• Energy Research
• other engineering and technologies close
• 6. Clean water close
• CN close
• US close
• GB close

This paper presents an analysis of the problem of reorientation of a riser pipe from an initially horizontal configuration during subsurface tow to the vertical position for installation. Front and rear barges support the pipe through cables. The orientation into a vertical configuration is accomplished by paying out the front cable. The pipe is treated as a Bernoulli-Euler beam with significant tension undergoing large angle deflections. A finite element procedure used state transfer matrices and successive linearization and the results show that the stress critical phase occurs when the pipe is going through the 60-deg angle to the horizontal direction.

Microwave-assisted alkali pre-treatment of wheat straw and its enzymatic hydrolysis were investigated and compared with the conventional alkali pre-treatment process. First, the effect of microwave power and pre-treatment time on the weight loss and composition of wheat straw was examined. The results show that the higher microwave power with shorter pre-treatment time and the lower microwave power with longer pre-treatment time had the same effect on the weight loss and composition at the same energy consumption. The comparison was then made between the effect of the microwave-assisted alkali pre-treatment and the conventional alkali one on the weight loss and composition of wheat straw. The wheat straw had a weight loss of 48·4% and a composition of cellulose 79·6%, lignin 5·7% and hemicellulose 7·8% after 25 min microwave-assisted alkali pre-treatment at 700 W, compared with a weight loss of 44·7% and a composition of cellulose 73·5%, lignin 7·2% and hemicellulose 11·2% after 60 min conventional alkali pre-treatment. The microwave-assisted alkali pre-treatment removed more lignin and hemicellulose from wheat straw with shorter pre-treatment time compared with the conventional alkali one. Finally, the enzymatic hydrolysis of pre-treated wheat straw (substrate concentration 50 g l−1, enzyme loading 20 mg g−1 substrate) was also investigated and the results indicate that the microwave-assisted alkali pre-treated wheat straw had higher hydrolysis rate, reducing sugar concentration and glucose content in the hydrolysate than the conventional alkali pre-treated one. Microwave-assisted alkali pre-treatment is a potential alternative of wheat straw pre-treatment for its enzymatic hydrolysis.

Abstract Microorganisms used in syngas fermentation require nutrients to grow and convert syngas (CO, H2 and CO2) into various products. Many of the essential nutrients can be provided by biochar. Poultry litter biochar (PLBC) contains minerals and trace metals and has a high pH buffering capacity, making it suitable as a nutrient supplement. The effects of PLBC loadings from 1 to 20 g L−1 on syngas fermentation were determined in 250 ml bottle assays. Results showed that 10 and 20 g L−1 PLBC significantly increased ethanol production compared to standard yeast extract (YE) medium. Fermentations in a 3L continuous stirred tank reactor (CSTR) with 10 g L−1 PLBC with and without 4-morpholineethanesulfonic acid (MES) showed 64% and 36% more ethanol production, respectively, than standard medium. The acetic acid accumulated at the beginning of fermentation was completely converted to ethanol in all media tested in the CSTR. These results demonstrate the feasibility of using PLBC medium without costly MES in the CSTR to enhance ethanol production from syngas for potential use at commercial scale.

In the water-rich karst regions, high water and mud outbursts are common geological disasters in tunnel construction. To ensure the safe and smooth construction of tunnel projects, it is necessary to consider anti-water pressure, water inrush prevention and geological disasters during the design of tunnels. Based on the Yongfutun Tunnel Project, this paper studies the application and effect of radial grouting and curtain grouting, which involves those in high-water-pressure tunnels under double-layer support conditions. To obtain the effects and parameters of radial grouting and curtain grouting, the influences of different grouting ranges on the tunnel’s surrounding rocks and supporting structures were analyzed and the finite difference method was adopted. The results show that the radial grouting of the surrounding rock can notably improve the initial support of the tunnel, but the impact is less obvious when the grouting range exceeds 4 m. The design of radial grouting is recommended to be 4.0 m to 4.5 m. Curtain grouting can effectively reduce the external water pressure of the tunnel lining. The external water pressure of the grouting area is 23% greater than that without curtain grouting. Curtain grouting can slow down the infiltration of external water pressure. This is beneficial to the stress of the tunnel lining structure, but the improvement in initial support force is slight. Moreover, curtain grouting improves the safety reserve of the secondary lining by strengthening the self-stability ability of the surrounding rock. Meanwhile, the double-layer primary support can effectively share the external water pressure and surrounding rock pressure. This study provides a certain reference for the lining design of high-water-pressure tunnels.

Abstract In this paper, coupled governing equations were proposed to simulate three-dimensional heat conduction and moisture transport in the nuclear waste repository. Because there will be a large temperature gradient near inner and outer boundaries of the bentonite buffer layer, and the heat driven moisture transport is introduced in the governing equation of moisture transport. By applying the Fourier and Laplace transforms, the governing equations were converted to the Bessel equations, and the Laplace-domain solutions to temperature and moisture distributions were derived through the inverse Fourier transform. The reliability of the proposed solutions was verified through comparative analysis with the line heat source model. These analytical solutions were applied to obtain the evolutions of temperature field and moisture distribution near the waste canister. Finally, a sensitivity study was performed to analyze the effects of relevant parameters on the heat driven moisture transport.

