• Energy Research
• 7. Clean energy close
• 11. Sustainability close
• 2. Zero hunger close
• US close
• DE close
• NL close

The operation of a building connects the building, its performance and its end-users. When a mismatch occurs between users' expectations and operations processes, then complaints can arise. The use of enhanced complaint handling processes is investigated to ascertain whether this can help diagnose performance problems. Two LEED Platinum-rated office buildings form the basis for a case study of the components that make up an enhanced complaint handling process. Some of the social dynamics of complaints in buildings are consequently discussed. It is found that an enhanced complaint handling approach could contribute to a form of ongoing commissioning that goes beyond primarily reactive or dismissive treatments of complaints. Le fonctionnement d'un immeuble etablit des rapports entre l'immeuble, ses performances et ses utilisateurs finaux. Lorsqu'un decalage se produit entre les attentes des utilisateurs et les processus d'exploitation, des plaintes peuvent alors s'elever. L'utilisation de processus ameliore...

Global wind resources greatly exceed current electricity demand and the levelized cost of energy from wind turbines has shown precipitous declines. Accordingly, the installed capacity of wind turbines grew at an annualized rate of about 14% during the last two decades and wind turbines now provide ~6–7% of the global electricity supply. This renewable electricity generation source is thus already playing a role in reducing greenhouse gas emissions from the energy sector. Here we document trends within the industry, examine projections of future installed capacity increases and compute the associated climate change mitigation potential at the global and regional levels. Key countries (the USA, UK and China) and regions (e.g., EU27) have developed ambitious plans to expand wind energy penetration as core aspects of their net-zero emissions strategies. The projected climate change mitigation from wind energy by 2100 ranges from 0.3–0.8 °C depending on the precise socio-economic pathway and wind energy expansion scenario followed. The rapid expansion of annual increments to wind energy installed capacity by approximately two times current rates can greatly delay the passing of the 2 °C warming threshold relative to pre-industrial levels. To achieve the required expansion of this cost-effective, low-carbon energy source, there is a need for electrification of the energy system and for expansion of manufacturing and installation capacity.

Parabolic trough power plants are currently the most commercially applied systems for CSP power generation. To improve their cost-effectiveness, one focus of industry and research is the development of processes with other heat transfer fluids than the currently used synthetic oil. One option is the utilization of water/steam in the solar field, the so-called direct steam generation (DSG). Several previous studies promoted the economic potential of DSG technology [1–3]. Analyses’ results showed that live steam parameters of up to 500°C and 120 bars are most promising and could lead to a reduction of the levelized electricity cost (LEC) of about 11% [4]. However, all of these studies only considered plants without thermal energy storage (TES). Therefore, a system analysis including integrated TES was performed by Flagsol GmbH and DLR together with Solar Millennium AG, Schott CSP GmbH and Senior Bergho¨fer GmbH, all Germany. Two types of plants are analyzed and compared in detail: a power plant with synthetic oil and a DSG power plant. The design of the synthetic oil plant is very similar to the Spanish Andasol plants [5] and includes a molten salt two-tank storage system. The DSG plant has main steam parameters of 500 °C and 112 bars and uses phase change material (PCM) for the latent and molten salt for the sensible part of the TES system. To enable comparability, both plants share the same gross electric turbine capacity of 100 MWel, the same TES capacity of nine hours of full load equivalent and the same solar multiple of the collector field of about two. This paper describes and compares both plants’ design, performance and investment. Based on these results, the LEC are calculated and the DSG plant’s potential is evaluated. One key finding is that with currently proposed DSG storage costs, the LEC of a DSG plant could be higher than those of a synthetic oil plant. When considering a plant without TES on the other hand, the DSG system could reduce the LEC. This underlines the large influence of TES and the still needed effort in the development of a commercial storage system for DSG.

The industrial sector accounts for 17% of end-use energy in the UK, and 54% globally. Therefore, there is substantial scope for simulating and assessing potential energy retrofit options for industrial buildings. Building Energy Modelling (BEM) applied to industrial buildings poses a complex but important opportunity for reducing global energy demand, due to years of renovation and expansion. Large and complex industrial buildings make modelling existing geometry for BEM difficult and time consuming. This paper presents a potential solution for quickly capturing and processing as-built geometry of a factory to be utilized in BEM. Laser scans were captured from the interior of an industrial facility to produce a Point Cloud. The existing capabilities of a Point Cloud processing software were assessed to identify the potential development opportunities to automate the conversion of Point Clouds to building geometry for BEM applications. In conclusion, scope exists for increasing the speed of 3D geometry creation of an existing industrial building for application in BEM and subsequent thermal simulation.

DOE-2 (DOE2 90) includes several correlation curves that predict the energy use of systems underpart load conditions. DOE-2 simulates systems on an hour-by-hour basis, so the correlations are intended to predict part load energy use (and efficiency) as a function of the part load ratio (PLR) for each hour, where PLR = Hourly Load/Available Capacity. Generally residential and small commercial HVAC equipment meets the load at off-design conditions by cycling on and off. Therefore, the part load correlations must predict the degradation due to this on and off operation over an hourly interval.

AbstractThe Controlled Freeze Zone™ technology removes CO2 and H2S from natural gas in a single step cryogenic distillation process. Removal and management of acid gas impurities from natural gas pose significant challenges in developing sour gas fields. In many cases CFZ™ is capable of processing sour gases with a wide range of CO2 and H2S compositions at a lower cost than conventional technologies. The acidic components are removed as a high pressure liquid that can be injected into reservoirs for geosequestration or, when of suitable composition, to improve oil recovery. In either case, sulfur production from H2S and release of CO2 to the atmosphere can be eliminated.CFZ™ technology was successfully demonstrated through earlier pilot plant operations. Currently, ExxonMobil Upstream Research Company is advancing CFZ™ to large scale commercial readiness through a commercial demonstration plant in Wyoming, USA. By building the commercial demonstration plant at ExxonMobil’s world-class Shute Creek gas treating and acid gas injection facility, integration of CFZ™ with acid gas injection, will also be demonstrated when the unit is operated in 2010–2011.

AbstractA novel multifunctional conjugated polymer (RCP‐1) composed of an electron‐donating backbone (carbazole) and an electron‐accepting side chain (cyanoacetic acid) connected through conjugated vinylene and terthiophene has been synthesized and tested as a photosensitizer in two major molecule‐based solar cells, namely dye sensitized solar cells (DSSCs) and organic photovoltaic cells (OPVs). Promising initial results on overall power conversion efficiencies of 4.11% and 1.04% are obtained from the basic structure of DSSCs and OPVs based on RCP‐1, respectively. The well‐defined donor (D)‐acceptor (A) structure of RCP‐1 has made it possible, for the first time, to reach over 4% of power conversion efficiency in DSSCs with an organic polymer sensitizer and good operation stability.