• Energy Research
• 7. Clean energy close
• 11. Sustainability close
• PL close
• US close
• ES close
• Energies close

We analyzed the peak spring tidal current speeds, annual mean tidal power densities ( T P D ) and annual energy production ( A E P ) obtained from experiment 06.1, referred as the “HYCOM model” throughout, of the three dimensional (3D), global model HYCOM in an area covering the Baja California Pacific and the Gulf of California. The HYCOM model is forced with astronomical tides and surface winds alone, and therefore is particularly suitable to assess the tidal current and wind-driven current contribution to in-stream energy resources. We find two areas within the Gulf of California, one in the Great Island Region and one in the Upper Gulf of California, where peak spring tidal flows reach speeds of 1.1 m per second. Second to fifth-generation tidal stream devices would be suitable for deployment in these two areas, which are very similar in terms of tidal in-stream energy resources. However, they are also very different in terms of sediment type and range in water depth, posing different challenges for in-stream technologies. The highest mean T P D value when excluding TPDs equal or less than 50 W m−2 (corresponding to the minimum velocity threshold for energy production) is of 172.8 W m−2, and is found near the town of San Felipe, at (lat lon) = (31.006–114.64); here energy would be produced during 39.00% of the time. Finally, wind-driven currents contribute very little to the mean T P D and the total A E P . Therefore, the device, the grid, and any energy storage plans need to take into account the periodic tidal current fluctuations, for optimal exploitation of the resources.

This research presents a 100% renewable energy (RE) scenario by 2050 with a high share of electric vehicles on the grid (V2G) developed in Ecuador with the support of the EnergyPLAN analysis tool. Hour-by-hour data iterations were performed to determine solutions among various features, including energy storage, V2G connections that spanned the distribution system, and long-term evaluation. The high participation in V2G connections keeps the electrical system available; meanwhile, the high proportions of variable renewable energy are the pillar of the joint electrical system. The layout of the sustainable mobility scenario and the high V2G participation maintain the balance of the electrical system during most of the day, simplifying the storage equipment requirements. Consequently, the influence of V2G systems on storage is a significant result that must be considered in the energy transition that Ecuador is developing in the long term. The stored electricity will not only serve as storage for future grid use. Additionally, the V2G batteries serve as a buffer between generation from diversified renewable sources and the end-use stage.

Car-sharing services are developing at an ever-increasing pace. Taking into account the reduction of carbon dioxide emissions and pursuit of the sustainable development of transport, implementing electric cars in car-sharing fleets is being proposed. On the one hand, these types of vehicles are referred to as emission-free, but on the other hand, their environmental friendliness is questionable due to the emission of carbon dioxide during the production of energy to power them. Although many scientific papers are devoted to the issue of reducing emissions through car sharing, there is a research gap concerning the real production of carbon dioxide by car-sharing vehicles during car-sharing trips. To fill this research gap, the objective of the article was to analyze the actual level of carbon dioxide emissions from combustion and electric vehicles from car-sharing systems produced when renting rides. The test results showed that the electric car turned out to be significantly less emitting. The use of electric vehicles in car-sharing fleets can reduce carbon dioxide emissions from 14% to 65% compared to using cars with internal combustion engines. However, the key role during car-sharing trips is played by the driving style of the drivers, which has been omitted from the literature to date. This should be properly regulated by service providers and focus on the proper use of energy from electric vehicle batteries, especially at low temperatures. The article provides support for operators planning to modernize their fleet of vehicles and fills the research gap concerning car-sharing emissions.