Energy is consumed at every stage of the cycle of water production, distribution, end use, and recycled water treatment. Understanding the nexus of energy and water may help to minimize energy and water consumption and reduce environmental emissions. However, the interlinkages between water and energy have not received adequate attention. To address this gap, this paper disaggregates and quantifies the energy consumption of the entire water cycle process in Beijing. The results of this study show that total energy consumption by water production, treatment and distribution, end use, and recycled water reuse amounts to 55.6 billion kWh of electricity in 2015, or about 33% of the total urban energy usage. While water supply amount increased by only 10% from 2005 to 2015, the related energy consumption increased by 215% due to water supply structural change. The Beijing municipal government plans to implement many water saving measures in the area from 2016 to 2020, however, these policies will increase energy consumption by 74 million kWh in Beijing. This study responds to the urgent need for research on the synergies between energy and water. In order to achieve the goal of low-energy water utilization in the future, water and energy should be integrated in planning and management.

Abstract CBM reservoirs are extremely vulnerable to damage due to their complex pore structure. So, changing pore structures in CBM reservoirs is of vital importance for reducing reservoirs damage. Organic solvents have been considered as additives into fracturing fluids to enhance production because they can enhance the pore connectivity and loosening macromolecular network structure. It is thus of great interests to investigate how organic solvents (ethanol and ethylene glycol ether) change micropore structures and fluid distribution. In this study, samples were selected from different wells completed in No. 3 coal seam, Zhaozhuang minefield. Low-pressure nitrogen adsorption (LP-N2GA) experiments were conducted on coal samples to evaluate the changes in pore-structure parameters including specific surface area (SSA), pore diameter, and pore volume. NMR experiments were conducted on coal samples to evaluate the changes in fluid distribution. Analyzing the LP-N2GA results suggests ethylene glycol ether and ethanol can effectively increase SSA, pore diameter, and opening degree of pores in coal samples. Comparative analysis of NMR results indicates that ethylene glycol ether consistently reduces the irreducible water saturation (Swir) in samples. The average value of Swir of raw samples is 0.8670 and the average value of Swir of samples treated with ethylene glycol ether value is 0.7644. Considering the pore-structure alterations, this study demonstrates that ethylene glycol ether is more preferable for enhancing recovery from CBM reservoirs compared with ethanol.

As a porous medium with rich pore structure, activated carbon (AC) was once considered the best carrier for hydrate storage and transportation. However, the harsh conditions of the hydrate reaction in the wet carbon environment have always limited the sufficient and rapid formation of hydrate. Therefore, the influences of particle size (4–8, 8–16, 20–40 and 100 mesh) and liquid phase saturation (fully/partially saturated) in the sodium dodecyl sulfate system on hydrate reaction were investigated. The results showed that small particle in the fully saturated liquid phase system led to the increase in hydrate generation rate, with the highest hydrate reaction rate of 3.16 mmol/min in the 100 mesh AC layer, which was 1.7–2.9 times higher than other AC layers. The gas storage capability of the 4–8 mesh AC layer with a water saturation of 70% was the highest among all systems, reaching 0.198 mol/mol. The saturation of the liquid phase induced the nucleation and growth of hydrates. Adherently growing hydrates of fully saturated liquid phase systems and mushroom-like hydrates of partially saturated liquid phase systems were found in turn. This research facilitates the commercialization of AC-based hydrate technology.

AbstractThe integration of power plants and desalination systems has attracted increasing attention over the past few years as an effective solution to tackle sustainable development and climate change issues. In this light, this paper introduces a novel modelling and optimization approach for a combined-cycle power plant (CCPP) integrated with reverse osmosis (RO) and multi-effect distillation (MED) desalination systems. The integrated CCPP and RO–MED desalination system is thermodynamically modelled utilizing MATLAB and EES software environments, and the results are validated via Thermoflex software simulations. Comprehensive energy, exergic, exergoeconomic, and exergoenvironmental (4E) analyses are performed to assess the performance of the integrated system. Furthermore, a new multi-objective water cycle algorithm (MOWCA) is implemented to optimize the main performance parameters of the integrated system. Finally, a real-world case study is performed based on Iran's Shahid Salimi Neka power plant. The results reveal that the system exergy efficiency is increased from 8.4 to 51.1% through the proposed MOWCA approach, and the energy and freshwater costs are reduced by 8.4% and 29.4%, respectively. The latter results correspond to an environmental impact reduction of 14.2% and 33.5%. Hence, the objective functions are improved from all exergic, exergoeconomic, and exergoenvironmental perspectives, proving the approach to be a valuable tool towards implementing more sustainable combined power plants and desalination systems.

A promising route to transition wastewater treatment facilities (WWTFs) from energy-consuming to net energy-positive is to retrofit existing facilities with process modifications, residual biosolid upcycling, and effluent thermal energy recovery. This study assesses the economics and life cycle environmental impacts of three proposed retrofits of WWTFs that consider thermochemical conversion technologies, namely, hydrothermal liquefaction, slow pyrolysis, and fast pyrolysis, along with advanced bioreactors. The results are in turn compared to the reference design, showing the retrofitting design with hydrothermal liquefaction, and an up-flow anaerobic sludge blanket has the highest net present value (NPV) of $177.36MM over a 20-year plant lifetime despite 15% higher annual production costs than the reference design. According to the ReCiPe method, chlorination is identified as the major contributor for most impact categories in all cases. There are several uncertainties embedded in the techno-economic analysis and life cycle assessment, including the discount rate, capital investment, sewer rate, and prices of main products; among which, the price of biochar presents the widest variation from $50 to $1900/t. Sensitivity analyses reveal that the variation of discount rates causes the most significant changes in NPVs. The impact of the biochar price is more pronounced in the slow pyrolysis-based pathway compared to the fast pyrolysis since biochar is the main product of slow pyrolysis.