• Energy Research
• engineering and technology close
• US close
• GB close
• DE close
• AU close

The Intergovernmental Panel on Climate Change (IPCC) report that to limit warming to 1.5 °C, Bioenergy with Carbon Capture and Storage (BECCS) is required. Integrated assessment models (IAMS) predict that a land area between the size of Argentina and Australia is required for bioenergy crops, a 3–7 time increase in the current bioenergy planting area globally. The authors pose the question of whether vertical farming (VF) technology can enable BECCS deployment, either via land sparing or supply. VF involves indoor controlled environment cultivation, and can increase productivity per unit land area by 5–10 times. VF is predominantly being used to grow small, high value leafy greens with rapid growth cycles. Capital expenditure, operational expenditure, and sustainability are challenges in current VF industries, and will affect the ability to utilise this technology for other crops. The authors argue that, whilst challenging, VF could help reach wider climate goals. Application of VF for bioenergy crops could be a game changer in delivering BECCS technologies and may reduce the land footprint required as well as the subsequent associated negative environmental impacts. VF bioenergy could allow us to cultivate the future demand for bioenergy for BECCS on the same, or less, land area than is currently used globally.

The path congestion and communication risks of electric power communication network have emerged as the carried businesses are becoming more and more heavy. In this paper, a multi-objective optimization method for power communication network routing considering the importance of the carried businesses is proposed to reduce load imbalance and transmission risk. Firstly, information entropy is introduced as the objective of communication network load balancing optimization. And a risk assessment model for power communication network nodes and links is established. Then fuzzy membership functions are adopted to singularize the two objectives to jointly optimize path congestion and communication risks. The device nodes are dynamically divided according to the carried businesses to pursue the global optimization of the power communication network in which the Yen's algorithm is adopted. Finally, this paper uses the IEEE 30-bus communication network to carry out case simulations and analyzes the proposed method to verify the effectiveness and feasibility.

In this paper, we study the interactions among interconnected autonomous microgrids, and propose a joint energy trading and scheduling strategy. Each interconnected microgrid not only schedules its local power supply and demand, but also trades energy with other microgrids in a distribution network. Specifically, microgrids with excessive renewable generations can trade with other microgrids in deficit of power supplies for mutual benefits. Since interconnected microgrids operate autonomously, they aim to optimize their own performance and expect to gain benefits through energy trading. We design an incentive mechanism using Nash bargaining theory to encourage proactive energy trading and fair benefit sharing. We solve the bargaining problem by decomposing it into two sequential problems on social cost minimization and trading benefit sharing, respectively. For practical implementation, we propose a decentralized solution method with minimum information exchange overhead. Numerical studies based on realistic data demonstrate that the total cost of the interconnected-microgrids operation can be reduced by up to 13.2% through energy trading, and an individual participating microgrid can achieve up to 29.4% reduction in its cost through energy trading. To appear in IEEE Transactions on Smart Grid

Wind characteristics (e.g., mean wind speed, gust factor, turbulence intensity and integral scale, etc.) are quite scattered in different measurement conditions, especially during typhoon and/or hurricane processes, which results in the structural engineer ambiguously determining the wind parameters in wind-resistant design of buildings and structures in cyclone-prone regions. In tropical cyclones (including typhoons and hurricanes), the inconsistent wind characteristics may be in part ascribed to the complex flow structure with the coexistence of both mechanical and convective turbulence in the boundary layer of tropical cyclones. Another significant contribution to the scattered wind characteristics is due to various measurement conditions (e.g., terrain exposure and height) and data processing schemes (e.g., averaging time). The removal of the inconsistency in the field-measurement system may offer a more rational comparison of measured wind data from various observation platforms, and hence facilitates a better identification scheme of the wind characteristics to guide the urban planning design and wind-resistant design of buildings and structures. In this study, an analytical framework was firstly proposed to eliminate the potential observation-related effects in wind characteristics and then the wind characteristics of seven field measured tropical cyclones (four typhoons and three hurricanes) were comparatively investigated. Specifically, field measurements of wind characteristics were converted to a standard reference station with a roughness length of 0.03 m, observation duration of 10 min for mean wind and averaging time of 3 s for gusty wind at a 10 m height. The differences of the measured wind characteristics between the typhoons and hurricanes were highlighted. The standardized turbulent wind characteristics under the analytical framework for typhoons and hurricanes were compared with the corresponding recommendations in standard of American Society of Civil Engineers (ASCE 7-10) and Architectural Institute of Japan Recommendations for Loads on Buildings (AIJ-RLB-2004).

