidization velocity, and particle size of biomass. The fractional catalytic pyrolysis of bamboo was also studied to upgrade the pyrolysis vapor, using HZSM-5 and red mud. The highest yield of bio-oil was 54.03 wt% compared to 49.14 wt% and 50.34 wt% of HZSM-5 and red mud catalyst, respectively. In the red mud catalytic pyrolysis, the oxygen content was rejected from pyrolysis vapor mostly via decarboxylation to produce more CO2 than CO; in contrast, for the HZSM-5 catalytic pyrolysis, the production of CO through decarbonylation was more favored than CO2. The main composition of catalytic pyrolysis bio-oil was 4-vinylphenol, which was employed as a raw material source to synthesize valuable material for energy storage.

Abstract In some shelf sea regions of the world, the tidal range is sufficient to convert the potential energy of the tides into electricity via tidal range power plants. As an island continent, Australia is one such region – a previous study estimated that Australia hosts up to 30% of the world’s resource. Here, we make use of a gridded tidal dataset (TPXO9) to characterize the tidal range resource of Australia. We examine the theoretical resource, and we also investigate the technical resource through 0D modelling with tidal range power plant operation. We find that the tidal range resource of Australia is 2004 TWh/yr, or about 22% of the global resource. This exceeds Australia’s total energy consumption for 2018/2019 (1721 TWh/yr), suggesting tidal range energy has the potential to make a substantial contribution to Australia’s electricity generation (265 TWh/yr in 2018/2019). Due to local resonance, the resource is concentrated in the sparsely populated Kimberley region of Western Australia. However, the tidal range resource in this region presents a renewable energy export opportunity, connecting to markets in southeast Asia. Combining the electricity from two complementary sites, with some degree of optimization tidal range schemes in this region can produce electricity for 45% of the year.

Abstract This paper investigates the hydrodynamics of a seabed-mounted, bottom-hinged, flap-type wave energy converter in shallow water. A conceptual model of the hydrodynamics of the device has been formulated and shows that, as the motion of the flap is highly constrained, the magnitude of the wave force on the flap is the key determinant of power capture. The results from a physical modelling program have been used in conjunction with numerical data from WAMIT to validate the conceptual model. The work finds that designing the device to increase the wave force is more profitable than designing it to be tuned to the incident wave climate. As wave force is the primary driver of device performance it is shown that the flap should fill the water column and pierce the water surface to reduce decoupling due to wave overtopping. It is concluded that, in order to maximize capture factor at a typical North Atlantic site, the flap should be approximately 20–30 m wide, with large diameter rounded side edges, having its pivot close to the seabed and its top edge piercing the water surface.

Abstract To address the problem of fossil fuel usage at the Missouri University of Science and Technology campus, using of alternative fuels and renewable energy sources can lower energy consumption and hydrogen use. Biogas, produced by anaerobic digestion of wastewater, organic waste, agricultural waste, industrial waste, and animal by-products is a potential source of renewable energy. In this work, we have discussed Hydrogen production and End-Uses from CHHP system for the campus using local resources. Following the resource assessment study, the team selects FuelCell Energy DFC1500™ unit as a molten carbonate fuel cell to study of combined heat, hydrogen and power (CHHP) system based on a molten carbonate fuel cell fed by biogas produced by anaerobic digestion. The CHHP system provides approximately 650 kg/day. The total hydrogen usage 123 kg/day on the university campus including personal transportation applications, backup power applications, portable power applications, and other mobility applications are 56, 16, 29, 17, and 5 respectively. The excess hydrogen could be sold to a gas retailer. In conclusion, the CHHP system will be able to reduce fossil fuel usage, greenhouse gas emissions and hydrogen generated is used to power different applications on the university campus.

We tested this system with objectives to plan and apply this system in Japan, and examined its cooling effectiveness and ir flow generation

Abstract A huge inrush of PHEVs is envisioned in the future. There is a growing risk that, this proliferation in the number of PHEVs will trigger extreme surges in demand while charging them during rush hours. To mitigate this impact, a smart charging station is proposed in which the charging of the PHEVs is controlled in such a way that the impact of charging during peak load period is not felt on the grid. The power needed to charge the plug in hybrids comes from grid-connected photovoltaic generation or the utility or both. The three way interaction between the PV, PHEVs and the grid ensures optimal usage of available power, charging time and grid stability. The system designed to achieve the desired objective consists of a photovoltaic system, DC/DC boost converter, DC/AC bi-directional converter and DC/DC buck converter. The output of DC/DC boost converter and input of DC/AC bi-directional converter share a common DC link. A unique control strategy based on DC link voltage sensing is proposed for the above system for efficient transfer of energy.

Abstract Sweet sorghum, a C4 plant, is known to be a unique, versatile, and potential energy crop that can be separated into starchy grains, soluble sugar juice, and lignocellulosic biomass. The fermentable sugars in the juice (53–85% sucrose, 9–33% glucose, and 6–21% fructose) can be directly fermented into ethanol. The grain is primarily starch (62–75%), which can be hydrolyzed and fermented into ethanol. The bagasse, a fibrous lignocellulosic material, can be used to produce cellulosic ethanol, heat and/or power co-generation. In this review, the potential of sweet sorghum for bioenergy production (of various forms) using recently developed cultivars with improved agronomic performance was discussed. In addition, sweet sorghum was compared with other starch, sugar, and lignocellulosic feedstocks. Studies have been conducted on alternative pathways to convert whole sweet sorghum stalks and bagasse into bioenergy. However, very little review of the techno-economic analysis of bioenergy production and co-products from sweet sorghum has been published. The aim of this research was to review the current knowledge of agronomic requirement for cultivating sweet sorghum, the productivity of recently developed cultivars for bioenergy production, and pathways of converting sweet sorghum crop into bioenergy as well as the techno-economic feasibility of using sweet sorghum for bioenergy.