• Energy Research
• other engineering and technologies close
• US close
• GB close
• DE close

The path congestion and communication risks of electric power communication network have emerged as the carried businesses are becoming more and more heavy. In this paper, a multi-objective optimization method for power communication network routing considering the importance of the carried businesses is proposed to reduce load imbalance and transmission risk. Firstly, information entropy is introduced as the objective of communication network load balancing optimization. And a risk assessment model for power communication network nodes and links is established. Then fuzzy membership functions are adopted to singularize the two objectives to jointly optimize path congestion and communication risks. The device nodes are dynamically divided according to the carried businesses to pursue the global optimization of the power communication network in which the Yen's algorithm is adopted. Finally, this paper uses the IEEE 30-bus communication network to carry out case simulations and analyzes the proposed method to verify the effectiveness and feasibility.

Wind characteristics (e.g., mean wind speed, gust factor, turbulence intensity and integral scale, etc.) are quite scattered in different measurement conditions, especially during typhoon and/or hurricane processes, which results in the structural engineer ambiguously determining the wind parameters in wind-resistant design of buildings and structures in cyclone-prone regions. In tropical cyclones (including typhoons and hurricanes), the inconsistent wind characteristics may be in part ascribed to the complex flow structure with the coexistence of both mechanical and convective turbulence in the boundary layer of tropical cyclones. Another significant contribution to the scattered wind characteristics is due to various measurement conditions (e.g., terrain exposure and height) and data processing schemes (e.g., averaging time). The removal of the inconsistency in the field-measurement system may offer a more rational comparison of measured wind data from various observation platforms, and hence facilitates a better identification scheme of the wind characteristics to guide the urban planning design and wind-resistant design of buildings and structures. In this study, an analytical framework was firstly proposed to eliminate the potential observation-related effects in wind characteristics and then the wind characteristics of seven field measured tropical cyclones (four typhoons and three hurricanes) were comparatively investigated. Specifically, field measurements of wind characteristics were converted to a standard reference station with a roughness length of 0.03 m, observation duration of 10 min for mean wind and averaging time of 3 s for gusty wind at a 10 m height. The differences of the measured wind characteristics between the typhoons and hurricanes were highlighted. The standardized turbulent wind characteristics under the analytical framework for typhoons and hurricanes were compared with the corresponding recommendations in standard of American Society of Civil Engineers (ASCE 7-10) and Architectural Institute of Japan Recommendations for Loads on Buildings (AIJ-RLB-2004).

This paper presents an analysis of the problem of reorientation of a riser pipe from an initially horizontal configuration during subsurface tow to the vertical position for installation. Front and rear barges support the pipe through cables. The orientation into a vertical configuration is accomplished by paying out the front cable. The pipe is treated as a Bernoulli-Euler beam with significant tension undergoing large angle deflections. A finite element procedure used state transfer matrices and successive linearization and the results show that the stress critical phase occurs when the pipe is going through the 60-deg angle to the horizontal direction.

Particle receivers are gaining importance in the field of Concentrating Solar Power (CSP) due to the high temperature that particles can achieve without degradation. Several researchers are studying the potential of this technology by means of system analyses, which need simple and light models of the system. This study presents two simple models for the particle receiver. The simplest model is a correlation obtained by fitting the results calculated with a more complex receiver model simulated in CFD. The other model is a 1D model, which is benchmarked against the same CFD results. Although both models achieve high coefficient of determination, R2, when compared to CFD results, the 1D model seems to provide more accurate results (especially during sunsets and sunrises). Both models are integrated into a tecno-economic model developed in previous work. The LCOE obtained with the 1D model is between 7% and 10% greater than the one obtained with the correlation.

A method is presented for calculating the electromagnetic forces on the end windings of turbine generators for both the steady state and transient modes of operation. Part 1 of this paper deals with the basic concepts of the force calculation and gives several examples of steady state forces and how they vary with load and power factor. PartII deals with several types of transient operation. The currents and fields which these transients produce are discussed and forces are found for various cases such as short circuits, synchronizing out of phase and transmission line switching.