Nowadays, heating using wood, briquettes, or pellets is a curious replacement to fossil fuels such as coal, oil, or gas. Unfortunately, the combustion of biofuels, especially in low-power boilers with unstable operating conditions, releases a lot of gas pollutants (e.g., carbon monoxide (CO), nitric oxide (NO), and various organic compounds) that are usually generated due to the incomplete product combustion. The combustion of biofuel in grate boilers with top-down ignition is a new approach, popular in society (mainly used for coal fuels), which improves the combustion process and reduces the amount of pollutants emitted. This study evaluated the impact of ignition techniques on the emission level of gas pollutants during the combustion of wood logs, briquettes, and pellets of pine in grate-based charging boilers. The combination of top ignition mode with pinewood logs allowed us to achieve a reduction of 6% in CO and sulfur dioxide (SO2) emission into the atmosphere. However, the combination of top-down ignition mode with pellets and briquettes produced, in fully operational conditions, 1- to 18-fold higher levels of CO and SO2 respectively, than bottom-up ignition, after an initial period of low level CO and SO2 emissions. During the tests (mainly with ignition from top), substantial emissions of NO were observed of up to 400 mg·m−3 at 10% O2. Therefore, further research is required to decrease emission related to the content of nitrogen in biomass. In this respect, research of impact on the combustion temperature of such emissions is needed.

Microbial electrochemical technologies (METs) constitute the core of a number of emerging technologies with a high potential for treating urban wastewater due to a fascinating reaction mechanism—the electron transfer between bacteria and electrodes to transform metabolism into electrical current. In the current work, we focus on the model electroactive microorganism Geobacter sulfurreducens to explore both the design of new start-up procedures and electrochemical operations. Our chemostat-grown plug and play cells, were able to reduce the start-up period by 20-fold while enhancing chemical oxygen demand (COD) removal by more than 6-fold during this period. Moreover, a filter-press based bioreactor was successfully tested for both acetate-supplemented synthetic wastewater and real urban wastewater. This proof-of-concept pre-pilot treatment included a microbial electrolysis cell (MEC) followed in time by a microbial fuel cell (MFC) to finally generate electrical current of ca. 20 A·m−2 with a power of 10 W·m−2 while removing 42 g COD day−1·m−2. The effective removal of acetate suggests a potential use of this modular technology for treating acetogenic wastewater where Geobacter sulfurreducens outcompetes other organisms.

This paper addresses the energy conservation problem in computing systems. The focus is on energy-efficient routing protocols. We formulated and solved a network-wide optimization problem for calculating energy-aware routing for the recommended network configuration. Considering the complexity of the mathematical models of data center networks and the limitations of calculating routing by solving large-scale optimization problems, and methods described in the literature, we propose an alternative solution. We designed and developed several efficient heuristics for equal-cost multipath (ECMP) and Valiant routing that reduce the energy consumption in the computer network interconnecting computing servers. Implementing these heuristics enables the selection of routing paths and relay nodes based on current and predicted internal network load. The utility and efficiency of our methods were verified by simulation. The test cases were carried out on several synthetic network topologies, giving encouraging results. Similar results of using our efficient heuristic algorithm and solving the optimization task confirmed the usability and effectiveness of our solution. Thus, we produced well-justified recommendations for energy-aware computing system design to conclude the paper.

Aerodynamics of the Darrieus wind turbine is an extremely complex issue requiring the use of very advanced numerical methods. Additional structural components of this device, such as, for example, a rotating shaft disturb the flow through the rotor significantly impairing its aerodynamic characteristics. The main purpose of the presented research is to validate the commonly-used unsteady Reynolds averaged Navier–Stokes (URANS) approach with the shear stress transport (SST) k-ω turbulence model based on the particle image velocimetry (PIV) studies of a two-bladed rotor operating at the moderate tip speed ratio of 4.5. In the present numerical studies, a two-dimensional turbine rotor with a diameter of 1 m was considered. The following parameters were evaluated: instantaneous velocity fields; velocity profiles in the rotor shadow and aerodynamic blade loads. The obtained numerical results are comparable with the reference experimental results taken from the literature. The second purpose of this work was to examine the influence of the rotating rotor shaft/tower on the wind turbine performance. It has been proven that the cylindrical shaft reduces the power of the device by 2.5% in comparison with the non-shaft configuration.