Abstract With the rapid advancement in wearable electronics, energy harvesting devices based on triboelectric nanogenerators (TENGs) have been intensively investigated for providing sustainable power supply for them. However, the fabrication of wearable TENGs still remains great challenges, such as flexibility, breathability and washability. Here, a route to develop a new kind of woven-structured triboelectric nanogenerator (WS-TENG) with a facile, low-cost, and scalable electrospinning technique is reported. The WS-TENG is fabricated with commercial stainless-steel yarns wrapped by electrospun polyamide 66 nanofiber and poly(vinylidenefluoride-co-trifluoroethylene) nanofiber, respectively. Triggered by diversified friction materials under a working principle of freestanding mode, the open-circuit voltage, short-circuit current and maximum instantaneous power density from the WS-TENG can reach up to 166 V, 8.5 µA and 93 mW/m2, respectively. By virtue of high flexibility, desirable breathability, washability and excellent durability, the fabricated WS-TENG is demonstrated to be a reliable power textile to light up 58 light-emitting diodes (LED) connected serially, charge commercial capacitors and drive portable electronics. A smart glove with stitched WS-TENGs is made to detect finger motion in different circumstances. The work presents a new approach for self-powered textiles with potential applications in biomechanical energy harvesting, wearable electronics and human motion monitoring.

This paper presents an analysis of the problem of reorientation of a riser pipe from an initially horizontal configuration during subsurface tow to the vertical position for installation. Front and rear barges support the pipe through cables. The orientation into a vertical configuration is accomplished by paying out the front cable. The pipe is treated as a Bernoulli-Euler beam with significant tension undergoing large angle deflections. A finite element procedure used state transfer matrices and successive linearization and the results show that the stress critical phase occurs when the pipe is going through the 60-deg angle to the horizontal direction.

A method is presented for calculating the electromagnetic forces on the end windings of turbine generators for both the steady state and transient modes of operation. Part 1 of this paper deals with the basic concepts of the force calculation and gives several examples of steady state forces and how they vary with load and power factor. PartII deals with several types of transient operation. The currents and fields which these transients produce are discussed and forces are found for various cases such as short circuits, synchronizing out of phase and transmission line switching.

Abstract Secondary concentrators are used in solar concentrating systems to redirect solar beams reflected by the primary concentrators to the focal point or line. These components allow to increase the concentrated solar flux density and hence to lower thermal radiation losses. Solar reflectors for secondary concentrators are permanently exposed to environmental conditions, high radiation fluxes and elevated temperatures that potentially cause stress and degradation throughout the time. Therefore, analyzing solar reflectors of secondary concentrators by simulating these conditions is crucial. No previous research works about the durability of solar reflector materials for secondary concentrators have been reported. The present work is focused on studying the degradation of the reflector materials by simulating accelerated aging, caused by several ambient parameters and the effect of concentrated radiation. Both cooled and uncooled systems for secondary concentrators are included in this study. According to results obtained, aluminum reflectors and thin silvered-glass reflectors glued to an aluminum structure showed minimum reflectance losses and structural degradation under the operation conditions of cooled 3D secondary concentrators (tower systems). Following critical aspects to avoid reflector degradation were identified: to select a suitable adhesive material to glue the thin silvered-glass reflector to the support aluminum structure, to properly protect reflectors edges, to design a suitable cooling system and to avoid the combination of high radiation fluxes with mechanical stress. In addition, laminated silvered-glass reflectors have shown to be suitable for uncooled 2D secondary concentrators (Fresnel collectors). Furthermore, a comparison with naturally aged secondary concentrators using silvered-glass reflectors glued to an aluminum structure revealed that the simulated degradation under accelerated conditions performed in this work did reproduce the most frequent degradation patterns suffered in real operating conditions.