• Energy Research
• Closed Access close
• US close
• Energy Conversion and Management close

Abstract The general objective of the investigation described in this article is the experimental testing of solar assisted dryers reported earlier. The tests show good technical results with a conventional energy consumption decrease of 27–80% and an average solar system efficiency of approx. 40%. From the experimental results, it can also be concluded that, with controlled removal of the moist air, improved product quality, significant reduction in drying time and mass losses, etc. result. The introduction of solar dryers seems to be a promising way for drying various agricultural products.

Abstract In this work, the combustion and emission fundamentals of high n-butanol/diesel ratio blend with 40% butanol (i.e., Bu40) in a heavy-duty diesel engine were investigated by experiment and simulation at constant engine speed of 1400 rpm and an IMEP of 1.0 MPa. Additionally, the impact of EGR was evaluated experimentally and compared with neat diesel fuel (i.e., Bu00). The results show that Bu40 has higher cylinder pressure, longer ignition delay, and faster burning rate than Bu00. Compared with Bu00, moreover, Bu40 has higher NOx due to wider combustion high-temperature region, lower soot due to local lower equivalence ratio distribution, and higher CO due to lower gas temperature in the late expansion process. For Bu40, EGR reduces NOx emissions dramatically with no obvious influence on soot. Meanwhile, there is no significant change in HC and CO emissions and indicated thermal efficiency (ITE) with EGR until EGR threshold is reached. When EGR rate exceeds the threshold level, HC and CO emissions increase dramatically, and ITE decreases markedly. Compared with Bu00, the threshold of Bu40 appears at lower EGR rate. Consequently, combining high butanol/diesel ratio blend with medium EGR has the potential to achieve ultra-low NOx and soot emissions simultaneously while maintaining high thermal efficiency level.

Abstract The technology landscape around distributed generation continues to evolve in response to increasing demand for high-efficiency, low-emission, low-cost power generation. While emerging distributed power technologies, such as solid oxide fuel cells (SOFCs), continue to advance, they still face challenges due to their high capital costs, and shorter lifetimes that typically arise from electrochemical stack performance degradation at high operating temperatures (>750 °C). Recent advancements in protonic ceramic fuel cells (PCFCs) offer the potential to mitigate drawbacks of their higher temperature SOFC counterparts by enabling lower operating temperatures (550 °C–600 °C) with acceptable power densities. The present work leverages the recent progress in protonic ceramic cell and stack technology development to generate viable system configurations and evaluate the energetic performance potential of PCFC-based systems for stationary power generation. Process system engineering of two water-neutral system concepts, which provide 25 kW of electric power and process hot water, are presented and evaluated through sensitivity studies. Stack design parameters are altered and used to gauge the effect on system performance characteristics, including fuel cell stack and balance-of-plant sizing requirements, and electric and cogeneration efficiencies. The study finds that the potentially high per-pass fuel utilization capability of PCFC stacks could enable unprecedented electric efficiencies approaching 70% without hybridization with other prime movers.

Abstract The energy efficiency of water supply systems can be increased through the recovery of hydraulic energy implicit to the volumes of water transported in various stages of the supply process, which can be converted into electricity through hydroelectric recovery systems. Such a process allows the use of a clean energy source that is usually neglected in water supplies, reducing its dependence on energy from the local network and the system’s operation costs. This article evaluates the possibilities and benefits of the use of water supply facilities, structures and equipment for hydraulic energy recovery, addressing several applicable hydroelectric models. A real case study was developed in Brazil to illustrate the technical, economic and environmental aspects of hydropower recovery in water supply systems.

Abstract In this work, a wickless heat pipes flat plate solar collector with a cross flow heat exchanger was investigated theoretically and experimentally under the meteorological conditions of Cairo, Egypt. The author’s earlier simulation program of wickless heat pipes flat plate solar water heaters was modified to be valid for the present type of wickless heat pipes solar collector by including the solution of the dimensionless governing equations of the present analysis. For verifying the modified simulation program, a wickless heat pipes flat plate solar collector with a cross flow heat exchanger was designed, constructed, and tested at different meteorological conditions and operating parameters. These parameters include different cooling water mass flow rates and different inlet cooling water temperatures. The comparison between the experimental results and their corresponding simulated ones showed considerable agreement. Under different climatic conditions, the experimental and theoretical results showed that the optimal mass flow rate is very close to the ASHRAE standard mass flow rate for testing conventional flat plate solar collectors. Also, the experimental and theoretical results indicated that the number of wickless heat pipes has a significant effect on the collector efficiency.

Abstract As the world’s nuclear reactor fleet continues to age, the importance of verifying the structural integrity of critical reactor components and systems has continued to increase. Some critical components are the reactor internals found in close proximity to the nuclear fuel rods which are exposed not only to high stresses and temperatures, but also to high radiation and neutron fluxes. The Materials Reliability Program (MRP-227/228) has provided guidance indicating which components are of the highest importance and susceptibility to the aging mechanisms found in nuclear reactors. These components must be either inspected or replaced in order for plants to be granted license renewals to continue commercial operations. Several inspection methods are presented that were successfully demonstrated and comply with these new guidelines to meet the requirements for license renewal.

Abstract Comparative pyrolysis behaviors of typical hardwood ( Fagus sylvatica ) and softwood ( Cunninghamia lanceolata ) were investigated based on thermogravimetric analysis over a wide heating rate range from 5 K/min to 60 K/min. The Flynn-Wall-Ozawa model-free method was applied to estimate the various activation energy values at different conversion rates, and the Coats-Redfern model-fitting method was used to predict the possible reaction mechanism. Two pyrolysis regions were established by the trend of activation energy, divided by the threshold of conversion rate (0.4 for hardwood and 0.2 for softwood) but with the same distinguished temperature at about 580 K. For the region under the conversion rate threshold, the activation energy of hardwood increased gradually while softwood decreased. Furthermore, the activation energy remained the same for both hardwood and softwood in the region over the conversion rate threshold. However, softwood behaved greater activation energy than hardwood during the whole pyrolysis process. The pyrolysis differences of hardwood and softwood could be attributed to the chemical component, molecular structure, component proportion and various extractives. The same reaction mechanism of hardwood and softwood was verified by applying the Coats-Redfern approach. By checking activation energies obtained according to different models with those obtained through the Flynn-Wall-Ozawa method, the best model was based on diffusion mechanism when the conversion rate was less than its threshold, otherwise based on reaction order (2nd to 3rd).

Abstract Interest in solar chimney power plant (SCPP) has seen resurgence due to the continuously increasing awareness on environmental concerns, particularly greenhouse gas emissions from fossil fuels, since the 21st century. Although remarkable advances in the understanding of SCPP have been achieved through extensive theoretical, experimental, and numerical studies with different focuses on various aspects of the SCPP technology, no industrial scale SCPP has been built. In response to these new scientific advances and challenges for commercialization, seven questions, including parameter influences, turbine design, flow and heat transfer characteristics, similarity analysis, and hybrid systems, are presented in this work. In addition, answers and current understanding are included to provide succinct links to latest knowledge and identify areas that require further research.