• Energy Research
• 7. Clean energy close
• US close
• IN close
• DK close

Abstract Large-scale cultivation of microalgal biomass in open systems can benefit from the low cost of using natural sunlight, as opposed to artificial light, but may encounter problems with photoinhibition, high evaporation rates, potential contamination and high energy demand. Wavelength selective luminescent solar concentrator (LSC) panels can solve some of these problems when incorporated into low-cost sheltered structures for algal biomass production that concurrently produce their own electricity by harnessing select portions of solar energy, not used for algal growth. The LSC panels in this study contained a fluorescent dye, Lumogen Red 305, which transmits blue and red wavelengths used for photosynthesis with high efficiency, while absorbing the green wavelengths and re-emitting them as red wavelengths. The fluorescently generated red wavelengths are either transmitted to boost algal growth, or waveguided and captured by photovoltaic cells to be converted into electricity. We found that different strains of microalgae (currently used commercially) grew equally well under the altered spectral conditions created by the luminescent panels, compared to growth under the full solar spectrum. Thus this technology presents a new approach wherein algae can be grown under protected, controlled conditions, while the cost of operations is offset by the structure's internal electrical production, without any loss to algal growth rate or achievable biomass density.

An analytical Detailed Loop Model (DLM) has been developed to analyze the performance of solar thermosiphon water heaters with heat exchangers in storage tanks. The model has been used to study the performance of thermosiphons as a function of heat exchanger characteristics, heat transfer fluids, flow resistances, tank stratification, and tank elevation relative to the collector. The results indicate that good performance can be attained with these systems compared to thermosiphons without heat exchangers.

Abstract This paper aims to present a feasibility study of the innovative plant for methanol synthesis from carbon dioxide-sequestered by fossil fuel power plant and hydrogen, which is produced by water electrolyzer employing the over-production on the electrical grid. The thermo-economic analysis is performed in the framework of the MefCO2 H2020 EU project and it is referred to the German economic scenario, properly taking into account the real market costs and cost functions for different components of the plant. Three different plant capacities for methanol production (4000 10,000 and 50,000 ton/year) have been investigated, assuming an average cost for electrical energy to feed electrolysers and analyzing the influence of the most significant parameters (oxygen selling option, methanol selling price and electrolysers’ capital cost) on the profitability of the plant. The analysis has been performed in W-ECoMP, software for the thermo-economic analysis and plant optimization developed by the University of Genoa.

Accelerators for heavy-ion inertial fusion energy (HIF) have an economic incentive to fit beam tubes tightly to beams, putting them at risk from electron clouds produced by emission of electrons and gas from walls. Theory and PIC simulations suggest that the electrons will be radially trapped in the /spl ges/1 kV ion-beam potential. We are beginning studies on the High-Current Experiment (HCX) with unique capabilities to characterize electron production and trapping, the effects on ion beams, and mitigation techniques. We are measuring the flux of electrons and gas evolved from a target, whose angle to the beam can be varied between 78/spl deg/ and 88/spl deg/ from normal incidence. Quadrupole magnets are operating with a variety of internal charged particle diagnostics to measure the beam halo loss, net charge, electron ionization rate, and gas density.

We study the role of technology subsidies in climate policies, using a simple dynamic equilibrium model with learning-by-doing. The optimal subsidy rate of a carbon-free technology is high when the technology is first adopted, but falls significantly over the next decades. However, the efficiency costs of uniform instead of optimal subsidies, may be low if there are introduction or expansion constraints for a new technology. Finally, supporting existing energy technologies only, may lead to technology lock-in, and the impacts of lock-in increase with the learning potential of new technologies as well as the possibilities for early entry and thight carbon constraints.

The main problem involved in utilization of solar energy is low efficiency of photovoltaic conversion and high cost. The objectives of the paper are to increase the efficiency of photovoltaic cells and to reduce the cost of the photovoltaic module. A novel method is presented in this paper to increase the efficiency of photovoltaic modules and reduce the cost by the use of specially designed solar concentrators. The efficiency of photovoltaic module is increased by covering an angle of nearly 180° so that the sun's radiation converges through out the day from all angles on to a fixed flat plate module. The cost is reduced by use of cheaper glass for module and covering a wider area for the radiation. The above objectives are achieved by the use of a special arrangement of three lenses for the concentrators.

Abstract The present work attempts to devise an efficient method utilizing an on-grid photovoltaic-thermal heat pump water heater (PV-THPWH) integrated with a real-time variable frequency controller to achieve the goal of energy-efficient buildings. The prime focus is to reduce the grid's dependence on the compressor's energy-intensive operation by employing a feedback-controlled variable frequency drive (VFD). Additionally, the possibilities involved with addressing the electrical and thermal energy requirements of an energy-efficient building was investigated utilizing the proposed system. R-32 refrigerant in the photovoltaic-thermal (PV-T) evaporator coils of the heat pump assembly help to cool the photovoltaic (PV) panel while delivering the absorbed heat in the condenser to heat water contained inside the storage tank. Outdoor experiments and theoretical investigations of the combined system were carried out to appraise the dynamic behavior under varying solar irradiation and ambient temperature conditions. The observations conveyed that the PV-THPWH system succeeded in reducing the PV panel operating temperature by 25%, which resulted in a 20% increment in PV power output. Also, the performance indicators, such as the instantaneous energy efficiency and instantaneous PV efficiency, were found to increase by 15% and 34%, respectively, resulting in an average coefficient of performance of 6.4. For a clear sky day, the recorded total PV energy output was 4.67 units, while the VFD compressor consumption was 3.42 units, and the surplus 1.25 units were sent to the grid. Furthermore, the economic analysis reported a payback period of 2.3 years for the developed PV-THPWH system.

Vegetable oil and animal fat derived fatty acid methyl esters are commonly known as biodiesel and provide an environment friendly and renewable substitute for the conventional diesel fuel. The present work demonstrates an easy preparation of potassium ion impregnated calcium oxide in nano crystalline form (supported by powder X-ray diffraction and transmission electron microscopic studies) and its application as a solid catalyst for the transesterification of waste cottonseed oil with methanol. The catalyst prepared by impregnating 3.5 wt% of potassium in CaO support was found to show the best catalytic activity among the prepared catalysts. The same catalyst was found to be effective for the complete transesterification of less expensive feedstock, waste cotton seed oil, even in the presence of 10.26 wt% moisture and 4.35 wt% free fatty acid contents. The selected catalyst has also been reused successfully for three catalytic cycles. Few physicochemical properties of the prepared biodiesel sample have been studied and found to be within the acceptable limits of EN 14214 standards.