Abstract Secondary concentrators are used in solar concentrating systems to redirect solar beams reflected by the primary concentrators to the focal point or line. These components allow to increase the concentrated solar flux density and hence to lower thermal radiation losses. Solar reflectors for secondary concentrators are permanently exposed to environmental conditions, high radiation fluxes and elevated temperatures that potentially cause stress and degradation throughout the time. Therefore, analyzing solar reflectors of secondary concentrators by simulating these conditions is crucial. No previous research works about the durability of solar reflector materials for secondary concentrators have been reported. The present work is focused on studying the degradation of the reflector materials by simulating accelerated aging, caused by several ambient parameters and the effect of concentrated radiation. Both cooled and uncooled systems for secondary concentrators are included in this study. According to results obtained, aluminum reflectors and thin silvered-glass reflectors glued to an aluminum structure showed minimum reflectance losses and structural degradation under the operation conditions of cooled 3D secondary concentrators (tower systems). Following critical aspects to avoid reflector degradation were identified: to select a suitable adhesive material to glue the thin silvered-glass reflector to the support aluminum structure, to properly protect reflectors edges, to design a suitable cooling system and to avoid the combination of high radiation fluxes with mechanical stress. In addition, laminated silvered-glass reflectors have shown to be suitable for uncooled 2D secondary concentrators (Fresnel collectors). Furthermore, a comparison with naturally aged secondary concentrators using silvered-glass reflectors glued to an aluminum structure revealed that the simulated degradation under accelerated conditions performed in this work did reproduce the most frequent degradation patterns suffered in real operating conditions.

This paper introduces a model predictive control (MPC) strategy for the purpose of fuel-optimal operation of a range-extender hybrid vehicle. The modern navigation system nowadays can provide abundant road information. Using this information, the proposed controller solves a global optimization problem offline in order to determine a preset trajectory of the state of charge (SoC). The online MPC uses the resulting SoC trajectory as set-points for the terminal state in every moving horizon. Repeating this process, the optimal energy management along the trip to be traveled can thus be calculated. This proposed control strategy is implemented in the commercial vehicle simulation environment IPG CarMaker. From the first simulation results, the proposed strategy shows a promising fuel saving potential with real-time capability.

The most severe failures in power grids are often characterized as cascading failures where an initial event triggers consequent failures all along the grid often leading to blackouts. Upon identifying a failure and its cascade potential, timely control actions should be performed by the grid operators to mitigate the effect of the cascade. These actions have to be delivered to one or more control devices, creating a dependency between the power grid and its control network. This paper examines the dependency of the operation of the power grid on the control network. Different from literature studies on failure control, our dependency model captures the impact of networking parameters. We formulate an algorithmic model that describes the impact of this dependency on cascade control. Based on this model, we propose an efficient cascade control algorithm using load shedding with consideration of delays in the communication network for power grids. Finally, we evaluate the impact of the power-communication network dependency with uncontrolled grids, ideal/simple control grids and our proposed control scheme. The results demonstrate that the proposed algorithm can significantly reduce the failure of power lines while sustaining larger power demand for users.

AbstractIn this paper a complete vehicle system simulation tool chain which applies a Multi Objective Optimization (MOO) methodology for designing the Electric Powertrain (ePT) of Battery Electric Vehicles (BEV) is presented. Optimization scope includes all relevant electric powertrain components from battery, inverter, electric machine to gear box. In addition to cost, vehicle dynamics, energy consumption and range are further optimization targets. For an overall minimal system cost design a multiplicity of interactions between all powertrain components has to be taken into account. High system complexity prevents an expert to consider all relevant correlations without the support of numeric simulation tools. The presented simulation tool chain enables fast identification of the best cost/benefit trade off regarding system cost while considering all defined system performance requirements. The approach enables experts to find unconventional solutions which would have been overlooked applying a classical straight forward approach and, thus, helps to sharpen the expert's knowledge in cause-effect relationships on the system level. Typical use cases are given and illustrated by several practical examples.